• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.14 no.2
• /
• pp.169-178
• /
• 2016

The properties of wastes for melting need to be considered to minimize the maintenance of refractory and to discharge the molten slags smoothly from a plasma torch melter. When the nonflammable wastes from nuclear facilities such as concrete debris, glass, sand, etc., are melted, they become acid slags with low basicity since the chemical composition has much more acid oxides than basic oxides. A molten slag does not have good characteristics of discharge and is mainly responsible for the refractory erosion due to its low liquidity. In case of a stationary plasma torch melter with a slant tapping port on the wall, a fixed amount of molten slags remains inside of tapping hole as well as the melter inside after tapping out. Nonmetallic slags keep the temperature higher than melting point of metal because metallic slags located on the bottom of melter by specific gravity difference are simultaneously melted when dual mode plasma torch operates in transferred mode. In order to minimize the refractory erosion, the compatible refractories are selected considering the temperature inside the melter and the melting behavior of slags whether to contact or noncontact with molten slags. An acidic refractory shall not be installed in adjacent to a basic refractory for the resistibility against corrosion.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.2
• /
• pp.177-183
• /
• 2005

The effluent quality is directly affected by the separation of biological solids in a final clarifier because the majority of discharged $BOD_5$ and SS are virtually dependent on the results of biological solids in the sedimentation tank effluent. If a final clarifier is effectively designed and operated, the desired goal of clarification for wastewater can be achieved together with the cost reduction in the treatment of wastewater. To this end flow characteristics and the removal efficiency of SS are numerically investigated especially by the change of the inlet position and the installation of baffle to improve the performance of a rectangular final clarifier. The 2-D computer program developed in a rectangular coordinates has been successfully validated against experimental residence time distribution(RTD) curves obtained by tracing radio-isotope. The lowering of the inlet position weakens the density current and induces the settling of SS in the front zone of a clarifier. Thus the decreased traveling distance of the sludge increases the removal efficiency of SS in the effluent. The inlet baffle installed in the front region of clarifier prevents the short circuiting flow and induces to flow into the dense underflow, which eventually improves the effluent quality. In the case of lower inlet position, however, installation of baffle results in degradation of effluent quality. Consequently it is strongly recommended that in-depth numerical study be performed in advance for optimizing a clarifier design and retrofitting to improve effluent quality in a final clarifier.

• Journal of the Korea Concrete Institute
• /
• v.29 no.1
• /
• pp.43-51
• /
• 2017

As per current seismic design codes, diagonally reinforced coupling beams are restricted to coupling beams having aspect ratio below 4. However, a grouped diagonally reinforcement detail makes distribution of steel bars in the beam much harder, furthermore it may result in poor construction quality. This paper describes the experimental results of concrete coupling beam reinforced with high-strength steel bars (SD500 & SD600 grades). In order to improve workability for fabricating coupling beams, a headed large diameter steel bar was used in this study. Two full-scale coupling beams were fabricated and tested with variables of reinforcement details and aspect ratio. To reflect real behavior characteristic of the beam coupling shear walls, a rigid steel frame system with linked joints was set on the reaction floor. As a test result, it was noted that cracking and yielding of reinforcement were initially progressed at the coupling beam-to-shear wall joint, and were progressed to the mid-span of the coupling beam, based on the steel strain and failure modes. It was found that the coupling beams have sufficient deformation capacity for drift ratio of shear wall corresponding to the design displacement in FEMA 450-1. In this study, the headed horizontal steel bar was also efficient for coupling beams to exhibit shear performance required by seismic design codes. For detailed design for coupling beam reinforced with high-strength steel, however, research about the effect of variable aspect ratios on the structural behavior of coupling beam is suggested.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.15 no.6
• /
• pp.118-126
• /
• 2011

The objective of this paper is to study the structural behavior of Composite Basement Wall (CBW) according to shear span-to-depth ratio through an experiment and predict the nonlinear behavior of CBW by using ADINA program widely has been being used for FE analysis. Especially, this study focuses on the part of CBW in which the Reinforced Concrete (RC) is under compression stress; At the region of CBW around each floor, RC part stresses by compressive force when lateral press by soil acts on the wall. The contact condition between RC wall and steel (H-Pile) including stud connector is main factor in the analysis since it governs overall structural behavior. In order to understand the structural behavior of CBW whose RC part is under compressive stress, an experimental work and finite element analysis were performed. Main parameter in the test is shear span-to-depth ratio. For simplicity in analysis, reinforcements were not modeled as a seperated element but idealized as smeared to concrete. All elements were modeled to have bi-linear relation of material properties. Three type of contact conditions such as All Generate Option (AGO), Same Element Group Option with Tie(SEGO-T) and Same Element Group Option with Not tie(SEGO-NT) were considered in the analysis. For each analysis, the stress flow and concentration were reviewed and analysis result was compared to test one. From the test result, CBW represented ductile behavior by contribution of steel member even if it had short shear span-to-depth ration which is close to "1". The global composite behavior of CBW whose concrete wall was under compressive stress could be predicted by using contact element in ADINA program. Especially, the modeling by using AGO and SEGO-T showed more close relation on comparing with test result.

