• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.5
• /
• pp.39-45
• /
• 2009

An experimental research with 2.0 liter 4-cylinder turbocharged diesel engine was carried out to investigate the combustion and emission characteristics for various alternative fuels. The conventional diesel fuel, neat GTL, blends of 80% of GTL and 20% of biodiesel derived from waste cooking oil are utilized without any modification of engine hardware and ECU data. For GTL and blends of GTL/biodiesel fuel, the ignition delay decreased at the same operating conditions, and overall combustion duration increased slightly. Also, the peak cylinder pressure increased for blends of GTL/biodiesel compared to diesel and GTL fuel. THC and CO emissions with blends of GTL/biodiesel compared to other fuels decreased for the low and middle load conditions. But NOx emission increased due to oxygen content in biodiesel. The number concentrations of PM are higher for blends of GTL/biodiesel than other test fuels in the nucleation mode, while it had an opposite tendency in the accumulation mode, which implies more reduction of PM for blends of GTL/biodiesel on the base of mass concentration.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.1
• /
• pp.105-113
• /
• 2009

The performance of a direct-injection type diesel engine often depends on the strength of swirl or squish, shape of combustion chamber, the number of nozzle holes, etc. This is of course because the combustion in the cylinder was affected by the mixture formation process. In this paper, combustion process of biodiesel fuel was studied by employing the piston which has several grooves with inclined plane on the piston crown to generate swirl during the compression stroke in the cylinder in order to improve the atomization of high viscosity fuel such as biodiesel fuel and toroidal type piston generally used in high speed diesel engine. To take a photograph of flame, single cylinder, four stroke diesel engine was remodeled into two stroke visible engine and high speed video camera was used. The results obtained are summarized as follows; (1) In the case of toroidal piston, when biodiesel fuel was supplied to plunger type injection system which has very low injection pressure as compared with common-rail injection system, the flame propagation speed was slowed and the maximum combustion pressure became lower. These phenomena became further aggravated as the fuel viscosity gets higher. (2) In the case of swirl groove piston, early stage of combustion such as rapid ignition timing and flame propagation was activated by intensifying the air flow in the cylinder. (3) Combustion process of biodiesel fuel was improved by the reason mentioned in paragraph (2) above. Consequently, the swirl grooves would also function to improve the combustion of high viscosity fuel.

• Journal of ILASS-Korea
• /
• v.12 no.3
• /
• pp.131-137
• /
• 2007

This is an experimental study on characteristics of engine performance and discharged materials in common-rail type diesel engine. The bio-diesel fuel is mixed with the diesel fuel in common use at the ratio of 20% or 100%. The diesel fuel and blended fuel is irradiated by ultrasonic wave energy. The diese1 fuel, blended fuel, reformed diesel fuel and reformed blended fuel by ultrasonic wave energy are applied to the experimental engine individually. The results are compared with one of the diesel fuel in common use and analyzed.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2003.11a
• /
• pp.181-182
• /
• 2003

경유엔진은 가솔린엔진에 비해 연소특성상 연료소비효율이 우수하여 온실가스인 $CO_2$ 배출이 적은 반면 대기 및 인체위해성이 높은 NOx와 입자상물질(PM)의 배출이 많아 대기저감을 위한 연료의 고압분사, 전자제어식 EGR기술등 엔진개량기술과 매연여과장치, De-NOx등 후처리기술 그리고 대체연료사용 기술등 다양한 저감대책이 전세계적으로 강구되고 있다. 특히 경유엔진에서 배출되는 오염물질로 인한 대기오염영향은 점차 증가하고 있어 대체연료사용 및 배출허용기준강화둥 우리 실정에 적합한 효율적인 대기저감대책이 강구되어야 할 것이다. (중략)

• Applied Chemistry for Engineering
• /
• v.20 no.4
• /
• pp.355-362
• /
• 2009

Fuels based on petroleum will eventually run out in the near future. DME (Di-methyl Ether) is a clean energy source that can be manufactured from various raw materials such as natural gas, coal as well as biomass. As DME has no carbon-carbon bond in its molecular structure and is an oxygenate fuel, its combustion essentially generates no soot as well as no SOx. Because the physical properties of DME are similar to those of LPG, the LPG distribution infrastructure can be converted to use with DME. DME has such high cetane number of 55~60 that it can be used as a diesel engine fuel. Practical use of DME as a next-generation clean fuel or next-generation chemical feedstock is advancing in the fields of power generation, diesel engines, household use, and fuel cells, among others. The purpose of this paper is review the characteristics, standardization, status of research and development in domestic and foreign countries of DME.

