• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.9
• /
• pp.995-1000
• /
• 2016

The maximum cross-correntropy (MCC) algorithm with a set of random symbols keeps its optimum weights undisturbed from impulsive noise unlike MSE-based algorithms and its main factor has been known to be the input magnitude controller (IMC) that adjusts the input intensity according to error power. In this paper, a normalization of the step size of the MCC algorithm by the power of IMC output is proposed. The IMC output power is tracked recursively through a single-pole low-pass filter. In the simulation under impulsive noise with two different multipath channels, the steady state MSE and convergence speed of the proposed algorithm is found to be enhanced by about 1 dB and 500 samples, respectively, compared to the conventional MCC algorithm.

• Journal of the Society of Disaster Information
• /
• v.12 no.3
• /
• pp.279-285
• /
• 2016

Road sides safety barrier system is the last safety during traffic accident. The structural performance of a roadside safety barrier should be kept above expectations. It is possible to protect the passenger's life. End treatment part is installed in the end of the barrier it prevents a phenomenon in which for the vehicle for the guardrail during a vehicle collision it is facility of the absorbing of car crashed impact. By repeated analysis through computer simulation for improving the vehicle crash it will be able to develop crash barriers to respond appropriately to various parameters.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.4
• /
• pp.94-103
• /
• 2016

For elevated railway station on which track is connected with superstructure of station, structural vibration level and structure-borne-noise level has exceeded the reference level due to structural characteristics which transmits vibration directly. Therefore, existing elevated railway station is in need of economical and effective vibration reduction method which enable train service without interruption. In this study, structural vibration non-transmissible system which is applied to vibroisolating material for column member is developed to reduce vibration. That system is cut covering material of the column section using water-jet method and is installed with vibroisolating material on cut section. To verify vibration reduction effect and structural performance for structural vibration non-transmissible system, impact hammer test and cyclic lateral load test are performed for 1/4 scale test specimens. It is observed that natural period which means vibration response characteristics is shifted, and damping ratio is increased about 15~30% which means that system is effective to reduce structural vibration through vibration test. Also load-displacement relation and stiffness change rate of the columns are examined, and it is shown that ductility and energy dissipation capacity is increased. From test results, it is found that vibration non-transmissible system which is applied to column member enable to maintains structural function.

• Korean Journal of Materials Research
• /
• v.10 no.5
• /
• pp.354-659
• /
• 2000

Applications of composite materials have been in progress noticeably in manufacturing areas of automotive, aircraft and in other industries, resulting in ensuing research activities. Carbon-epoxy, one of major composite materials, is investigated for its thermal characteristics. Upon treatments of the composite material with repeated heatings and coolings variations of its elastic constants are monitored to reveal the thermal nature of the composite material. In this study, generally, changes in elastic constants are observed to occur mostly during the first 10~20 thermal cycles. Values of G(sub)13 remain almost unchanged except a minor decrease. However in the observed small changes thermal shocks produce less effect than thermal fatigues. On the other hand, values of $E_1$show gradual increases with the num-ber of applied thermal cycles and temperatures. Meanwhile, values of $E_2$ and G(sub)23 decrease to a certain extent in the early stage during the applications of thermal cycling but are not appreciable affected by frequencies of thermal cy-cles. Also, thermal shocks are observed to induce different effects depending on treatment temperatures.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.7 no.4
• /
• pp.216-223
• /
• 2004

A nonlinear sloshing problem is numerically simulated. During excessive sloshing the sloshinginduced impact load can cause a critical damage on the tank structure. A three-dimensional free-surface flow in a tank is formulated in the scope of potential flow theory. The exact nonlinear free-surface condition is satisfied numerically. A finite-element method based on Hamiltons principle is employed as a numerical scheme. The problem is treated as an initial-value problem. The computations are made through an iterative method at each time step. The hydrodynamic loading on the pillar in the tank is computed.