• Applied Microscopy
• /
• v.29 no.1
• /
• pp.11-23
• /
• 1999

Ultrastructure of the ependymal cells of X-irradiated rats on their head were studied. Rats weighing $200\sim250gm$ were X-irradiated on their head and neck areas. Total exposures were 3,000 rads or 6,000 rads depending on experimental groups. And irradiated rats were sacrificed on 6 hours, 2 days and 6 days following the radiation exposures. Animals were perfused through the heart with 1% glutaraldehyde-1% paraformaldehyde solution, under ether-anesthesia. The tissues from the wall of lateral ventricles were fixed in the 2% osmium tetroxide solution. The results observed with electron microscope were as follow: 1. In 6 hours group, many ependymal cells were swelled, luminal portions of cytoplasms of some cells protruded into the ventricular lumen, and many cilia were lost or irregularly altered. 2. In 2 days group, ependymal cells were swelled more severely and subependymal edema were pronounced. 3. Protruded cytoplasm contained usually basal bodies of cilia, groups of mitochondria, endoplasmic reticula , etc. 4. Following X-irradiations, some protruded masses contained neural elements including the axon terminals with dense core vesicles. Axons and axon terminals were also found in the enlarged intercellular spaces among ependymal cells. From the above results, the heavy irradiation on the head area of the rat induced alteration of the ependymal cells lining the lateral ventricle. Hence the ependymal functions of selective barrier, protective barrier, and metabolic barrier could be altered following X-irradiation on the head.

• Applied Microscopy
• /
• v.29 no.1
• /
• pp.105-124
• /
• 1999

Histological and ultrastructural differentiations of the neuroepithelial cells in the mouse embryo during neurulation were observed. The neural plates and grooves consisted of pseudostratified columnar epithelium in the embryonic day (ED) 8 embryo were developed. In the ED 9 embryo, the neural tube was developed in all body length of embryo except both the cephalic and caudal ends. Secondary neurulation was shown at the tail bud of the ED 10 embryo. In the ED 8 embryo, the primitive streak was shown in the posterior end of the embryonic disc. The neuroepithelium, notochord and mesenchyme were well differentiated in the cephalic and cervical portions. In the ED 9 and 10 embryos, the roof plates of neural tubes were constituted of the closing of the surface ectodermal cells in the hindbrain and the neuroepithelial cells in the spinal cord. The floor plate of neural tube were consisted of the low pseudostratified columnar epithelium. The spinal motor nerve fibers were initially differentiated in the ED 10 embryo. According to the electron density of the cell and the differentiation of tell organelles, the neuroepithelial cells in the ED 9 and 10 embryos were classified into three types: dark, intermediate and light types. All types in the ED 9 embryo were observed but the dark cell in the ED 10 embryo was not done. The free ribosomes and polysomes in all neuroepithelial cells were developed. The RER and lipid droplets in the dark cell and the Golgi complex in the intermediate and light cells were observed. Many microfilaments in the cytoplasmic processes of intermediate cell and the microfilaments and microtubules in the light cell processes were observed to be well differentiated.

• Journal of the Society of Disaster Information
• /
• v.15 no.4
• /
• pp.479-492
• /
• 2019

Purpose: The purpose of this study is to accurately analyze the damage of bridges in order to determine whether fire bridges can be used continuously or to provide information on maintenance augmentation data. Method: XRD, SEM and EDS analyzes of concrete were carried out to estimate the fire temperature transferred to the structure, and analyzed by depth and area from PSCI beam and bottom plate concrete surface. Results: Test results G_12,11 for the fire zone concrete were confirmed to be affected by heat up to depth of 60mm and the temperature of the hydrothermal heat was above 1000℃. Also, the girder G_10,9,8 was relatively weakly damaged compared to G_12,11, and the degree of damage was confirmed to be affected by heat up to a depth of 40 mm. Conclusion: Based on the analyzed data, it is considered that if the repair / reinforcement and periodic inspection are carried out, the bridge can secure sufficient safety even considering the damage caused by the fire.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.299-299
• /
• 2007

