• The Journal of Engineering Geology
• /
• v.13 no.3
• /
• pp.335-344
• /
• 2003

This study is focused to the physical and shear strength properties of the weathered limestone soils distributed in Changsung and Hwasun area, Chonnam province. Disturbed soil was used as soil samples. To grasp the physical and shear strength properties of weathered limestone soil, specific gravity test, atterberg limit, grain size distribution and direct shear test were conducted in the laboratory. The physical and shear strength properties of the weathered limestone soil in the study areas are as follows. The range of specific gravity (Gs) is 2.78 to 2.80, liquid limits (LL) 37 to 38 (%), plasticity index (PI) 13.7 to 15.4, and soil classification CL. The range of strength parameters by direct shear test (vd, $1.5t/\textrm{m}^3$) is 3.07 to 4.4 ($t/\textrm{m}^2$) of cohesion and 34.8 to $42.4^{\circ}$ of internal friction angle in unsaturated soils. As a result of comparing with the weathered granite soils (Yang, 1997: Mun, 1998: Park, 1998), it is considered that physical properties of the weathered limestone soils in this study are different from the weathered granite soils. On the other hand, internal friction angle of shear parameters is found to be similar.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.6C
• /
• pp.221-229
• /
• 2011

A core zone of a fill dam is an important part of a dam for cutoff of water. Therefore, the material properties and behavior characteristics of a core zone are very important factors in an analysis of dam stability. However, the investigation on material properties of actual dam core is extremely rare so far. The material properties have been acquired or estimated by indirect methods like a surface wave surveying or empirical equation. In this research, in-situ and laboratory tests were conducted during dismantling an existing dam directly to investigate characteristics of the core zone in terms of the depth and transient variation of properties after construction of the dam. Dynamic material properties like shear wave velocity and shear modulus were measured and compared to other existing empirical correlations. In addition, aging characteristics of dynamic material properties were investigated by a series of laboratory tests.

• The Korean Journal of Rheology
• /
• v.7 no.3
• /
• pp.173-180
• /
• 1995

LLDPE/LDPE 혼합물의 유변 물성과 필름가공특성 필름 물성 및 LLDPE의 extrudate 표면상태를 살펴보았다. LLDPE에 LDPE를 혼합함으로써 용융 강도가 크게 향상 되는 것을 볼수 있었으며 혼합비에 따라 필름의 기계적 물성이 변화하는 것을 볼수 있었다. 즉 최고의 물성을 나타내는 적절한 혼합비율이 존재하였다. 본논문에 사용된 LLDPE/LDPE 혼합물에 있어서는 LDPE의 함량이 15∼30wt%일 때 가장 우수한 기계적 물성을 얻을수 있 었다. LLDPE 필름의 표면 불량 문제를 보기위하여 capillary를 이용하여 LLDPE extrudate 의 표면 튀틀림(distortion)의 진행순서를 살펴본 결과, 전단 응력이 0.23MPa 일때 sharkskin이 발현함을 볼수 있었다.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.26 no.12
• /
• pp.1749-1755
• /
• 2002

본연구의 목적은DP가공에 의한 가교화를 통해 텐셀의 피브릴화를 조절할 때 DP가공 방법 및 NaOH전처리 효과를 물성, 표면형태, 역학적 성질 및 태의 변화의 관점에서 고찰하는데 있다. SEM 분석결과DP가공에 의해 피브릴 발생 정도는 감소하였다. DP가공 방법에 있어 서 WF법과 PDC법에 따른 물성의 차이는 나타나지 않았다. 역학적특성의 경우 DP가공은 DP가공 방법에 상관없이 효소처리한 직물의 인장선형성에는 큰 영 향을 주지 않았으나 인장에 너지, 굽힘 강성, 압축선형성, 압축 레질리언스, 기하학적 거칠기는 감소시켰고 인장 레질리언스, 굽힘이력, 압축에너지는 증가시켰다. 전단특성은 WF법에서는 증가한 반면, PDC법에서는 감소하여 DP가공 방법에 따른 차이를 나타내었다. WF법이 PDC법보다 더 높은 Koshi, Numeri, Fukurami 값을 보였으며, 종합태 값은 비슷하게 나타났다. NaOH 전처 리에 의해 수지부착량은 감소하였으나 감량률은 증가하였으며, DP성/물성은 더 낮게 나타났다. NaOH 전처리에 의해 인장선형성, 인장에너지, 압축 레질리언스, 전단 및 굽힘특성은 증가하였으나 인장레질리언스와 압축선형성, 압축에너지, 표면특성은 감소하였다. NaOH 전처리한 경우 Koshi는 증가하였고, Numrei와 Fukuramil는 감소하였으며, 종합태 값은 가장 낮았다. 처리한 시료들은 각각 다른 감성과 촉감을 나타냈다.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.26 no.12
• /
• pp.1685-1693
• /
• 2002

