• Journal of the Korean Geotechnical Society
• /
• v.39 no.2
• /
• pp.19-30
• /
• 2023

Underground structures, such as compacted sand piles applied as soft ground countermeasures, are analyzed for settlement and stability by the composite ground design method. The basic principle of the composite ground design method is the arching effect. The reinforcing effect of the pile is evaluated as the stress-distribution ratio. When applying grouting piles with elastic properties using the ground reinforcement method, the existing stress-distribution ratio was only considered when the pile was installed. This study shows that the method of applying the stress-distribution ratio applied in previous studies should be changed when the ground reinforcement pile is installed at an arbitrary location in the ground without raising it to the ground surface. When high strength jet routing is applied, the stress-distribution ratio (n) to the in-situ ground generally ranges from 30 to 50. However, if the pile is located far from the surface and the depth goes down to the boundary depth of the stress sphere, the stress-distribution effect rapidly decreases, and the stress-distribution ratio converges to 1.5.

• Korean Journal of Food Science and Technology
• /
• v.33 no.2
• /
• pp.166-172
• /
• 2001

In order to increase ginsenoside content, to reduce chemical change, to shorten extracting procedure, new methods of extraction and fractionation of crude ginseng saponin were established and compared for their chemical composition. Those are hot MeOH extraction/n-BuOH fractionation (BuOH method) and hot MeOH extraction/Diaion HP-20 adsorption/MeOH elution (HP-20 method), which are already known methods, and additional three new methods: hot MeOH extraction/cation AG 50W $adsorption/H_2O$ elution/n-BuOH extraction (AG 50W method), cool MeOH extraction/Diaion HP-20 adsorption/MeOH elution (cool extraction method) and direct extraction with EtOAc/n-BuOH (direct extraction method). AG 50W method provided a crude saponin showing the highest content of ginsenosides of 61.5% and the lowest contents of protein and free amino acids of 0.93% and 0.19%, respectively. The protein content was the highest as 14.18% in the crude saponin by HP-20 method, while free sugar content was the highest as 13.5% by BuOH method, indicating that these are factors that lower the rate of ginsenoside in crude saponins by those methods. On the other hand, it was revealed that AG 50W method produced large amount of prosapogenins during the pass through the cation exchange resin (AG 50W) column being strongly acidic. Crude saponin from direct extraction method showed relatively higher composition of ginsenoside $Rg_1$ and Re. The results suggest that contents and composition of ginsenosides and other chemical components in crude ginseng saponin greatly depend on the condition of the extraction and fractionation.

• Restorative Dentistry and Endodontics
• /
• v.24 no.4
• /
• pp.560-569
• /
• 1999

Blood supply rather than nerve supply implies pulp vitality. To evaluate pulp vitality clinically, electric pulp test and thermal test which are based on sensory nerve response have been used in addition to many auxiliary data such as past dental history, visual inspection, radiographic examination, percussion, palpation and transillumination test. However, reactivity of the nerves to the stimulation is not synonymous with normalcy. Therefore measurement of pulpal blood flow using a laser Doppler flowmeter became a new trial to test the pulp vitality. The purpose of the present study was to evaluate normal pulpal blood flow level of maxillary teeth in adult to provide a guideline in determining the vitality of dental pulp. Pulpal blood flow was measured in maxillary central and lateral incisors, canines, first and second premolars and first molars of seventy nine adults of 22 - 30 years old using a laser Doppler flowmeter (PeriFlux 4001, Perimed Co., Stockholm, Sweden, 780 nm infrared laser, 1mW). For directly-made splints, silicone rubber impressions were taken directly from the mouth. For indirectly-made splints, alginate impressions were taken from the mouth and stone cast were made. After making depressions on the buccal surfaces of the cast teeth to indicate the hole positions, second impressions with vinyl polysyloxane putty were taken from the cast. Holes for the laser probes were made at the putty impressions 4mm above the gingival level. Laser probe (PF416 dental probe, 1.5mm) was inserted in the prepared hole and the splint was set in the mouth. After 10 minutes of patient relaxing, pulpal blood flow was recorded for 5 minutes on each tooth. The recorded flow was saved in the computer and calculated with a software 'Perisoft' version 5.1. Pulpal blood flow was also recorded in six teeth of five individuals with no response to electric pulp test and cold test, with periapical radiolucency, or with history of root canal treatment to compare with nonvital teeth. The difference between the mean flow values of each group of teeth were analyzed using one-way ANOVA and Duncan's Multiple Range test. The results were as follows: 1. The average pulpal blood flow values of all the tested teeth of each location were between 9 - 16 Perfusion Unit. Pulpal blood flow value was highest in maxillary lateral incisors, followed by first premolars, second premolars, canines, central incisors, and then first molars (p<0.01). 2. In six anterior teeth, indirectly-made splint group showed higher pulpal blood flow values than directly-made splint group (p<0.01). In posterior teeth, however, there was no significant flow value difference between directly-made splint group and indirectly-made splint one (p>0.05). 3. Teeth with vital pulps showed higher signal values than teeth with nonvital pulps (p<0.01), and the flow photographs showed heartbeat-synchronous fluctuations and vasomotions, while those were absent in non vital tooth.