• Journal of Energy Engineering
• /
• v.24 no.2
• /
• pp.144-153
• /
• 2015

At low temperature, Wax build-up and settling can affect adversely the cold weather performance of the diesel vehicle. In this study, we test the cold properties of diesel by blending ratio of biodiesel, kerosene and WAFI. Also, we test the cold weather performance for diesel vehicle by fuel cold properties. Cold properties of diesel are improved by adding the WAFI, kerosene and get worse by adding the biodiesel. WAFI is effective to improve a cold filter plugging point(CFPP) and Kerosene is effective to improve a cloud point(CP). CFPP and pour point(PP) are related to cold weather performance of diesel vehicle but CP is unrelated. CFPP indicate a limit temperature of vehicle driving possibility.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.4
• /
• pp.140-146
• /
• 2010

An experimental study was carried out to investigate the emission characteristics for various alternative fuels in a 2.0 liter 4-cylinder turbo-charged diesel engine. The conventional diesel fuel, neat GTL (Gas to Liquid), blends of diesel and biodiesel(BD20), and blends of GTL and biodiesel(G+BD20 and G+BD40) were applied, and their emission characteristics were compared at various steady-state engine operating conditions. A noticeable reduction of exhaust emissions compared to conventional diesel fuel, except for NOx emission, was observed for G+BD40, where there is a maximum 30% averaged reduction for gaseous emissions (THC and CO) and 70% for PM mass concentrations. When comparing PM size distributions for biodiesel blended fuels, the PM number concentration in accumulation mode, where the diameter of PM is greater than 50 nm, decreased due to additional oxygen content in the biodiesel fuel; in nucleation mode, where the diameter of PM is less than 50nm, there was a slight increase or decrease in the PM number concentration depending on the amount of oxygen available in the combustion chamber.

• Korean Journal of Microbiology
• /
• v.50 no.4
• /
• pp.313-318
• /
• 2014

The world is in need of sustainable and eco-friendly energy sources such as microalgal biodiesel due to global warming and fossil fuel shortages. In this study, we compared the effectiveness of liquid fertilizer produced from swine manure and agriculture grade solid fertilizers as nutrient sources for microalgal biomass production. Mixed culture (Chlorella spp., Scenedesmus spp., Stigeoclonium spp.; CSS) was cultivated for 28 days in Small Scale Raceway Pond (SSRP) using various nutrient sources (swine manure liquid fertilizer, agricultural solid fertilizer, and mixture of these two fertilizers). Biomass and lipid productivity of fertilizer mixture were the highest at 0.8 g/L and 5.8 mg/L/day, respectively. These results indicate that the fertilizer mixture can provide microalgae necessary nutrient sources for stable biodiesel production and biomass growth. In addition, overall cost of microalgal cultivation and subsequently biodiesel production would be significantly reduced.

• Journal of Energy Engineering
• /
• v.16 no.2
• /
• pp.83-92
• /
• 2007

In view of stringent environment regulations to control the emission of green house gases and also depleting fossil fuel reserves, it is high quality desirable to develop alternative technologies to produce high quality fuels. To this end Biomass to Liquid (BTL) technology has received much attention in recent years. BTL process generally consists of gasification of biomass to produce bio-syngas, cleaning and control of $H_{2}/CO$ mole ratio of bio-syngas and Fischer-Tropsch synthesis & upgrading systems. Choren, Germany has first developed the commercial BTL process using unique gasification system i.e., Carbo-V. A new technology to remove tars and BTX has been developed by ECN in Netherlands employing a gasification system combined with OLGA technology. Several other countries including USA and Japan are showing great interest in BTL technology. Thus in view of our national energy security and also the environmental regulations, it is essential to develop alternative technologies like BTL in order to meet the increasing demand of energy though our insufficient biomass resources. In this paper we present an overview and development status of BTL-diesel technology.

• Journal of the Society of Disaster Information
• /
• v.19 no.3
• /
• pp.532-544
• /
• 2023

Purpose: To identify and evaluate the risk of chemical fire causative substances by using thermal analysis methods (DSC, TGA) for the hazards and physical property changes that occur when newly used biofuels are mixed with existing fuels It is to use it for identification and evaluation of the cause of fire by securing data related to the method and the hazards of the material according to it. Method: The research method used in this experiment is the differential scanning calorimeter (DSC: Difference in heat flux) through quantitative information on the caloric change from the location, shape, number, and area of peaks. flux) was measured, and the weight change caused by decomposition heat at a specific temperature was continuously measured by performing thermogravimetric analyzer (TGA: Thermo- gravimetric Analyzer). Result: First, in the heat flux graph, the boiling point of the material and the intrinsic characteristic value of the material or the energy required for decomposition can be checked. Second, as the content of biodiesel increased, many peaks were identified. Third, it was confirmed through analysis that substances with low expected boiling points were contained. Conclusion: It was shown that the physical risk of the material can be evaluated by using the risk of biodiesel, which is currently used as a new energy source, through various physical and chemical analysis techniques (DSC + TGA).In addition, it is expected that the comparison of differences between test methods and the accumulation and utilization of know-how on experiments in this study will be helpful in future studies on physical properties of hazardous materials and risk assessment of materials.