• Journal of the Korean Society of Propulsion Engineers
• /
• v.5 no.1
• /
• pp.69-75
• /
• 2001

Linear GPA(Gas Path Analysis) and non-linear GPA programs for performance diagnostics of a turboprop engine were developed, and a study for selection of optimal measurement variables was performed. Simultaneous faults in the compressor, the compressor turbine and the power turbine, which occur damage of the engine, were assumed. The non-linear GPA analysis was carried out with an iterative method, where the performance degradation rate of independent parameters was divided into same intervals. It was compared with the result by the Newton-Raphson method for observing the effect of an iterative method. According to the analysis result, it was found that performance of non-linear GPA can be influenced on the type of the iterative method. For showing effects of the number of measurement variables both the linear and non-linear GPAs were analyzed with 10, 8 and 6 measurement sets, respectively. RMS error between them were compared each other. It was realized that the more measurement parameters are used, and the more accurate result may be obtained. However much better result can be obtained with measurement parameters selected properly Moreover, RMS error by using non-linear GPA was less than that by using linear GPA.

• Journal of the Korea Concrete Institute
• /
• v.17 no.5 s.89
• /
• pp.751-760
• /
• 2005

The chloride penetration model, which considers diffusion and sorption, is proposed. The FEM program developed on the basis of the diffusion and sorption model provides the estimation of chloride concentration variation according to cyclic humidity and temperature. The humidity diffusion analysis is carried out, and the chloride ion diffusion and sorption analysis are conducted on the basis of the pre-estimated humidity data in each element. Each element has different variables at different ages and locations in analysis. At early ages, the difference of relative humidity between inner and outer concretes causes the chloride ion penetration by sorption. As the humidity diffusion reduces the difference of relative humidity between inner md outer concretes with age, the effect of sorption on the chloride ion penetration decreases with age. The cyclic humidity increases the effect of sorption on the chloride ion penetration at early ages, and increases the quantity of chloride ion around steel at later ages. Therefore, the in-situ analysis of chloride ion Penetration for harbor concrete structures must be Performed considering the cyclic humidity conditionandthelongtermsorption.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.11 no.6
• /
• pp.396-401
• /
• 1986

The method of steepest descent is applied to the analysis of electrostatic problems. The differences between iterative method and direct method, e.g. the method of moments, are not lined. It is shown that this method converges monotonically to the exact solution and is suitable for solving a problem of large system. Numerical results are presented for electrostatic case which show a good agreement with momet solution.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.34 no.2
• /
• pp.71-75
• /
• 2021

Despite the development of computational resources, the need to analyze models is increasing. The size of model has been increased to analyze the entire structure more accurately and precisely. As the analysis model becomes larger and more complex, the computation time increases exponentially. Various industries use many structures that have repeated patterns. We focus on these structures with repeated patterns and propose a dynamic analysis method to efficiently calculate these repeated structures. To devise an efficient method for repeated structures, the substructuring scheme and the degree of freedom-based reduction method are used in this study. We modify the existing reduction method in consideration of the characteristics of the repeating structure. In the proposed method, the entire structure was expressed as a combination of substructures, where each substructure was represented as an unit cell of repeated structures. The substructures were condensed and assembled using the substructuring scheme and the modified condensation method. Finally, numerical examples were demonstrated to verify the efficiency and accuracy of proposed method.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.35 no.5
• /
• pp.287-297
• /
• 2022

This paper presents experimental and analytical studies on the lateral cyclic behavior of RC columns actively confined with iron-based shape memory alloy (Fe-SMA) strips. Based on the Anexperimental study, we investigated the effectiveness of active confinement through compression testings of concrete cylinders confined by Fe SMA strips and carbon fiber-reinforced polymer (CFRP) sheets. The test results showed that the specimens confined with Fe SMA strips significantly increased the deformation capacity of the concrete, even under lower confining pressures, compared to those specimensconfined with CFRP sheets. The experimental results were used to develop finite-element models of RC columns confined with Fe SMA or CFRP in their plastic-hinge region. After validating the proposed analytical model through comparison with the results from a previous RC column test, a series of lateral cyclic load analyses were carried out for the RC columns confined with Fe SMA and CFRP. The analytical results revealed that the lateral cyclic behavior of the Fe SMA-confined column was greatly enhanced in terms of deformation and energy dissipation capacities compared with tothat of the as-built and CFRP-confined columns.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2000.11a
• /
• pp.429-434
• /
• 2000

