• Journal of the Korean Geotechnical Society
• /
• v.17 no.3
• /
• pp.33-39
• /
• 2001

지진 등에 의해 유발된 동 하중에 의한 지반-구조물 계의 응답은 지반-구조물사이의 경계에서의 마찰특성과 미끄러짐에 의해 크게 영향을 받게 된다. 본 논문에서는 진동대(Shaking table)를 이용하여 조립토와 건설재료(steel)와의 경계에서 지반으로부터 지중구조물에 전달되는 전단응력의 전달정도를 파악하기 위한 실험을 실시하였다. 본 실험에서 설정한 미끄러짐속도 범위 내에서는 미끄러짐속도 변화에 따른 조립토와 건설재료(steel) 사이의 동마찰계수의 변화가 작다는 사실이 관찰되었다. 그리고 조립토의 평균유효입경의 변화가 동마찰계수에 미치는 영향도 함께 조사되었으며, 이 동마찰계수를 같은 조립토에 대한 평면변형률시험을 통해 얻어진 최대내부마찰각으로부터 구한 마찰계수와 비교하여 정량화하였다.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.03a
• /
• pp.461-468
• /
• 2001

지진등에 의해 유발된 동 하중에 의한 지반-구조물 계의 응답은 지반-구조물사이의 경계에서의 마찰특성과 미끄러짐에 의해 크게 영향을 받게 된다 본 논문에서는 진동대(Shaking table)를 이용하여 조립토와 건설재료(Steel)의 경계에서 지반으로부터 지중구조물에 전달되는 전단응력 의 전달정도를 파악하기 위한 실험을 실시하였다. 본 실험에서 설정한 미끌어짐속도 범위내에서는 미끄러짐속도 변화에 따른 조립토와 건설재료(Steel)사이의 동마찰계수의 변화가 작다는 사실이 관찰되었다. 그리고 조립토의 평균유효입경의 변화가 동마찰계수에 미치는 영향도 함께 조사되었다. 또한 이 동마찰계수를 같은 조립토에 대한 평면변형률시험을 통해 얻어진 최대내부마찰각으로부터 구한 마찰계수와 비교하여 정량화하였다.

• Tunnel and Underground Space
• /
• v.15 no.4 s.57
• /
• pp.288-295
• /
• 2005

Many mechanical defects originated from various geological causes make rock mass exhibit anisotropic characteristics. Understanding how the stress distribution occurs in anisotropic rock mass is, therefore, very important for the design of footings on rock and rock structures. In this study, the patterns of elastic stress distribution, developed by acting line load on the surface, in transversely isotropic was investigated. The influence of joint stiffness, joint spacing, and dip angle on the stress distribution was examined. By assuming the Mohr-Coulomb criterion as joint slip condition, the development of joint slip zone was also discussed.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.21 no.5
• /
• pp.515-524
• /
• 2008

The ultimate behavior of high-tension bolted joints with various plate thickness and bolt size is investigated using nonlinear F.E. analysis and experimental study. The relation with sliding load, bolt deformation, and failure modes are presented based on plate thickness and bolt size. Three kinds of the bolt diameter(M20, M22, M24) and five types of the steel plates (l2mm, 16mm, 20mm, 30mm, 40mm) are considered for the ultimate behavior of the bolted joints. The numerical model, constructed by commercial F.E. program, ABAQUS, of ultimate behavior of bolted joints is introduced and verified by experimental results. The force-displacement and force-axial strain relations are measured and compared with the results by 3D finite element analysis.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.2A
• /
• pp.327-338
• /
• 2006

Friction type high tension bolted joints is one of the most common steel structure connections and requires significant concerns on axial force of the bolts. However, its high shear capacity is not appropriately considered in design and hence the number of bolts is over-designed than actually required. It is primarily due to a slip-load-based design method. This study, therefore, suggests a new technology of connection using a shear ring, which may reduce the shortcomings from the friction-typed high tension bolted joints and maximize the advantages from the bearing-typed joints. Experimental and numerical studies were performed to compare the capacity of the suggested method with traditional high tension bolted joints. From the results, it is known that the suggested connections has higher bearing capacity than friction-typed high tension bolted joints due to the higher shear resistance from the ring. For further study, it may be necessary to investigate on design parameters including the depth of shear ring, for increased connection capacity.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.4 s.71
• /
• pp.407-414
• /
• 2004