• Applied Biological Chemistry
• /
• v.49 no.3
• /
• pp.170-174
• /
• 2006

For the purpose of developing a high quality agricultural microbial inoculant, methods and materials for improving encapsulation were investigated. Preparation of capsule was conducted by improving extrusion system with micro-nozzle and peristaltic pump. The sodium alginate was selected because of its cheapness, stability of cells, and gel formation ability. The yields, physical properties and gel formation abilities of extractable alginate from sea tangle were investigated by hot water extractable and alkali soluble methods. The extraction yields of hot water extractable alginate (HWEA) and alkali soluble alginate (ASA) from sea tangle were 8 and 20%, respectively. The HWEA was almost not viscous even in 1.5% of the sample solution, whereas the ASA was very highly viscous in above 3% sample solution. The gel formation ability of each samples varied from 1.5% to 5% and the ASA showed a good gel formation ability at 3% solution as commercial alginate (CA). The soil microbial inoculant, Bacillus thuringiensis, Bacillus subtilis, Lactobacillus plantarum and Geotrichum candidum encapsulated sodium alginate with starch and zeolite for stabilizer. The survivability of encapsulated soil microbial inoculant using alginate without stabilizer appeared to be 66, 52, 70 and 50%, respectively. Inclusion of starch and zeolite with alginate bead increased viabilities in Bacillus sp. and Geotrichum candidum by 81-83% and 89%, respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.98-105
• /
• 2018

Cracks in RC members occurred as a result of material and structural factors. The crack width and a crack location are very difficult to examine. A direct crack control method and indirect crack control method to control a crack are presented in the KHBDC (LSD) and KSCDC (2012). In the KSCDC text, cracks are controlled by steel spacing indirectly under a service load. On the other hand, in the KSCDC appendix, cracks are controlled by a crack width directly under a sustained load. In particular, the loading state considered is different. On the other hand, cracks are controlled under a combination of service load and an effective elastic modulus is used in KHBDC. Therefore, in this study, an effective elastic modulus that can reflect the ratio of the sustained load and live load was applied, and a maximum steel spacing was calculated through a design crack width. A variable interpretation was carried out, and a rational crack control method was assessed. As a result, a steel spacing through the design crack width in the KSCDC was smaller than that from the design crack width in the KHBDC, which leads to a conservative design. In addition, the maximum steel spacing suggested in this study has a consistency eliminating the difference between direct crack control and indirect crack control.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.8 no.2
• /
• pp.151-163
• /
• 2006

Although various methods for effective modeling of pre-reinforced zones have been suggested for numerical analysis of large section tunnels, tunnel designers refer to empirical cases and literature reviews rather than engineering methods because ones who use commercial programs are unfamiliar with a macro-scale approach in general. Therefore, this paper suggests a simple micro-scale approach combined with the macro-scale approach to determine equivalent design parameters for effective numerical modeling of pre-reinforced zones in tunnel. This new approach is to determine the equivalent stiffness of pre-reinforced zones with combination of ground, bulb, and steel in series or/and parallel. For verification, 3-D numerical results from the suggested approach are compared with those of a realistic model. The comparison suggests that two cases make best approximation to a realistic solution: One is related to the series-parallel stiffness system (hereafter SPSS) in which bulb and steel are coupled in parallel and then connected to the ground in series, and the other is the series stiffness system (hereafter SSS) in which only bulb and steel are coupled in series. The SPSS is recommended for stiffness calculation of pre-reinforced zones because the SSS is inconvenient and time-consuming. The SPSS provides slightly bigger vertical displacement at tunnel crown in weathered rock than other cases and give almost identical results to a realistic model for horizontal displacement at tunnel spring line and ground surface settlement. Displacement trends on weathered rock and weathered soil are similar. The SPSS which is suggested in this paper represents the behavior mechanism of pre-reinforced area effectively.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.20 no.5
• /
• pp.629-640
• /
• 2007

In this paper an analytical study is carried out to improve the capacity of absorbing boundary using dashpot, one of the most widely used absorbing boundaries in FEM. Using 2-D harmonic plane wave equation, absorbing boundary condition is modified to maximize its capacity according to the incident angle. Validity of the absorbing boundary conditions which is modified is investigated by adopting the solution of Miller and Pursey. The Miller and Pursey's problem is then numerically simulated using the finite element method. The absorption ratios are calculated by comparing the displacements at the absorbing boundary to those at the free field without the absorbing boundary. The numerical study is carried out through comparison of displacement at the interior region and the boundary of the numerical model.

