• Journal of the Korean Society of Hazard Mitigation
• /
• v.9 no.1
• /
• pp.49-55
• /
• 2009

Our domestic economy has been developed very rapidly after 1960's. Also, it is dramatically increasing traffic on road and surround environmental issues. Especially, rapid economic growth has been induced large construction of pavement, and bigger and higher traffic for transportation. These are making air pollution, traffic noise and vibration. The social requirement against the revealed road environment and traffic sound reduction is being demanded. Traffic noise of city zone is showed over the environmental specification more than 57%. In order to overcome these situations, the social attention is being increased. The quiet pavement is the same format of permeable pavement, but is not same for functional performance. In this research, it has been carried out to evaluate the fundamental-mechanical properties of hot mix asphalt for quiet pavement. Especially, couple of laboratory tests are conducted like marshall stability, resilient modulus, indirect tensile test, and compaction energy analysis with gyratory compaction curve. Also, two-layer pavement system has been adopted for developing of quiet pavement. The basic performance of hot mix asphalt of quiet pavement show a satisfaction of specification of hot mix asphalt.

• Resources Recycling
• /
• v.29 no.4
• /
• pp.15-30
• /
• 2020

Recently, it is increasing a amount of installed solar-cell rapidly, and end-of-life photovoltaic(ELP) modules are generated in according to the reduction of cell efficiency largely. Recycling of ELP modules are begun at an advanced nation already, but there are bring about environmental contamination and resource recovery problems owing to not treated ELP modules because of economic cost completely. First of all, there were researched basic study for treatment conditions of used solar cell inspection, dismantling of aluminum frame, crushing / grinding & separation of tempered glass, removal of back sheet & EVA film, leaching & precipitation recovery of valuable metals and treatment of waste water. Therefore, we establish optimum conditions through carried out of designed apparatus, installation of equipment, test operation & trouble shooting in scale of 1ton/day pilot plant test. Following to economic review, it does have the economic efficiency until to the case of tempered glass recovery, but does not have the economic value in case of total processes until to recover the valuable metals. However, there are guaranteed economic value if we are gained a large amount of the expenses through EPR supported system. It was confirmed the commercialized possibility of ELP modules recycling if there were established on the collecting ELP modules, reusing criteria, economical technology, enactment of directives and enforcement of EPR supported system efficiently.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.128-128
• /
• 2011

본 연구에서는 자동유량측정시설에 의하여 실시간으로 생산되는 자동유량측정 자료의 정상성 여부를 판단하는데 중요한 적정 측정 신뢰구간을 실시간으로 예측할 수 있는 기술을 개발하였다. 전세계적으로, 현대적인 유량측정이 시작된 이래 연속유량 산정을 위한 방법은 수위-유량관계곡선을 이용하는 방법 외에 실무적으로 활용 가능한 방법은 거의 전무한 실정이다. 수위-유량관계곡선을 이용하는 방법은 연속수위를 계측하여 이에 해당하는 연속유량을 산정하는 방법으로 수위와 유량간에 일정한 관계를 가지는 정상적인 흐름을 보이는 자연하천의 경우에 정확도가 매우 높다. 그러나 감조나 구조물 등에 의해 유량이 조절되는 경우에 유량산정의 정확도는 현저히 떨어지게 된다. 따라서 수위에서 유량을 환산하는 방법이 아닌 유량을 직접 연속으로 측정하는 방법이 꾸준히 연구되어 왔고, 이 중 가장 대표적인 방법이 자동유량측정 방법이다. 그러나 자동유량측정 방법은 유량을 연속으로 측정할 수 있다는 장점에 반해 측정된 유량의 정확도를 높이기가 매우 어렵다는 단점도 가지고 있다. 계측 자체의 기술적 한계는 주로 계측기기적인 문제로 이는 전자기, 통신 기술 등 첨단 기술의 발전과 함께 다양한 현장 시험을 통해 폭넓은 개선이 이루어지고 있다. 그러나 아직 기술적 완성도가 완전하지 못한 현실에서, 현재 설치되어 있는 자동유량측정 유량자료의 신뢰도를 높이기 위해서는 각각의 계측 시점에서 자료가 정상적으로 산정되고 있는지에 대한 검정이 필요하고, 이는 자동유량측정 자료의 정확도 확보에 매우 중요한 관건으로 작용할 수밖에 없다. 이러한 배경에서 본 연구에서는 조석성분과 유출성분을 분리하여 예측하는 방법을 새롭게 개발 적용하였다. 자료는 자료의 시간해상도 증감에 따른 실제 예측의 정확도 증감을 고려하여 가장 적절하다고 판단되는 시자료를 사용하였으며, 자료간 상관을 분석하여 주 입력 자료로 팔당댐 방류량, 한강대교 지점 수위, 전류 수위를 이용하였다. 모형의 예측 능력을 극대화하기 위하여 조석 영향을 받는 자료의 경우는 웨이블릿 변환(wavelet transform)을 이용하여 순수 유출성분과 조위성분을 분리하여 별도로 적용하였다. 그리고 예측을 위한 모형은 실시간 자료기반 모형으로 그 안정성이 인정된 서포트벡터머신(support vector machine)을 이용하였다. 이러한 과정을 통해 한강대교 지점의 순수 유출성분과 조위성분의 유량을 각각 예측한 후 두 결과를 합성하여 최종 한강 대교 지점의 유량을 산정하였다. 조석성분을 분리하여 한강대교 지점의 유량을 예측한 결과 대부분의 예측치가 95% 예측구간에 포함되었다. 그리고 조석성분을 분리하지 않은 모형과 조석성분을 분리한 모형의 예측 능력을 비교한 결과, 조석성분을 분리한 모형이 예측이 정확도가 높았다. RMSE의 경우 분리하지 않은 모형대비 23%의 예측오차가 감소하였고, NSC의 경우 0.92에서 0.95로 예측의 정확도가 증가하였다.