Bridges in common use are expected to have more varieties of load in their connected members and bolts than in construction. Faults in connection members or bolts occur so often according to the time flow. One of the purposes of this study is to find out the behavior and structural features of high-tension bolted joints with faults that are very difficult and cost much to find out through experimentation with finite element analysis. Another purpose of this study is to provide sufficient data, estimated experimental results, and the scheme of the test plate for an economical experimental study in the future. Surveys of bridges with a variety of faults and statistical classifications of their faults were performed, as was a finite element analysis of the internal stress and the sliding behavior of standard and defective bridge models. The finite element analysis of the internal stress was performed according to the interval of the bolt, the thickness of the plate, the distance of the edge, the diameter of the bolt, and the expansion of the construction. Furthermore, the analysis explained the sliding behavior of high-tension bolt joints and showed the geometric non-linear against the large deformation, and the boundary non-linear against the non-linear in the contact surface, including the material non-linear, to best explain the exceeding of the yield stress by sliding. A normally bolted high-tension bolt joint and deduction of bolt tension were also analyzed with the finite element analysis of bridge-sliding behavior.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.12
• /
• pp.33-40
• /
• 2008

The load distribution and deformation of rock-socketed drilled shafts subjected to axial loads are evaluated by a load-transfer method. The emphasis is on quantifying the effect of coupled soil resistance in rock-socketed drilled shafts using the 2D elasto-plastic finite element analysis. Slippage and shear load transfer behavior at the pile-soil interface are investigated by using a user-subroutine interface model (FRlC). It is shown that the coupled soil resistance provides the influence of pile toe settlement as the shaft resistance is increased to an ultimate limit state. The results show that the coupling effect is closely related to the value of pile diameter over rock mass modulus (D/$E_{mass}$) and the ratio of total shaft resistance against total applied load ($R_s$/Q). Through comparisons with field case studies, the 2D numerical analysis reseanably presented load transfer of pile and coupling effect due to the transfer of shaft shear loading, and thus represents a significant improvement in the prediction of load deflections of drilled shafts.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.5C
• /
• pp.221-229
• /
• 2012

Steel ribs such as H-beam or lattice girder are often reinforced to secure the stability of NATM tunnel when the ground is in the bad condition. When designing, however, steel ribs are not often taken into consideration on the numerical analysis when they are regarded as temporary tunnel supports until shotcrete shows its best performance or if they are, there are various modeling methods. This study shows behavior and loading capacity of steel ribs and shotcrete through the strength test on the bending, pressure and full-scaled. Also, we conducted and analyzed the experiment of composite member consisting of shotcrete and steel ribs under the same condition. Through the result, we can find the fact that shotcrete and steel ribs do not work as one unit because of slipping on the boundary. Also, when numerical analyzing, it was concluded that steel ribs cover all bending moment and shotcrete and steel ribs share with axial force according to the compressive strength.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1992.10a
• /
• pp.90-96
• /
• 1992

경계면 요소를 이용하여 철근콘크리트 구조물의 접촉면 문제를 유한 요소법으로 해석하는 기법에 대하여 연구한다. 본 연구에서는 경계면 요소의 수치해석의 이론과정을 전개하고, 실험 관찰된 부착 시험체에 적용하여 이형철근과 콘크리트 부착기구의 접촉면을 해석한다. 경계면은 특별한 연결요소를 이용하여 재현하며 Mohr-Coulomb의 마찰 이론을 응응한다. 해석의 주요점으로 하중상태에 따라 변화되는 경계면의 접촉상태, 즉 고정(stick), 미끄러짐(slide), 분리(separation)를 묘사하여 경계면 재료의 비선형 거동을 관찰한다. 부착모델의 해석결과는 실험실의 결과와 대체로 일치되며 따라서 철근콘크리트 접촉면의 응력해석을 위해 경계면 요소가 활용될 수 있음을 보여준다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.2
• /
• pp.165-170
• /
• 2012

This paper contains the test method to obtain aerodynamic hinge moments acting on the control surface of air vehicle wing. During the flight, hinge moments make difference between actual control surface angle and control angle which is measured by sensor of actuator. The hinge moments can be obtained by using this difference. Static ground load test and calibration test were conducted to obtain torsional stiffness of control surface actuation system. This results are used to calculate hinge moments. In addition, the mechanical errors of actuation system such as slip angle of mounting point and backlash could be estimated. Using flight test results, this experimental measurement method of hinge moment acting on control surface is conducted. The results of this method are similar to those of numerical simulation method, and the validity of this method is proved.