본 연구에서는 등분포하중을 받는 laminated 박판의 거동해석을 제시하였다. 접착한 두 박판의 비선형 지배방정식을 Von Karman 식을 이용하여 유도하고 박판의 거동을 차분법을 이용하여 수치해석 한다. Interlayer에서의 전단변형을 고려하여 지배방정식에 포함시켜 하중 증분법(load incremental method)으로 기하학 비선형 해석을 수행한다. 하중 증분법에 따른 반복법을 도입하여 비선형 방정식을 해석했다. 해석방법의 타당성을 입증하기 위하여 해석결과들을 기존의 문헌의 결과와 비교, 검토함으로써 본 논문에서 제시한 이론 및 해석방법의 타당성을 입증한다. 차분법의 하중 증분법 알고리즘을 개발하여 예제문제에 대한 수치해석 결과들을 논하였다.(중략)

• Science of Emotion and Sensibility
• /
• v.16 no.4
• /
• pp.503-508
• /
• 2013

This study aims to analyze using RQA(Recurrence Quantification Analysis) about difference of electroencephalogram between inattention and attention among nonlinear methods for school age children who need attention. The experiments were conducted by 21 healthy subjects(12 males and 9 females). Inattention state is 500msec before the beginning of the auditory stimuli, attention state is 500msec after the beginning of auditory stimuli. The results of RQA parameters are greater in attention state than inattention state. It showed a statistically difference(p < 0.05). According to two states, auditory evoked potentials are displayed RP and CRP in diagram form to confirm nonlinear characteristics and The brain dynamics in the attention is more complex than the inattention. It is feasible that the RQA can be useful for the analysis of complex brain dynamics associated during auditory attentional task.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.13 no.2
• /
• pp.245-256
• /
• 2000

A moment-curvature relationship to simulate the behavior of reinforced concrete beam under cyclic loading is introduced. Unlike previous moment-curvature models and the layered section approach, the proposed model takes into consideration the bond-slip effect by using monotonic moment-curvature relationship constructed on the basis of the bond-slip relation and corresponding equilibrium equation at each nodal point. In addition, the use of curved unloading and reloading branches inferred from the stress-strain relation of steel gives more exact numerical result. The advantages of the proposed model, comparing to layered section approach, may be on the reduction in calculation time and memory space in case of its application to large structures. The modification of the moment-curvature relation to reflect the fixed-end rotation and pinching effect is also introduced. Finally, correlation studies between analytical results and experimental studies are conducted to establish the validity of the proposed model.

• Computational Structural Engineering
• /
• v.4 no.1
• /
• pp.73-82
• /
• 1991

Recently, the finite element method has been sucessfully extended to treat the rather complex phenomena such as nonlinear buckling problems which are of considerable practical interest. In this study, a finite element program to evaluate the elasto-plastic buckling stress is developed. The Stowell's deformation theory for the plastic buckling of flat plates, which is in good agreement with experimental results, is used to evaluate bending stiffness matrix. A bifurcation analysis is performed to compute the elasto-plastic buckling stress. The subspace iteration method is employed to find the eigenvalues. The results are compared with corresponding exact solutions to the governing equations presented by Stowell and also with experimental data due to Pride. The developed program is applied to obtain elastic and elasto-plastic buckling stresses for various loading cases. The effect of different plate aspect ratio is also investigated.

• Magazine of the Korea Concrete Institute
• /
• v.2 no.2
• /
• pp.73-80
• /
• 1990

The current analytical techniques for R/C elements under severe dynamic repeated loads, like earth¬quake or impact, have two major problems; one is that the effects of strain rate are not considered and the other one is the current analytical model was developed based on flexural behavior only. This study develops computer software that can idealize the flexural and shear behavior of R/C elements using several parameters and also can consider the effects of strain rate. The analytical results using the developed technique were compared with serveral experimental results and they were generally satisfied.