• Journal of the Korea Society of Computer and Information
• /
• v.24 no.11
• /
• pp.127-133
• /
• 2019

SQL is the most common language in data processing. Therefore, most of the colleges offer SQL in their curriculum. In this research, an auto scoring SQL test is proposed for the efficient results of SQL education. The system was treated with algorithms instead of using expensive DBMS(Data Base Management System) for automatic scoring, and satisfactory results were produced. For this system, the test question bank was established out of 'personnel management' and 'academic management'. It provides users with different sets of test each time. Scoring was done by dividing tables into two sections. The one that does not change the table(select) and the other that actually changes the table(update, insert, delete). In the case of a search, the answer and response were executed at first and then the results were compared and processed, the user's answers are evaluated by comparing the table with the correct answer. Modification, insertion, and deletion of table actually changes the data table, so data was restored by using ROLLBACK command. This system was implemented and tested 772 times on the 88 students in Computer Information Division of our college. The results of the implementation show that the average scoring time for a test consisting of 10 questions is 0.052 seconds, and the performance of this system is distinguished considering that multiple responses cannot be processed at the same time by a human grader, we want to develop a problem system that takes into account the difficulty of the problem into account near future.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.96-104
• /
• 2018

Military vessels are complex weapon systems consisting of various integrated onboard equipment. Since their acquisition of military equipment takes a long period of time and a prototype ship is deployed and tested, vessel development has relied on its proprietary process. However, due to the growing complexity of onboard equipment technology, application of systems engineering (SE) process has become indispensable. Nonetheless, an effective design process complementing the existing design with the SE has not yet been developed. As such, we have studied an improved basic design process for submarines based on SE. To do so, we analyzed the processes for the basic design, technical review, and requirement management. Included reviews and requirements are SRR, SFR and PDR, and SSRS, SSS, and SSDD. By combining the results in the SE framework, we built an improved basic design process that can be applied in parallel with the SE-based technical review and requirement management. To assess the process, we applied our proposed model to the submarine development undergoing the basic design phase. It is possible to effectively manage the requirements, design artifacts and improve traceability, and also utilize them as test and evaluation materials. The SE-based basic design process is expected to be useful in other kinds of vessel design.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2019.05a
• /
• pp.464-466
• /
• 2019

Controllers used in nuclear power plants require high reliability. A controller including a Field Programmable Gate Array (FPGA) and a Complex Programmable Logic Device (referred to hereinafter as FPGA) has been applied to many Nuclear Power Plants (NPP) in the past, including the APR1400 (Advanced Power Reactor 1400), a Korean digital nuclear power plant. Initially, the FPGA was considered as a general IC (Integrated Circuit) and verified only by device verification and performance testing. In the 1990s, research on FPGA verification began, and until the FPGA became a chip, it was regarded as software and the software Verification and Validation (V&V) using IEEE 1012-2004 was implemented. Currently, IEC 62566, which is a European standard, has been applied for a lot of verification. This method has been evaluated as the most sensible method to date. This is because the method of verifying the characteristics of SoC (System on Chip), which has been a problem in the existing verification method, is sufficiently applied. However, IEC 62566 is a European standard that has not yet been adopted in the United States and maintains the application of IEEE 1012 for FPGA. IEEE 1012-2004 or IEC 62566 is a technical standard. In practice, various methods are applied to meet technical standards. In this paper, we describe the procedure and important points of verification method of Nuclear Safety Class FPGA applying SoC verification method.