• Korean Journal of Crystallography
• /
• v.4 no.1
• /
• pp.6-10
• /
• 1993

11 β ,17 β -dihydroxy-9a-fluoro-l7a-methyl androst-4-en-3-one (Fluoxymesterone), CgoH29 FO,, orthorhombic, P2,2,2,, a=13.468(5) A, b= 19.554 (2)A, c=6.578(9)A, a=b=r=90˚, A (CuKa)=1.5406 A , Dm=1.289cm-3, Dc=1.299cm-3 and Z=4 at T=298k. The structure was solved by direct method using seminvariants of ggg Parity group and refined by the full-matrix least-square method, resulting model with reliability factor R=0.069 for 1098 unique reflection over 3σ . Ring A is an 1β-2a-half chair, 5 ring has a highly symmetrical chair conformation, C ring is in a distorted chair conformation and D ring is a 13aenveLope conformation. In the crystal structure, the molecules are packed with a hydrogen bond of 011-H23‥‥03(0.5+x, 1.5-y, 1.0-z) [1.94(9) A of H‥‥0.2.786(9)A of 0‥‥0 and 165(8) ˚ of

• Journal of the Korea Safety Management & Science
• /
• v.14 no.2
• /
• pp.41-48
• /
• 2012

수공구 사용시 과도한 힘은 작업성 근골격계 질환을 일으킬 수 있는 주요 원인중 하나이다. 이와 관련하여, 수공구 파지시 인체 내부에 부과되는 근력과 외적으로 작용된 힘 간의 비율을 이해하는 것이 중요하며, 이는 근육에 부과되는 과도한 힘을 최소화 시키고, 작업에 필요한 힘의 효율성을 극대화 시키는데 필수적이라 할 수 있다. 이러한 비율과 관련하여 많은 연구가 되어 왔으나, 대부분 수리적 인체역학적 모델과 같은 간접적 추정 방법에 의거하고 있는 실정이다. 이러한 인체역학적 모델을 검증하고 개선하기 위하여 해부용 팔 (cadaver)을 활용한 직접적인 근력과 악력 측정이 필수적이다. 본 연구에서는 이러한 해부용 팔을 이용하여 상지 굴근(hand flexor)을 자동으로 제어하고 근력과 함께 악력을 측정할 수 있는 Hand Motion Simulator를 개발하고, 이를 통하여 다양한 사이즈의 손잡이 파지시 요구되는 근력과 외적으로 적용된 악력을 비교함으로써 수공구 손잡이 사이즈에 따른 근력의 효율성에 대하여 측정을 해 보았다. 또한, 적용된 굴근 (FDP & FDS) 간의 힘 비율에 따른 파지법의 차이를 조사해 보았다. 내부에 주어진 근력은 외부로 작용된 악력보다 5.3배 높은 부하가 작용하였으며 이러한 수공구 손잡이 파지시 힘의 효율성 역시 FDP 와 FDS 간의 비율이 3:2 였을 때, 그리고 손잡이 크기가 작을수록 높은 결과를 보였다. 반대로 손잡이의 크기가 커질수록 힘의 효율성은 저하되었다. 또한, 손가락 관절 각도의 경우 FDP와 FDS간의 비율에 따라 상이한 자세를 나타내었다. FDP 굴근의 비율이 높을 경우 손가락 끝마디 관절 (DIP) 의 굴곡을 보였으며, FDS 굴근 비율이 높을 경우 손가락 두 번째 관절(PIP)의 굴곡을 보였다. 본 연구를 통한 결과는 추후 상지작업자에 대한 근골격계 질환 예방 기준안 마련 및 수공구 설계를 위한 기초자료로 활용이 가능할 것으로 보인다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.6
• /
• pp.519-526
• /
• 2009

This paper describes a research result of a external shape optimization study to maximize the range of the guided missile with canards and tailfins in atmospheric flight. For this purpose, the external shape optimization program which can enhance the range of a missile was developed, incorporated with the trajectory analysis and the optimization technique. In the trajectory analysis part, Missile DATCOM which utilizes the semi-empirical method was directly connected to the trajectory code to supply the aerodynamic coefficients efficiently at every time step. In the gliding flight trajectory after apogee, a maximum $C_L/C_D$ trim condition calculation module was attached under the assumption of the missile continuously flying at maximum $C_L/C_D$ condition. In the optimization part, a Response Surface Method(RSM) was adopted to reduce the computing time.