• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.11a
• /
• pp.249-254
• /
• 2004

광의 효율적 사용을 위해 표면에 마이크로 그루브가 새겨진 고성능 광학 부품의 개발이 활발하고, 이들 부품의 다량 생산을 위한 초정밀 금형제조기술이 각광을 받고 있다. 최근의 초정밀 미세 기계가공의 경우 간단한 공정으로 이러한 마이크로 그루브 금형을 제작할 수 있다. 특히 조명각 변조용 렌티큘러 렌즈와 같이 실린더형 그루브 금형의 경우에는 기존의 Lithography, MEMS, LIGA 등 광 에너지를 이용한 다른 제조방법들에서는 가공하기 어려운 점이 있으나, 기계가공에서는 쉽게 제작가능한 장점이 있다. 본 연구에서는 이러한 미세기계가공기술의 장점을 활용하여 U 형 마이크로 그루브를 가진 Lenticular 렌즈용 금형을 가공하고자 하였다. 가공에는 3 축 구동의 초정밀 미세 복합가공기와 단결정 천연 다이아몬드공구가 사용되었고, 가공방식은 마이크로 세이핑 공정을 적용하였으며, 가공 금형 재료에는 Brass와 무전해 Nickel이 사용되었다. 실험을 통하여 금형가공시의 절삭력, 칩 형상, 가공표면 등의 분석이 수행되었으며 이를 기반으로 여러 가지 가공문제점을 해결하고, 최종적으로 양호한 렌티큘러렌즈용 금형을 가공하였다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.3
• /
• pp.313-318
• /
• 2013

Magnetic abrasive polishing is an advanced deburring process for nonmagnetic materials and micropattern products that have non-machinability characteristics. Despite these advantages, there are some problems with using MAP for deburring. MAP has introduced geometric errors into microgrooves because of an over-cutting force caused by uncontrolled magnetic abrasives in the MAP tool. Thus, in this study, to solve this problem, an EP (electrolyte polishing)-MAP hybrid polishing process was developed for deburring microgrooves in an STS316 material. In addition, an evaluation of EP-MAP for the deburring of microgrooves was carried out by profiling the burrs. The results of the experiment showed geometric errors after the deburring process using MAP. However, in the case of EP-MAP, no geometric error was observed after the process because of the lower material removal rate in EP-MAP.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.12
• /
• pp.1641-1646
• /
• 2011

The second-generation magnetic abrasive polishing is one of the nontraditional machining technologies newly developed. Because of the flexibility effect in magnetic abrasive polishing, the precise and mirror like surface can be obtained during this process. In this study, magnetic abrasive polishing process was applied in small grooved surface. As a result, it was seen that the flexible magnetic abrasive tool was effective to remove burrs on the edge of the groove. However, the efficiency of magnetic abrasive polishing at the slot was very low according to increasing depth and width of slot. So, correlation between geometric parameters, such as the depth and width, and surface roughness was evaluated and the minimum width for suitable polishing was found by experimental results.

• Proceedings of the Korea Contents Association Conference
• /
• 2017.05a
• /
• pp.489-490
• /
• 2017

골유착은 비골조직의 삽입없이 뼈와 금속간의 직접적인 접합으로 치과 임플란트나 정형외과적 기구의 임상적 성공여부를 판가름 짓는 중요한 요소이다. 현재까지 골유착을 향상시킨다 알려진 패턴은 일부 알려져 있지만, 표면패턴이 제한적이라 기대만큼 큰 발전을 이루지 못했다. 본 연구는 특정 그루브 패턴이 조골세포의 분화를 조절할 수 있음을 보여주면, 특정 패턴에서 조골세포의 분화를 강화시킬 수 있다는 계념은 치과의 임플란트나 정형외과 의료기기에 개발에 중요한 기초를 제공할 수 있으리라 사료된다.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.11
• /
• pp.47-54
• /
• 2003

Research during the past several years has established the effectiveness of acoustic emission (AE)-based sensing methodologies for machine condition analysis and process. AE has been proposed and evaluated for a variety of sensing tasks as well as for use as a technique for quantitative studies of manufacturing process. STD11 has been known as difficult-to-cut materials. The micro-grooving machine was developed for this study and the experiments were performed using CBN blade for machining STD11. Evaluating the machining conditions, frequency spectrum analysis of acoustic emission (AE) signals according to each conditions were applied. Fuzzy clustering method for associating the preprocessor outputs with the appropriate decisions was followed by frequency spectrum analysis. FFT is used to decompose AE signal into different frequency bands in time domain, the root mean square (RMS) values extracted from the decomposed signal of each frequency band were used as features.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.8 s.251
• /
• pp.957-964
• /
• 2006

