• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1332-1336
• /
• 2005

It could make the LIghtweight Piezoelectric Composite Actuator (LIPCA) damageable by the cyclic large deformation. If the progressive microvoid coalescence of LIPCA interlaminar took place, the decrease of the stiffness and the weakness of stress transmission and fiber bridging effect would make the fatigue characteristics worse suddenly. Therefore, it is required to study the variation of fatigue behavior and interlaminar condition in LIPCA under resonant frequencies. These studies such as the changeable fatigue phase and interlaminar behavior of LIPCA affected by the resonant frequencies should be carried out due to the strong anisotropy of CFRP layer. Hence, these studies are as follows. 1) The residual stresses distribution of interlaminar in LIPCA using the Classical Lamination Theory (CLT). 2) Comparative analysis of interlaminar behavior for the intact LIPCA versus LIPCA containing an artificial delamination during resonant frequency.

• 한국재료학회지
• /
• 제20권11호
• /
• pp.581-585
• /
• 2010

High strength sheet steels for automobile are seriously compromised by hydrogen embrittlement. This issue has been continuously studied, but the field of interest, which lies between microstructural characteristics and hydrogen behavior with hydrogen charging, has not yet been thoroughly investigated. This study was done to investigate the behavior of hydrogen according to the hydrogen volume fraction on 590MPa grade DP steels, which are developed under hydrogen charging conditions as high strength sheet steels for automobiles. The penetration depths and the mechanical properties, according to charging conditions, were investigated through the distribution of micro-hardness and the microstructural observation of the subsurface zone. It was found that the amount of hydrogen trapping in 590MPa DP steels was related to the austenite volume fraction. It was confirmed that the distribution of micro-hardnesses according to the depth of the subsurface zone under the free surface showed the relationship of the depth of the hydrogen saturation between the charging conditions.

• 한국전기전자재료학회논문지
• /
• 제23권9호
• /
• pp.741-746
• /
• 2010

Three-dimensionally ordered macro-porous Sn-C composites were prepared by using polystyrene microsphere as a template. The Sn-C composites were composed of well-interconnected pore with circular shape and wall structure with wall thickness of a few tens of nano-meters. This porous three-dimensional structure is readily and uniformly accessible to the electrolyte, which facilitates lithium ion diffusion during charge-discharge reactions. The wall thickness of the composites was increased as the increase of Sn content of the composite. From EDS analysis, it is confirmed that the Sn was dispersed uniformly in Sn-C composites. The capacity was increased as the Sn content increased, which is due to Sn anode with high capacity. The Sn-C composites with high Sn content showed superior cyclic performances. Such enhancement is ascribed to the thick wall thickness and small pore size of the sample with high Sn content. The Sn-C composite with Sn 30 wt% showed relatively high capacity and stable cycle life, however, the stability of the 3-dimensional structure should be enhanced by further work.

• 한국전기전자재료학회논문지
• /
• 제18권10호
• /
• pp.960-964
• /
• 2005

In this paper, we dealt with a partial discharge(PD) measurement method that has been accepted as an effective and non-destructive technique to estimate insulation performance of low-voltage electric and electronic devices. The PD measurement system Is composed of a coupling network, a low noise amplifier, and associated electronics. h shielded box Is adopted to make a better measurement environment against around noise. A low cut-off frequency of the coupling network estimated by a sinusoidal wave input was 125 kHz (-3 dB). Calibration tests on laboratory set-up have shown that the PD measurement system has a stable sensitivity of 10 mV/pC. In an application test oil a low-voltage three phase Induction motor (5 HP), we could detect 0.53 pC level of partial discharge at the applied voltage of AC 650 $V_{peak}$.

• 한국재료학회지
• /
• 제12권6호
• /
• pp.447-451
• /
• 2002

Pulsed DC-plasma nitriding has been applied to form nitride layer having only a diffusion layer. The discharge current with the variation of discharge gases is proportional to the intensity of $N_2^+$ peak in optical emission spectroscopy during the plasma nitriding. The discharge current, microhardness in surface of substrate and depth of nitride layer increased with the ratio of $N_2\;to\;H_2$ gas in discharge gases. When the ratio of $N_2\;to\;H_2$ is lower than 60% in the discharge gases, high microhardness value of 1100Hv nitride layer which contains no compound layer has been formed.