• Korean Journal of Applied Biomechanics
• /
• v.19 no.2
• /
• pp.379-386
• /
• 2009

During running, the human body experiences repeated impact force between the foot and the ground. The impact force is highly associated with injury of the lower extremity, comfort and running performance. Therefore, shoemakers have developed shoes with various midsole properties to prevent the injury of lower extremity, improve the comfort and enhance the running performance. The purpose of this study is to investigate the influence of midsole hardness on vertical ground force and heel strike angle during men's and women's running. Five male and five female expert runners consented to participate in the study and ran at a constant speed with three different pairs of shoes with soft, medium and hard midsole respectively. In conclusion, regardless of gender, there was ill significant difference among three shoes in maximum vertical ground reaction force, impact force peak and stance time. However, the loading time decreased and the loading rate increased as the midsole became harder. Female subjects showed more sensitive reaction with respect to the midsole hardness, while male subjects showed subtle difference. The authors expect to apply this results for providing a guideline for utilizing proper midsole hardness of gender-specific shoe.

• International Journal of Highway Engineering
• /
• v.12 no.3
• /
• pp.71-77
• /
• 2010

Anti-freezing layer does not used in case of non frost heaving in subgrade soils. In this case, the modulus of subgrade soils were varied with freezing and thaw cycles under non frost heaving. That effect should be properly considered in pavement design. Impact resonance test that is nondestructive testing method was used for continuously determining the modulus of subgrade soils during freezing and thaw cycle. The modulus of subgrade soils was identical with freezing and thaw cycles under closed freezing and thaw system which is no water supplement into specimen during testing. There was also no difference in the modulus of subgrade soil between before and after freezing-thaw cycles for all specimens with different water content and density. That is thaw-weakening of subgrade soils do not occur under closed freezing and thaw system. The moduli at freezing conditions are varied with water content and density, but it can be ignored in practical design sense.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.226-226
• /
• 2008

지난 10여년 동안 Sn-3.0Ag-0.5(wt%)Cu 합금은 대표 무연솔더 조성으로 다양한 전자제품의 실장 및 접합에 적용되어 왔으며, 그 신뢰성 역시 충분히 검증된 바 있다. 그러나 최근 Ag 가격의 급격한 상승과 솔더 접합부의 내 충격 신뢰성을 보다 향상시키고자 하는 업계의 동향은 Ag의 함량이 낮은 무연솔더 조성의 적용 확대를 유도하고 있다. 이에 따라 본 연구자들은 저 Ag 함유 무연슬더로 Sn-1.2Ag-0.5Cu-0.4In 조성을 제안한 바 있는데, 이는 Sn-3.0Ag-0.5Cu 조성 이상의 solderability를 가지면서도 그 금속원료 가격이 약 20% 가량 저렴한 특징을 가진다. 또한 열 싸이클링 (cycling) 테스트를 통한 슬더 조인트의 신뢰성을 평가한 결과, Sn-3.0Ag-0.5Cu에 크게 뒤떨어지지 않는 양호한 특성이 관찰되었다. 따라서 본 연구에서는 열 싸이클링 테스트와 더불어 최근 그 중요성이 지속적으로 커지고 있는 내 충격 신뢰성 평가 시험을 실시하여 개발된 4원계 무연솔더 조성의 기계적 특성을 기존 무연솔더 조성과 비교, 분석해 보았다. 각 솔더 조성은 솔더 볼 형태로 제조되어 CSP(Chip Scale Package) 상에 범핑 (bumping)되었으며, CSP를 PCB(Printed Circuit Board) 상에 실장하는 공정에서도 Sn-3.0Ag-0.5Cu 및 Sn-1.2Ag-0.5Cu-0.4In의 두 종류의 솔더 페이스트가 사용되었다. 본 연구에서의 내 충격 신뢰성 시험에는 자체 제작한 rod drop 시험기를 사용하였는데, 고정된 CSP 실장 board의 후면 부위를 일정한 높이에서 추를 반복적으로 자유 낙하시켜 급격한 충격을 주는 방식으로 실험을 실시하였다. 이 때 추의 무게는 30g, 낙하 높이는 10cm 였으며, 추의 낙하 시 측정된 board 의 휨 변위량은 약 0.7mm로 측정되었다. 사용된 CSP와 PCB 는 모두 daisy chain 방식으로 연결되어 있기 때문에 저항측정기를 사용한 간단한 실시간 저항 측정 방법으로 시험 이력에 따른 파단부의 발생 시점과 대략의 위치를 손쉽게 확인할 수 있었다. 솔더 조인트의 파단 기준 저항값으로 $1000\Omega$을 설정하였으며. 각 조건 당 5 개 이상의 샘플에 대해 평가를 실시한 후 그 평균값을 조사하였다. 시험 결과 제안된 Sn-1.2Ag-0.5Cu-0.4In 조성은 대표적인 저 Ag 함유 조성인 Sn-1.0Ag-0.5Cu에 비해서는 떨어지는 내 충격 신뢰성을 나타내었지만, 우수한 연성에 기인하여 Sn-3.0Ag-0.5Cu 조성에 비해서는 약 2 배 이상 우수한 신뢰성이 관찰되었다. 또한 CSP의 실장 시 Sn-3.0Ag-0.5Cu보다 Sn-1.2Ag-0.5Cu-0.4In 조성 솔더 페이스트를 적용한 경우에서 보다 우수한 내 충격 신뢰성을 나타내어 기본적으로 개발된 Sn-1.2Ag-0.5Cu-0.4In 솔더 페이스트가 Sn-3.0Ag-0.5Cu 조성의 기존 솔더 페이스트 보다 내 충격 신뢰성이 우수함을 검증할 수 있었다. 각 조성의 솔더 조인트를 $150^{\circ}C$ 에서 500시간 aging한 후 실시한 내 충격 신뢰성 평가에서는 모든 조성에서 그 신뢰성이 급감하는 경항을 나타내었으나, Sn-1.2Ag-0.5Cu-0.4In가 Sn-l.0Ag-0.5Cu보다도 그 상대적인 신뢰성이 우수한 것으로 관찰되었다. 이와 같이 aging 후 실시하는 충격시험은 가장 실제적인 상황과 유사한 조건이므로 상기의 실험 결과는 매우 고무적이었으며, 이에 대한 보다 면밀한 분석이 요청되었다. 마지막으로 파면 및 미세조직 관찰을 통하여 각 조성에서의 충격 파단 특성을 비교, 분석해 보았다.

