• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.1 no.1
• /
• pp.96-107
• /
• 2002

• Korea Multimedia Society
• /
• v.15 no.3_4
• /
• pp.1-16
• /
• 2011

• Electronics and Telecommunications Trends
• /
• v.23 no.2 s.110
• /
• pp.13-22
• /
• 2008

• The Magazine of the IEIE
• /
• v.29 no.6
• /
• pp.688-688
• /
• 2002

• The Magazine of the IEIE
• /
• v.34 no.2
• /
• pp.17-28
• /
• 2007

• The Journal of the Korean dental association
• /
• v.29 no.5 s.264
• /
• pp.322-324
• /
• 1991

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.2021_2022
• /
• 2009

Partial discharges(PD) is a important factor to evaluate the insulation state in high voltage electric machinery. However, measuring PD under the circumstances of power plant is occasionally impossible due to the relatively high magnitude of noise which is emanated from the operating machinery. In some case, the instrument measuring PD can not even perform a calibration that initializes tools and enhance the accuracy. This paper presents that we devised a noise reduction method and demonstrated the usefulness in acquiring reliable PD signals. We attached a series of filter and transformer at the input of power source of the instruments which refrains high noise signals from incoming to the instruments. We experimented the efficiency of noise reduction applying the device into the Dangjin Power Plant and Factory. As a result of testing with the filter and transformer, we can easily calibrate the PD signal compared to the case without the device. Additionally, we can detect the small PD signal which was unperceived with a normal device.

• Journal of the Korean Applied Science and Technology
• /
• v.6 no.2
• /
• pp.59-65
• /
• 1989

The rate constants of the hydrolysis of cinnamanilide derivatives were determined UV spectrometry in $H_2SO_4\;(5{\sim}20N)$, NaOH($5{\sim}11N)\;at\;50{\sim}110^{\circ}C$ and rate equation could be applied over a strong acid and strong base were obtained. Final product of the hydrolysis was a cinnamic acid. The ${\rho}$ values obtained from the slope of linear plots of log $k_{abs}$ vs. Hammet $t{\sigma}$ constants were slightly negatives, Substituents on cinnamanilide showed a relatively small effect, with hydrolysis facilitated be electron donating group. Activation energy(Ea)was also calculated for the hydrolysis of the cinnamanilide. From this reaction rate equation, substituent effect and experimental of rate constants, that the hydrolysis of cinnamanillde was Initiated by the netural molecule of $H_2O$ which do not dissociate at strong acid, and proceeded by hydroxide ion at strong base.

• Analytical Science and Technology
• /
• v.9 no.4
• /
• pp.373-381
• /
• 1996

Algal biomass was used in our study in order to remove some metals. After packing of 40~60 mesh algae powder into column for use of metal adsorbent, the metal solution of 1mL/min of flow rate was eluted to adsorb in algae. More amount of Cu(II) or Zn(II) ion in green algae, Ulva pertusa Kjellman than in brown algae, Sargassum horneri (Turner) C. Agarch were adsorbed and Cu(II) ion was more adsorbed in both algae than Zn(II) ion. Recovery of metal from algae is showing higher in acidic or neutral than in alkalic conditions. Cu(II) ion is recovered relatively higher than Zn(II) ion in our system.

• Journal of Power System Engineering
• /
• v.15 no.5
• /
• pp.22-29
• /
• 2011

In this study, the damage mechanism of large scale steam turbine due to water induction was analyzed and recovery characteristics were reviewed. A turbine consists of the rotating rotor and the stationary casing, and the clearance between them is very small for the efficiency enhancement. If water induction, while relatively cold steam or water is introduced into turbine, occurs, the considerable humping is caused at the casing near the initial water induction point and that induces the rubbing between rotor and casing. Finally, it leads to the catastrophic failure. Bowed rotor has the different characteristics in the recovery depending on damage degree. The elastic deformation due to light rubbing is recovered by turning the rotor with 3 rpm under normal operation condition, but most plastic deformation due to rubbing deforms the local microstructure and that results in permanent deformation which could not be recovered under normal operation condition. Bowed rotor has diverse characteristics depending on the recovery method, and the method is empirical and needs the cutting edge technology. Careful recovery treatment of the rotor will eliminate the risks and secure the high quality rotor similar to new rotor. If any critical error is made during the recovery, the rotor would not be recovered permanently and it should be scrapped.