• 한국재료학회지
• /
• 제8권1호
• /
• pp.27-32
• /
• 1998

In-Sit반응소결에의해 Si과 AI금속분말을 이용하여 Si$_{3}$N$_{4}$-AIN 복합세라믹스를 합성하였다. 합성된 Si$_{3}$N$_{4}$-AIN복합세라믹스의 미세조직과 결정구조를 해석하기 위해, OM, TEM, XRD및 EDX를 이용하였으며, Si$_{3}$N$_{4}$-AIN -20wt.%AIN복합세라믹스에서 Si의 질화율은 97%로 가장 높았다. Si$_{3}$N$_{4}$-AIN 복합세라믹스에서 Si의 질화율은 AI첨가량 증가에 따라 감소하였다. 대부분의 AI입자들은 다결정 AI입자들은 다결정 AIN(4-H구조)로 완전질화되었으며, 따라서 잔류 AI상은 반응소결체내에서 관찰되지 않았다. Si$_{3}$N$_{4}$의 결정구조는 $\alpha$와 $\beta$구조가 혼재된 상태이며, 잔류 Si입자내에서는 미소균열 및 전위가 관찰되었다. AI/Si$_{3}$N$_{4}$와 Si$_{3}$N$_{4}$ 두계면에서 이들은 거친 형상을 보이지만, 계면반응상은 관찰되지 않았다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.193-193
• /
• 2008

Wearable and ubiquitous micro systems will be greatly growing and their related devices should be self-powered in order to avoid the replacement of finite power sources, for example, by scavenging energy from the environment. With ever reducing power requirements of both analog and digital circuits, power scavenging approaches are becoming increasingly realistic. One approach is to drive an electromechanical converter from ambient motion or vibration. Vibration-driven generators based on electromagnetic, electrostatic and piezoelectric technologies have been demonstrated. Among various generator types proposed so far, piezoelectric generator possesses considerable potential in micro system. To overcome low mechanical-to-electric energy conversion, the piezoelectric device should activate in resonance mode in response to external vibration. Normally, the external vibration excretes at low frequency ranging 0.1 to 200 Hz, whereas the resonant frequencies of the devices are fixed as constant. Therefore, keeping their resonant mode in varying external vibration can be one of important points in enhancing the conversion efficiency. We investigated the possibility of use of multi-bender type piezoelectric devices. To match the external vibration frequency with the device resonant frequency, the various devices with different resonant frequency were chosen.

• 한국재료학회지
• /
• 제27권9호
• /
• pp.459-465
• /
• 2017

Nano-sized Zinc selenide (ZnSe) powder was successfully synthesized using Zn and Se precursors in a hydrothermal process. Temperature for the synthesis was varied from $95^{\circ}C$ to $180^{\circ}C$ to evaluate its influence on the microstructural properties of the synthetic particles. ZnSe powder thus fabricated was characterized using various analytical tools such as SEM, XRD, TEM and UV-Vis methods. Two types of ZnSe particles, that is, the precipitated particle and the colloidal particles, were identified in the analysis. The precipitated particles were around 100 nm in average size, whereas the average size of the colloidal particles was around 20 nm. The precipitated particles made at $150^{\circ}C$ and $180^{\circ}C$ were found to be a single phase of ZnSe; however, an inhomogeneous phase was obtained at the lower synthesis temperature of $95^{\circ}C$, suggesting that the temperature for the synthesis should be over $100^{\circ}C$. The precipitated particles were inactive in the UV-Vis absorption investigation, whereas the colloidal particles showed that absorptions occurred at 380 nm in the UV-Vis spectrum.

• 한국재료학회지
• /
• 제9권10호
• /
• pp.1000-1005
• /
• 1999

Zr-0.8Sn합금의 재결정에 미치는 V, Sb의 영향을 조사하기 위해 냉간 압연 후 여러 온도 조건에서 열처리된 시편의 미세조직을 편광광학현미경, SEM, TEM으로 관찰하였고 미소경도계로 경도값을 측정하였다. 미세조직을 관찰한 결과 V과 Sb의 첨가에 의해 재결정이 지연되었으며, 재결정 완료 후의 결정립 성장도 억제됨이 관찰되었다. 특히 Sb는 V보다 재결정을 완료하는데 필요한 온도를 상승시키므로 재결정을 지연시키는 효과가 더욱 큰 것으로 생각된다. 이 처럼 첨가원소가 증가함에 따라 재결정에 늦어지고 결정립이 미세화 되는 것은 V이나 Sb 첨가에 의해 형성된 석출물이 전위나 입계의 이동을 방해하기 때문인 것으로 사료된다.

• 한국재료학회지
• /
• 제3권5호
• /
• pp.451-458
• /
• 1993

베아링강(AISI S2100) 위에 TiCi/sub 4/, N/sub 2/,H/sub 2/,그리고 Ar의 기체혼합계를 이용하여 플라즈마화학증착법으로 내마모 TiN증착층을 얻었다. 증착된 TiN층 내의 잔류 CI에 의한 결정성, 미소경도, 접착력, 그리고 마모특성에 대해 연구하였다. TiN 중착층은 좋은 내마모성을 가지고 있었으며, TiN의 기계적 특성은 잔류CI함량이 증가할때 나빠졌다. 마모측정결과 마모면의 trailing edge에 인장응력이 걸려 많은 crack이 관찰되엇다.