• The Journal of the Acoustical Society of Korea
• /
• v.25 no.2
• /
• pp.49-55
• /
• 2006

Measurement of impact sound insulation of floor, by current Korean Standard KS F 2810-2. is to be made with peak levels over 4 point in a receiving room. But it is often the case that there is inconsistency in results at various receiving points in the receiving room. Such variations obviously have effects on the repeatability and reproducibility of measured data. The result shows that there are even 10 dB deviations in 63Hz octave band frequency range and relatively less variations are occurred in other low frequency ranges. Such variations seems to be coming from modal overlaps of the receiving room. According to current rating method of floor impact sound. KS F 2863-2, that may affect on the single number latins scheme. From the result of tests in this study, there are 2dB to 6dB differences in the sin91e number with the combination of measurement points. This means that the reduction of measurement variations from the microphone positions is needed for a better credibility of measurement results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.181-181
• /
• 2009

전자부품용 Pb-free sealing frit의 열팽창계수를 기판에 matching 시키기 위하여 음의 열팽창계수를 가지고 있는 $\beta$-Eucryptite, $\beta$-Spodumene를 합성하여 filler로 첨가하였다. 합성된 filler는 저온소성용 유리프리트의 높은 열팽창계수를 조절하기 용이하고, 유리프리트와 복합화 하여 소성하면 낮은 열팽창계수로 인한 우수한 열충격 저항성을 갖는다. Filler로써 $\beta$-Eucryptite, $\beta$-Spodumene의 결정성을 향상시키기 위해 $1250^{\circ}C$에서 5 시간 동안 유지하는 합성공정을 3회 반복 진행한 후 XRD를 사용하여 결정성을 분석하였고, TMA를 이용하여 filler 첨가량에 따른 유리프리트의 열팽장계수의 변화를 측정하였다. 또한, filler 입도와 함량에 따른 melting 특성을 분석하기 위해 Pill test를 진행하였으며, soda-lime glass 기판과의 접합면을 SEM을 사용하여 관찰하였다.