다양한 용도로 사용되고 있는 라미네 이 팅 직물은 주로 별도로 제조된 고분자 필름 또는 막을 접착제, 열, 압력 등을 이용하여 기포(基布)와 결합시키는 방법으로 제조되어 진다. 이축연신시킨 Poly(tetrafluoroethylene) (PTFE) sheet는 매우 우수한 높은 투과성을 지니는 다공성 물질이 며, 본 연구에서는 이 막을 나일론 직물에 라미네이팅시킨 투습방수직물을 시료로 사용하여 라미네이팅 후의 역학특성 변화를 분석 하였다. 라미네이팅에 따른 투습방수직물의 물성과 역학특성의 변화에 관하여 살펴본 결과 다음과 같은 결과를 얻었다. 3-layer 라미네이팅 직물(base fabric-PTFE membrane-knitted lining)의 인열강도는 2-layer라미네이팅 직물 (base fabric-PTFE membrane)에 비해 매우 높게 나타났으며, 가공 전 직물과 비교하여 코팅직물에서 나타난 것과 같은 인열강도의 감소는 나타나지 않았다. 직물-PTFE 막 복합체 의 경우, 라미네 이 팅 이 파단강도 및 파단신도 의 증가에 기여 한 것으로 나타났으며 특히 3-layer 라미네이팅 직물의 경우, 신장률이 20%를 넘어서면서 강도가 현저히 증가하였다. 의복을 착용하였을 때 가해질 수 있을 정도의 소변형(small deformation) 하에서의 역학특성 에 있어서는 라미네이팅에 의해 전단특성이 가장 유의한 변화를 나타내었다. 전단강성(G)과 전단 히스테리시스 (2HG,2HG5)모두 증가하였고, primary hand value 중에서는 stiffness 가장 현저한 증가를 나타내었다

• Food Science of Animal Resources
• /
• v.24 no.1
• /
• pp.73-79
• /
• 2004

Functional properties of farm-grown pheasant meat with different sex, age and cutting portion were investigated, and the textural and sensory characteristics of processed products were also evaluated. Chemical composition of pheasant meat was characterized to be high in protein and low in fat, and breast muscle showed more protein and less moisture than thigh muscle. Moisture/protein ratio of the pheasant meat was relatively low in a range of 2.82∼3.40, indicating the pheasant meat would be a good source of processed meat, and it had high water holding capacity and myofibrillar protein extractability with some variations depending on age and portion cut(p<0.05). Thigh muscle showed higher value of L＊ and b＊ and lower value of a＊ than breast muscle. However, no difference was observed in color of meat with different age and sex. The meat from the 6 months and the breast cut had lower shear force than those of respective 17 months and the thigh regardless of sex. The pressed ham and sausage manufactured with the pheasant meat had better score than the commercial products manufactured with pork or chicken in sensory and textural parameters.

• Elastomers and Composites
• /
• v.40 no.2
• /
• pp.104-111
• /
• 2005

Virgin fluororubber(FKM) that is one of the highly-functionalized and expensive special rubber, and recycled FKM that is crushed by high temperature shear-crushing technique from recycled FKM were blended with the various mixing ratio to rubber blends. The cure characteristics and physical properties of these blended rubber compounds were investigated with various contents of recycled FKM and physical properties fur heat and fuels were also measured. Recycled FKM which is prepared by high temperature shear-crushing technique were blended to virgin FKM with the range of $0{\sim}50$ phr. The physical properties indicated that the rubber blend of recycled FKM with 30 phr turned out to be the best compound showing good dispersibility, heat resistance and fuel resistance and inexpensive in price.

• Geotechnical Engineering
• /
• v.9 no.3
• /
• pp.5-22
• /
• 1993

A series of laboratory tests (physical and mechanical index and engineering design) were conducted on undisturbed granite soils of CW and RS weathering grades in Korea. From these testes it can be concluded that most of physical and mechanical index values are very sensitive to change in weathering grade from CW to RS. Engineering design tests indicate that the unconfined compressive strength and the shear strength parameters are significantly reduced and that the soil becomes ductile and plastic with increasing weathering and saturation. It was found that weathered granite soils have the special characteristics when water saturated: (i) they significantly lose their shear strength(especially cohesion) and unconfined compressive strength, (ii) they are fragile and their grains break down in water as observed in grain size analysis.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.5
• /
• pp.109-122
• /
• 2002

The water content of soil near the ground subgrade varies seasonally, and dynamic deformational characteristics of soil are affected by the variation of water content. Contrary to previous studies which used various specimens of different compaction moisture contents, the influences of water content and capillary Pressure on dynamic deformational characteristics of soil were investigated using the given specimen controlling the matric suction. RC/TS(resonant column and torsional shear) testing equipment was modified so that it can control water content with changing capillary pressure(matric suction). RC/TS tests were performed on subgrade soil collected in the KHC(Korea Highway Corporation) test road. In the field, the cross-hole tests were performed and the water contents were measured at the same site to verify the feasibility and applicability of RC/TS test results. As water content decreased, the tendency of increasing shear moduli in field was well matched with laboratory test results.

• The Journal of Engineering Geology
• /
• v.22 no.3
• /
• pp.293-307
• /
• 2012

Shear wave velocity is commonly invoked in explaining geophysical phenomena and in solving geotechnical engineering problems. In particular, the importance of shear wave velocity in geotechnical earthquake engineering has been widely recognized for seismic design and seismic performance evaluation. In the present study, various insitu seismic tests were performed to evaluate geotechnical dynamic characteristics at 183 sites in Korea, and shear wave velocity profiles with depth were determined to be representative of the dynamic properties at the investigated sites. Subsurface soil and rock layers at the target sites were reclassified into five geotechnical layers: fill, alluvial soil, weathered soil, weathered rock, and bedrock, taking into account their general uses in geotechnical earthquake engineering practice. Average shear wave velocity profiles for the five geotechnical layers were obtained by synthesizing the shear wave velocity profiles from seismic tests in the field. Based on the profiles, a representative shear wave velocity value was determined for each layer, for use in engineering seismology and geotechnical earthquake engineering.