• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.7
• /
• pp.1654-1663
• /
• 1994

Even if the ball bearing was conservatively designed considering the dynamic capacity and the rating life, sometimes the bearing was early failed on account of the misalignment and the lubricant contaminations etc. Misalignment was generated when bearing-shaft system transmitted large power and when the bearing was inadequately mounted. It was possible to predict the fatigue life of ball bearing under the misalignment considering the motions of ball, cage and raceway, and the factors of the effect on fatigue life. Misalignment affected on ball bearing as radial and moment load and the relationships between misalignment and moment were obtained. In this paper, the analysis of the load distributions between ball and raceway, and the prediction of fatigue life of deep groove ball bearing under radial and moment loads were carried out. And, the new formulation of equivalent dynamic load considering the effects of moment load was proposed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.5
• /
• pp.489-495
• /
• 2016

This study focuses on a detailed ball-bearing model for spur gears. The nonlinear ball-bearing stiffness with radial clearance is derived and calculated. The bearing stiffness is used to the 3-degree-of-freedom (DOF) spur gear system model. The mode characteristics of the gear system model are analyzed and verified by performing finite-element analysis (FEA). From the results, the bearing stiffness on the radial clearance was more sensitive under low-load conditions compared to high-load conditions. The bearing stiffness significantly affected the gear dynamics in the low-frequency region, while the mesh stiffness affected the high natural frequency.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.10a
• /
• pp.25-28
• /
• 2003

The bearing/sealing test (BST) facility is intended for tests of bearing and seal for turbopump of liquid rocket engine (LRE) in various media (water, liquid nitrogen, liquid oxygen). The bearing test for serviceability is fulfilled with the estimation of the flow rate of cooling medium through the test bearing separator and with the simulation of axial and(or) radial loading. The purpose of seals test is the determination of magnitude of leakages through the seal and a time variation of this magnitude.

• Journal of the Korean Institute of Gas
• /
• v.8 no.3 s.24
• /
• pp.8-15
• /
• 2004

This paper presents von Mises stress, deformation, and rotating distortion moment characteristics of inner tank bottom plate as a function of a cryogenic temperature difference along the radial distance from the center area to the corner one. The calculated results show that the filling level of LNG at the beginning of the cool-down process is very important for the design safety analysis of the inner tank. Obviously the thermal loading by a temperature difference between the LNG vapor gas of $-80^{\circ}C$ and a LNG temperature of $-162^{\circ}C$ affects to the thermal related characteristics of the bottom plates and annular one. From the computed results, the temperature difference by a vapor gas and liquid of LNG may lead to the thermal instability of the bottom plate. This phenomenon may cause the system failure of an inner tank.

• Proceedings of the KAIS Fall Conference
• /
• 2009.12a
• /
• pp.885-888
• /
• 2009

자동차용 Alloy Wheel은 차량의 수직하중이나 가로 방향 하중, 구동, 제동토크 등 주행 시에 발생하는 여러 형태의 응력을 받으면서 사용되므로 이러한 응력을 견딜 수 있는 강성은 물론 차량 부품으로서의 요구 수명도 만족하여야 한다. 알루미늄 휠은 개발 후 규격에 준하는 내구성 평가를 위하여 반경 방향 부하 내구시험과 굽힘모멘트 내구시험과 주행 중 요철이나 벽돌 등에 의한 노면으로부터 갑작스런 하중에 대한 내충격성 평가를 위한 충격시험이 실행되고 있다. 이러한 시험은 많은 시간이 소요되고 있으며, 또한 시험 중 불합격 판정이 날 경우 또다시 처음의 공정을 모두 거쳐 다시 시험을 하게 된다. 3 Piece와 같은 알루미늄 휠은 여러 공정에 의한 생산되어지기 때문에 많은 시간적, 물질적 손실이 일어나고 있다. 따라서 자동차용 알루미늄 휠의 요구조건을 충분히 만족시키며 소비자의 요구에 맞는 품질과 시간을 충족시켜 기업경쟁력 확보는 물론 원가절감에 의한 기업 경쟁력 향상을 위하여 설계 단계서부터 시험조건을 고려한 내구성 해석에 의한 알루미늄 휠의 시험횟수를 단축하고자 한다. 본 논문에서는 3 Piece 알루미늄 휠의 축(shaft)하중에 의한 내구성 평가에 대하여 CAE시스템을 이용하여 보다 빠르고 정확한 결과를 산출함으로서 설계시간의 단축은 물론 다양한 형상의 제품들을 설계단계에서부터 생산에 이르기까지의 해석활용법을 수립하고자 하였다.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.6
• /
• pp.1125-1146
• /
• 2018