As the requirement of LCD products which are large screen and have high brightness increases, the role of light guide panel (LGP) of which micro-features diffuse the light uniformly on surface is getting important. In general, there are many errors in machining like machine tool errors process error, setup error and etc. The amount of setup error in general machining is not so big in comparison with the others, so it is mostly neglected. But, especially in v-groove micromachining, setup error has a significant effect on micro-features. Low quality product and high cost are resulted from setup error. In v-groove micromachining, to confirm the effect of setup error, it is identified and then setup error synthesis model is derived from analysis of tool and workpiece setup. In addition, to predict the micro-features affected by setup error and enhance the production efficiency, the setup condition satisfying the tolerance of micro-features is geometrically analyzed and presented.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.02a
• /
• pp.231-238
• /
• 2002

미세 절삭에 의한 마이크로 형상가공 및 이를 이용한 미세금형 가공기술개발을 위하여 절삭 공구를 이용한 기계적 미세 가공법에 대한 고찰과 더불어 shaping, end-milling, drilling 등의 가공이 가능한 기계적 미세 가공시스템을 구성하고 이를 이용한 미세 치형 그루브와 미세 격벽 등 미세 형상 구조의 금형 개발을 위한 가공실험을 수행하였다. 본 실험에서는 먼저 shaping 방식으로 세 종류의 다이아몬드 바이트를 사용하여 알루미늄, PMMA, Nickel, 황동 등의 소재에 pitch $150{\mu}m$, 높이 $8{\mu}m$ 내외의 미세 치형의 금형 코어를 가공하였고, 다음으로 Z축에 air spindle을 설치하여 $\phi0.2mm$의 end-mill(WC)을 사용하여 황동 소재에 깊이 $200{\mu}m$, 폭 $200{\mu}m,\;100{\mu}m,\;50{\mu}m,\;30{\mu}m$의 두께 변화를 주어 미세 격벽에 대한 가공실험을 하였다. 미세 구멍가공실험으로는 drilling 전용장비를 구성하여 $\phi0.6\~0.15mm$의 drill공구로 SM45C와 세라믹$(Si_3N_4-BN)$ 소재에 스텝이송방식에 의한 미세 구멍 가공 실험을 실시하였다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.97-100
• /
• 2004

In recent years, a demand for micro-structure machining is increasing by the development of information and optics industries. Micro machining technology is in general well known in the field of lithograghy. However, the requirement of producing micro machine and/or micro mechanism with metal materials will be increased since a variety of workpiece configurations can be easily made. In this paper, ultra precision machine is developed to obtain micro groove and mirror surface using single crystal diamond tool. According to the cutting experiment, no burr was found at the edge of V-grooves, and the surface roughness of copper is about 1～3nm Ra. It is verified that ultra precision machine is effective to high precision machining.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.04a
• /
• pp.263-268
• /
• 2001

The needs for precision machining of micro to milli parts have been increased as the industry require high quality products, especially for the micro-machining of IT products. The ultra-precision machining system is essential for the micro machining of fine structures, which insures machining accuracy, low systematic and random error and repeatability. In this study, we developed micro machining system, which is equipped with air bearing stage for ultra precision machining and also we present the results of V-grooving experiments, conducted by the developed system, to verify the performance of system. The results show that the machined V-grooving had good accuracy with repeatable stability.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.149-149
• /
• 2004

반도체 산업이 급속하게 발전함에 따라 고집적, 대용량이 요구되고 있으며, 이에 따라 선폭의 미세화, 웨이퍼 크기의 증가, 패턴의 다층화가 필수적인 조건으로 대두되고 있다. 이러한 요구를 만족시키기 위해서는 고정도의 표면상태와 칩과 웨이퍼 전면에서의 균일한 가공이 필요하다. 따라서 화학 기계적 연마를 통한 안정하고 고성능의 평탄화는 고집적 소자형성에 있어서 핵심 기술이 되고 있다.(중략)