후막형 무기 EL (electro-luminescence) 소자는 제조공정이 간단하고, 얇고, 가볍고, 유연한 동의 많은 장점들 때문에 휴대폰의 키패드 (key-pad) 및 광고용 back-light용으로 사용되고 있다. 이 무기 EL 소자는 비교적 손쉬운 스크린 프린팅 (screen-printing) 법으로 대면적을 제작할 수 있지만, LED (light emitting diode) 등과 비교하여 밝기가 낮아서 그 응용 분야가 제한되고 있다. EL 소자의 형광층은 전면 전극과 후면 전극 사이에 위치한다. EL은 이 형광층에 고 전기장이 걸릴 때, 전기장에 의해 가속된 전자가 형광층 내부에 첨가된 발광 중심의 전자를 여기시키고, 여기된 전자가 다시 바닥상태로 완화될 때 빛이 방출되는 현상이다. 즉, EL 소자는 이러한 전자 발광 현상을 이용한 소자로서, 전압 인가 시 발광 면 전체가 균일하게 발팡하는 평면 광원이다. 이러한 EL 소자에서 휘도의 증가는 후면 전극과 형광층 사이에 삽입되는 유전체 층의 특성과 밀접한 연관성이 있다. 본 연구에서는 고휘도 무기 EL 소자를 제작하기 위하여 이 유전체 층의 특성과 소자의 성능 사이의 관계를 알아보고자 하였다. 유전체 층에 사용하기 위해서 $BaTiO_3$-PVDF (polyvinylidene fluoride)의 복합체 필름을 제조하였다. 먼저 이 복합체 필름을 스크린 프린팅 (screen printing) 법으로 코팅하기 위한 페이스트 제작을 위해서, PVDF 수지를 용제에 녹였다. 그 다음, 일반 혼합기 및 삼단 롤밀 혼합기 (3-roll milling mixer) 등을 이용하여 $BaTiO_3$ 분말과 PVDF 용액을 다양한 비율로 혼합하여 페이스트를 제조하였다. ITO가 증착된 PET Film에 스크린 프린팅 법을 사용하여 형광층, 유전층, 배면 전극 등을 차례로 코팅하였다. $BaTiO_3$ (BT) 분말과 복합체 필름의 XRD 분석 결과, 분말 시료와 복합체 시료 모두 페로브스카이트 구조의 BT 회절선만 관찰되었다. 복합체의 단면 SEM 관찰에서는, BT 분말의 무게비가 증가할수록 더 치밀한 구조를 보여줌을 확인하였다. 또 EL소자의 유전상수와 휘도도 BT 분말의 혼합비가 증가할수록 증가하였다. 본 연구에서 제작한 무기 EL 소자의 최대 휘도는 약 $130\;cd/m^2$ 정도로 측정되었는데, 이는 휴대폰 키패드의 back-light용 광원으로 사용하기 충분하다고 판단되어진다.

• Journal of the Mineralogical Society of Korea
• /
• v.30 no.4
• /
• pp.161-172
• /
• 2017

Clay minerals play a major role in the geochemical cycles of metals in the Critical Zone, the Earth surface-layer ranging from the groundwater bottom to the tree tops. Atomistic scale research of the very fine particles can help understand the fundamental mechanisms of the important geochemical processes and possibly apply to development of hybrid nanomaterials. Molecular dynamics (MD) simulations can provide atomistic level insights into the crystal structures of clay minerals and the chemical reactivity. Classical MD simulations use a force field which is a parameter set of interatomic pair potentials. The ClayFF force field has been widely used in the MD simulations of dioctahedral clay minerals as the force field was developed mainly based on dioctahedral phyllosilicates. The ClayFF is often used also for trioctahedral mineral simulations, but disagreement exits in selection of the interatomic potential parameters, particularly for Mg atom-types of the octahedral sheet. In this study, MD simulations were performed for trioctahedral clay minerals such as brucite, lizardite, and talc, to test how the two different Mg atom types (i.e., 'mgo' or 'mgh') affect the simulation results. The structural parameters such as lattice parameters and interatomic distances were relatively insensitive to the choice of the parameter, but the vibrational power spectra of hydroxyls were more sensitive to the choice of the parameter particularly for lizardite.

• Korean Journal of Remote Sensing
• /
• v.22 no.6
• /
• pp.621-626
• /
• 2006

Today's commercial high resolution satellite imagery such as IKONOS and QuickBird, offers the potential to extract useful spatial information for geographical database construction and GIS applications. Extraction of 3D building information from high resolution satellite imagery is one of the most active research topics. There have been many previous works to extract 3D information based on stereo analysis, including sensor modelling. Practically, it is not easy to obtain stereo high resolution satellite images. On single image performance, most studies applied the roof-bottom points or shadow length extracted manually to sensor models with DEM. It is not suitable to apply these algorithms for dense buildings. We aim to extract 3D building information from a single satellite image in a simple and practical way. To measure as many buildings as possible, in this paper, we suggested a new way to extract building height by triangular vector structure that consists of a building bottom point, its corresponding roof point and a shadow end point. The proposed method could increase the number of measurable building, and decrease the digitizing error and the computation efficiency.