• Journal of Korea Water Resources Association
• /
• v.40 no.11
• /
• pp.899-908
• /
• 2007

In this study, wave reflection due to depression of seabed is calculated by using eigenfunction expansion method. The proper numbers of steps and evanescent modes needed for analysis are suggested by applying the eigenfunction expansion method to bottom topography of which slope or curvature varies. While satisfying shallow or intermediate water depth condition, the optimal figure of depression of seabed is obtained by calculating reflection coefficient for various depressions of seabed. The reflection coefficient with distance between the depression of seabeds is then calculated after arraying the optimal geometry in two and three rows.

• 한국전기화학회:학술대회논문집
• /
• 1999.10a
• /
• pp.49-49
• /
• 1999

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.3 no.3
• /
• pp.170-175
• /
• 1991

In order to calculate reflection coefficients of surface waves due to underwater obstacles, the hybrid boundary integral equation method is used. Numerical results based on the linear element are verified to the exact solutions for a flat bottom. Reflection coefficient and transmission coefficients for a step are compared to Young's results and the results by EFEM (Kirby et al., 1987), in which reflection coefficients decrease to zero as the periods of incident waves decrease. Reflection coefficients for a sinusiodal hump located on a constant depth increase due to the interaction between humps.

• Journal of Korea Water Resources Association
• /
• v.32 no.6
• /
• pp.675-683
• /
• 1999

The reflection coefficients of monochromatic waves propagating over a shelf with varying dimensions are theoretically calculated. The diffraction of waves by an abrupt depth change is formulated by the eigenfunction expansion method. Not only propagating mode but also evanescent modes are considered in formulation. The role of evanescent modes in reflection coefficients is investigated in detail. Water waves are obliquely as well as normally incident to the region. The obtained reflection coefficients are verified by checking conservation of wave energy.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.2
• /
• pp.23-27
• /
• 2003

Using pervious two-dimensional reflector design method, the three-dimensional reflector design method is developed for extrusion molding HID specular reflector optical design, Using this method, a HID reflector for tunnel was developed and estimated its performance.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.05a
• /
• pp.243-247
• /
• 2004

기존의 램프(백열등, HID 램프 등)를 사용하여 반사갓을 설계하면 광원중심의 기하학적 위치, 점등 자세, 램프 자체의 크기로 인한 반사갓이 커지는 등 여러 가지 제약조건에 부딪히게 된다. 근래 개발된 PLS 광원은 기존의 램프보다 그 크기가 매우 작아 조명기구의 반사갓 설계에 있어서 보다 효율적인 설계가 가능하게 되었다. 본 논문에서는 900W PLS 광원용 4각 투광기용 반사갓 설계를 위하여 개발한 기법을 소개하고 그 성능을 제시하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.5
• /
• pp.2113-2120
• /
• 2013

In this study, an efficient machine vision based inspection system is developed for the in-line measurement of phosphor resin dispensing shapes on LED chip package. Since the phosphor resin (target material) has semitransparent characteristics, illuminated light beam is reflected from the bottom of the chip as well as from the surface. Since such phenomenon can deteriorate inspection reliability, a white LED and a 635nm laser slit beams are experimentally tested to decide suitable illumination optics. Also, specular and diffuse reflection methods are tested to decide suitable optical triangulation. As a result, it can be known that the combination of a white slit beam source and specular reflection method show the best inspection results. The Catmull-Rom spline interpolation is applied to the obtained data to form smoother surface. From the results, it can be conclude that the developed system can be sucessfully applied to the in-line inspection of LED chip packaging process.

• Geophysics and Geophysical Exploration
• /
• v.6 no.1
• /
• pp.28-34
• /
• 2003

A problem of ground subsidence has been a focus of our research over the past 3 years. The purpose of this study is to investigate the disturbed stratigraphic structure by mining and to separate the possible ground subsidence area using shallow seismic reflection survey and processing. To overcome the problems such as the distortion and attenuation of seismic signal caused by ground disturbance and to acquire the high frequency data, an array with short spacing (0.3m) for both the shot and receivers, yielding near-offset (<30m) and CMP spacing of 0.15m was implemented. Data were acquired along the survey line with length of about 43m by fixed receiver array. By considering statics caused by the ground disturbance and offset distribution of data, careful processing steps such as muting and residual statics correction were applied for successful shallow reflection imaging. By correlating the ground subsidence data and stack section, possible subsidence zone could be interpreted quantitatively.

• Korean Journal of Materials Research
• /
• v.9 no.7
• /
• pp.707-714
• /
• 1999

To save electrical energy as much as 40 % for fluorescent lighting, the reflectors coated with silver reflective thin films recently became popular with higher reflectivities and long life. The thin films fabricated by using sputtering techniques are produced mainly in U.S.A. On the other hand, some silver films deposited by using evaporation methods show low adhesion in general, although the reflectivity is no problem. We have studied various PVD methods to obtain thin films with high reflectivity and adhesion on a substrate of polyester, for a couple of years. Silver films manufactured byusing evaporation showed the reflectivity of 96.4 % and the adhesion of $12 kg/\textrm{cm}^2$. while samples manufactured by using sputtering depicted the adhesion as much as $20 Kg/\textrm{cm}^2$ that is almost double, although their reflectivity was not much different. X-ray diffraction spectra for the sputtered films demonstrated a preferential growth on (111) plane and the cross-sections of the specimens revealed a dense columnar structure to result in the enhanced adhesion.

• Composites Research
• /
• v.19 no.1
• /
• pp.15-21
• /
• 2006

It is very difficult to make complex 3 dimensional curved-shape composite laminates using the advanced unidirectional composite prepregs. This study shows development process of subscale composite parabolic antenna reflector using unidirectional AS4/PEEK prepreg tapes. The AS4/PEEK thermoplastic composite materials are known to have good thermal and chemical stabilities in addition to their high specific strength and modulus. Various lamination methods were investigated through finite element analyses to make up the laminate design of the reflector. The automated fiber placement method was used to fabricate the reflector. The thermal expansion test using full-bridge strain gage circuits was done to verity the performance of the composite product.