Segment lining applied to the TBM tunnel is mainly made of concrete, and it requires sufficient structural capacity to resist loads received during the construction and also after the completion. When segment lining is design to the Limit State Design, both Ultimate Limit State (ULS) and Service Limit State (SLS) should be met for the possible load cases that covers both permanent and temporary load cases - such as load applied by TBM. When design segment lining, it is important to check structural capacity at the joints as both temporary and permanent loads are always transferred through the segment joints, and sometimes the load applied to the joint is high enough to damage the segment - so called bursting failure. According to the various design guides from UK (PAS 8810, 2016), compression stress at the joint surface can generate bursting failure of the segment. This is normally from the TBM's jacking force applied at the circumferential joint, and the lining's hoop thrust generated from the permanent loads applied at the radial joint. Therefore, precast concrete segment lining's joints shall be designed to have sufficient structural capacity to resist bursting stresses generated by the TBM's jacking force and by the hoop thrust. In this study, bursting stress at the segment joints are calculated, and the joint's structural capacity was assessed using Leonhardt (1964) and FEM analysis for three different design cases. For those three analysis cases, hoop thrust at the radial joint was calculated with the application of the most widely used limit state design codes Eurocode and AASHTO LRFD (2017). For the circumferential joints bursting design, an assumed TBM jack force was used with considering of the construction tolerance of the segments and the eccentricity of the jack's position. The analysis results show reinforcement is needed as joint bursting stresses exceeds the allowable tensile strength of concrete. This highlights that joint bursting check shall be considered as a mandatory design item in the limit state design of the segment lining.

• Journal of Energy Engineering
• /
• v.28 no.3
• /
• pp.1-9
• /
• 2019

A major stress determining the remaining life of the tube in feedwater heater of fossil fuel power plant is hoop stress by the internal pressure. However, thermal stress due to temperature difference across the wall thickness also contributed to reduce the remaining life of the tube. Therefore, thermal loading must be considered even though the contribution of internal pressure loading to the stresses of the tube was known to be much higher than that of the thermal loading. In this study, thermal stress of the tubes in the de-superheating zone was estimated, which was generated due to the temperature difference across the tube thickness. Analytic equations were shown for determining the hoop stress and the radial stress of the tube with uniform thinning and for the temperature across the tube thickness. Accuracy and effectiveness of the analytic equations for the stresses were verified by comparing the results obtained by the analytic equations with those obtained from finite element analysis. Using finite element analysis, the stresses for eccentric thinning were also determined. The effect of heat transfer coefficient on thermal stress was investigated using series of finite element analyses with various values of heat transfer coefficient for both inner and outer surface of the tube. It was shown that the effect of heat transfer coefficient at outer surface was larger than that of heat transfer coefficient at inner surface on the thermal stress of the tube. Also, the hoop stress was larger than the radial stress for both cases of uniformly and eccentrically thinned tubes when the thermal loading was only considered without internal pressure loading.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.6
• /
• pp.1104-1117
• /
• 1989

본 연구는 축방향의 동압축하중(axial dynamic compression)을 받는 작은 중공원판이 고변형도율(.epsilon.＞1,000/sec), 고변형률(.epsilon.=ln(h/h$_{o}$ )＞1.0)로 변형하는 재료에 대해서 연구하고자 한다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.11
• /
• pp.1379-1386
• /
• 2013

The present work reports the mismatch limit loads for a V-groove welded pipe for a circumferential crack using finite element (FE) analyses. To integrate the effect of groove angles on mismatch limit loads, one geometry-related slenderness parameter was modified by relevant geometric parameters including the groove angle, crack depth, and root opening based on plastic deformation patterns in the theory of plasticity. Circumferential through-wall cracks are located at the centre of the weldments with two different groove angles ($45^{\circ}$, $90^{\circ}$). With regard to the loading conditions, axial (longitudinal) tension and bending are applied for all cases. For the parent and weld metal, elastic-perfectly plastic materials are considered to simulate and analyze under- and over-matching conditions in plasticity. The overall results from the proposed solutions are found to be similar to the FE results.

• Composites Research
• /
• v.12 no.5
• /
• pp.65-79
• /
• 1999

This paper descrives the method to analyzed the free vibratioin of supported composite cylindrical shells with a longitudinal, interior rectangular plate. To obtain the free vibration characteristics before the combination of two structures, the energy principle based on the classical plate theory and Love's thin shell theory is adopted. The frequency equation of the combined system is formulated using the receptance method. When the line load and moment applied along the joint are assumed as the the Dirac delta and sinusolidal function, the continuity conditions at the joint of the plate and shell are proven to be satisfied. The effects on the combined shell frequencies of the length-no-radius ratios and radius-to-thickness ratios of the shell, fiber orientation angles and orthotropic modulus ratios of the composite are also examined.