• Journal of the Korean Society for Environmental Technology
• /
• v.19 no.6
• /
• pp.576-585
• /
• 2018

Systematic management during the whole life cycle from construction to operation and maintenance is very important for the seven underground pipelines (waterworks, sewerage, electricity, telecommunications, gas, heating, oil including waterworks and sewerage). Especially, it is the construction process that affects the whole life cycle of underground buried pipeline. In order to construct a new city or to maintain different underground pipes, it is always necessary to dig the ground and carry out construction and related work. There is a possibility that secondary and tertiary breaks frequently occur in the pipeline construction process after the piping constructed first in this process. To solve this problem, a system is needed which can monitor damage in real time. However, the supply of electric power for continuous operation of the system is limited according to the environment of underground buried pipelines, so it is necessary to develop a stable electric power supply system using natural energy rather than existing electric power. In this study, we developed a system that can operate the pipeline monitoring system for long time (24 hours and 15 days) using natural energy using wind and solar light.

• Clean Technology
• /
• v.27 no.3
• /
• pp.207-216
• /
• 2021

Major anthropogenic emissions of elemental mercury (Hg⁰) occur from coal-fired power plants, and the emissions can be controlled successfully using NH₃-SCR (selective catalytic reduction) systems with catalysts. Although the catalysts can easily convert the gaseous mercury into Hg²⁺ species, the reactions are greatly dependent on the flue gas constituents and SCR conditions. Numerous deNO_xing catalysts have been proposed for considerable reduction in power plant mercury emissions; however, there are few studies to date of elemental mercury oxidation using SCR processes with MW- and full-scale coal-fired boilers. In these flue gas streams, the chemistry of the mercury oxidation is very complicated. Coal types, deNO_xing catalytic systems, and operating conditions are critical in determining the extent of the oxidation. Of these parameters, halogen element levels in coals may become a key vehicle for obtaining better Hg⁰ oxidation efficiency. Such halogens are Cl, Br, and F and the former one is predominant in coals. The chlorine exists in the form of salts and is transformed to gaseous HCl with a trace amount of Cl₂ during the course of coal combustion. The HCl acts as a very powerful promoter for high catalytic Hg⁰ oxidation; however, this can be strongly dependent on the type of coal because of a wide variation in the chlorine contents of coal.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.7
• /
• pp.922-930
• /
• 2020

Marine accidents involving fishing boats, caused by a loss of stability, have been increasing over the last decade. One of the main reasons for these accidents is a sudden wind attacks. In this regard, the wind loads acting on the ship hull need to be estimated accurately for safety assessments of the motion and maneuverability of the ship. Therefore, this study aims to develop a computational model for the inlet boundary condition and to numerically estimate the wind load acting on a fishing boat. In particular, wind loads acting on a fishing boat at the wind speed profile boundary condition were compared with the numerical results obtained under uniform wind speed. The wind loads were estimated at intervals of 15° over the range of 0° to 180°, and i.e., a total of 13 cases. Furthermore, a numerical mesh model was developed based on the results of the mesh dependency test. The numerical analysis was performed using the RANS-based commercial solver STAR-CCM+ (ver. 13.06) with the k-ω turbulent model in the steady state. The wind loads for surge, sway, and heave motions were reduced by 39.5 %, 41.6 %, and 46.1 % and roll, pitch, and yaw motions were 48.2 %, 50.6 %, and 36.5 %, respectively, as compared with the values under uniform wind speed. It was confirmed that the developed inlet boundary condition describing the wind speed gradient with respect to height features higher accuracy than the boundary condition of uniform wind speed. The insights obtained in this study can be useful for the development of a numerical computation method for ships.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.10 no.4
• /
• pp.457-464
• /
• 2022

In this study, XRF, Loss on ignition, SEM, and PSA analysis were performed on four types of fly ash in Vietnam and compared with fly ash in Korea. As a result, PC boiler fly ash in Vietnam has a similar chemical composition to that of PC boiler fly ash in Korea, where the content of SiO₂, Al₂O₃, and Fe₂O₃ accounts for about 70%. In addition, the result showed that blast furnace slags in Vietnam and Korea have similar quality criteria and performance. A binder material mixing test using four types of fly ash supplied from Vietnam was conducted, and the compressive strength ranged from 7.60 to 13.25 MPa after 28 days of curing. Vinh Tan fly ash showing the highest compressive strength was selected as the soil injection material for the chemical grouting method. For the formulation of the chemical grouting method, sodium silicate No.3 and silica-sol were used as liquid-A. As a result of measuring the gel time and the compressive strength of the homogel, they showed good performance satisfying the quality criteria applied in Korean construction fields. Therefore, Vinh Tan fly ash can be used as a soil injection material for the chemical grouting method.