• Korean journal of applied entomology
• /
• v.31 no.2
• /
• pp.182-189
• /
• 1992

The influnces of 9 kinds of solvents on the toxicities against several insect species, phytotoxicity and solubility of compounds were evaluated by means of leaf dipping and spray methods. In case of the spray application, density and vapor pressure seemed to be a contributing factor to lethal toxicity against brown planthopper and diamond-back moth, respectively; the bigger the property of density and the smaller the vapor pressure gave the stronger toxicity. It appeared that the toxicity of solvents was not correlated with anyone of physical properties such as boiling point, dipole moment, dielectric constant, surface tension and viscosity. Spray treatment gave more toxicity to insects than leaf dipping treatment. Although dielectric constant and dipole moment seemed to be contributing factors to phytotoxic damage to rice seedling and bean plants, respectively, no general correlation between phytoxicity and the other physical properties was found. Leaf dipping application caused stronger phytotoxicity than spray application. It is concluded that 5% acetone solution may be most suitable to test chemicals because of its favorable solubility of compounds, lower toxicity to insects, and lower phytotoxicity.

• Food Science and Preservation
• /
• v.23 no.3
• /
• pp.355-360
• /
• 2016

In this study, the quality characteristics of spray dried powders from unripe fig extract were investigated. The protease activities of unripe fig and peeled unripe fig extract were 0.11 unit/mL and 0.28 unit/mL, respectively. The spray dried powder of unripe fig extracts was analzed using different maltodextrin ratios (F-MD 5, 5% maltodextrin; F-MD 10, 10% maltodextrin; and F-MD 20, 20% maltodextrin). The spray-dried powder showed the highest protease activity with F-MD 10 (0.84 unit/g). The moisture content and L value of the spray-dried powder were higher than those of the freeze-dried powder. The particle diameter of the freeze-dried powder ($209.67{\mu}m$) was higher than that of the spray-dried powders ($22.18{\sim}37.33{\mu}m$). The water absorption index ranged from 0.18 to 0.40, while the water solubility index ranged from 94.40% to 98.80%. In the in vitro digestion study, spray-dried powders of the unripe fig showed a protease survival range of 16.47%~24.80%. In conclusion, it is considered appropriate to use the spray-dried powder (F-MD 10) of unripe fig as a meat tenderizer for processing food.

• Resources Recycling
• /
• v.17 no.6
• /
• pp.79-88
• /
• 2008

This study is the previous stage for the mass production technology development of the nano-sized tin oxide powder by the recycling of the wasted tin metal, and nano-sized tin oxide powder with the average particle size below 50 nm is prepared from the tin chloride solution by the spray pyrolysis process. As the reaction temperature increases from 800 to 850, the average particle size of the generated powder increases from 20 to 30 nm. As the reaction temperature increases to 900, the droplet type is composed of the particles with the average size of the 30 nm. while the average size of the independent particles increases up to $80{\sim}100$ nm and the surface microstructure becomes more solid. Until $900^{\circ}C$, as the reaction temperature increases, the XRD peak intensity increases, while the specific surface area decreases. When the reaction temperature increases to 950, most of the powder appears with the independent type and the average particle size decrease down to 70 nm. The XRD peak intensity greatly decreases and the specific surface area increases almost twice.

• Resources Recycling
• /
• v.27 no.2
• /
• pp.24-31
• /
• 2018

In this study, waste ITO target is dissolved into hydrochloric acid to generate a complex indium-tin chloride solution. Nano sized ITO powder with an average particle size below 30 nm are generated from these raw material solutions by spray pyrolysis process. Also, in this study, thermodynamic equations for the formation of indium-tin oxide (ITO) are established. As the reaction temperature increased from $800^{\circ}C$ to $900^{\circ}C$, the proportion and size of the spherical droplet shape in which nano sized particles aggregated gradually decreased, and the surface structure gradually became densified. When the reaction temperature was $800^{\circ}C$, the average particle size of the generated powder was about 20 nm, and no significant sintering was observed. At a reaction temperature of $900^{\circ}C$, the split of the droplet was more severe than at $800^{\circ}C$, and the rate of maintenance of the initial atomized droplet shape decreased sharply. The average particle size of the powder formed was about 25 nm. The ITO particles were composed of single solid crystals, regardless of reaction temperature. XRD analysis showed that only the ITO phase was formed. Remarkably, the specific surface area decreased by about 30% as the reaction temperature increased from $800^{\circ}C$ to $900^{\circ}C$.

• Journal of ILASS-Korea
• /
• v.20 no.2
• /
• pp.95-100
• /
• 2015

Lower recirculated gas temperature at EGR system reduces NOx and PM emissions. However, EGR Cooler can be polluted by PM generated from recirculated EGR gas, and it reduces cooling efficiency and the amount of EGR gas simultaneously. The SECFR(Steam EGR Cooler Fouling Remover) system which uses the evaporated washer fluid steam caused by high temperature of EGR gas was manufactured for removing fouling generated on the cooler surface. Since an injection pressure of wind shield washer fluid in the vehicle is approximately 0.5 bar, it is not enough to atomize the injected washer fluid. Thus, it is necessary to apply a method to atomize the washer fluid. In this study, the impinging plate was used to promote the atomization of spray washer fluid for the purpose of apply SECFR system to vehicles and measured the DAR(Droplet Area Ratio) and DUI(Droplet Uniformity Index) through the spray visualization.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.353-355
• /
• 2008

최근 석탄 가스화 기술은 화석연료인 석탄을 기존의 공해물질 발생을 90%이상 줄이면서 고효율로 활용할 수 있는 방법으로 각광받고 있다. 본 연구는 습식 석탄 가스화기에서 가스화의 핵심적인 요소인 버너의 분무 관계 분야에 대한 분무 특성 및 무화성능을 높일 수 있는 분무기의 구조 및 운전 조건 등을 제시 할 목적으로 분무 시 내부를 관찰 할 수 있는 아크릴을 이용하여 내부 혼합식 버너를 제작하였다. 미립화 특성을 파악하기 위하여 $O_2$/Fuel Ratio 및 버너의 내부 혼합 방식, 분사각도, 각 분사 높이에 따른 미립화 특성을 관찰하였으며, 입도 분석은 심파텍사의 입도 분석기를 이용하여 측정하였다. 내부 혼합식 버너의 입도는 분사 각도와 $O_2$/Fuel Ratio에 따라서 변화하는 경향을 나타냈으며, 공급되어지는 Fuel은 석탄 슬러리와 물을 이용하여 각각의 입도를 측정하였다. slurry의 공급량이 고정된 상태에서 산소 공급량이 증가함에 따라 미립화도는 증가하는 경향을 나타내었으며, 슬러리 공급량과 산소 공급량이 동일한 경우 버너의 분사 각도에 따라 미립화도가 다르게 나타나는 특성을 관찰하였다.

• Journal of the Korean Ceramic Society
• /
• v.41 no.3
• /
• pp.242-246
• /
• 2004

Nano-sized a-alumina with a narrow distribution was prepared by using Flame Spray Pyrolysis (FSP). The microemulsion of water in oil (W/O) was prepared to make ultrafine droplets for FSP process. Kerosene (fuel) as a continuos phase and Al(NO$_3$)$_3$$.$9$H_2O$ (oxidizer) aqueous solution as a dispersed phase were prepared for microemulsification. The microemulsion with dispersion stability was obtained by adjusting the composition of 80 vol% kerosene, 10 vol% aqueous solution, and 10 vol% emulsifying agent. Microemulsion was sprayed onto the flame by using two-fluid nozzle spray gun under the condition of 0.03 ㎫ air pressure. The synthesized products were $\alpha$-alumina phase with the size of 20 to 30 nm.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.4 no.3 s.14
• /
• pp.83-87
• /
• 2004

In underground culvert are established main and basic facilities for electric power, communication, gas and heating pipe etc. In the future the use of underground culvert will be enlarged and the peril of fire will be increased. Thus it is necessary to make a general plan to prevent fire. The skills to prevent fire in underground culvert will be accumulated by the spray distribution of the nozzle and domestic skills in fire fighting will be upgraded. It will also contribute to the construction of common small fire fighting system suitable to the domestic surrounding and the growth of domestic skills for fire fighting and disaster prevention.

• KSBB Journal
• /
• v.22 no.3
• /
• pp.151-156
• /
• 2007

Increasing public concerns over odors and air regulations necessitates the remediation of a wide range of odorous compounds for industrial purpose. Currently, wet scrubbing technique by neutralization using essential oils is utilized to treat methyl mercaptan odor. The chemical analysis is performed to analyze the composition of an essential oil by GC-MS. The objective of this study is to clarify the possibility of the neutralization of odors sprayed in the fixed bed and determine the removal efficiencies in the misty aerosol by different input odor concentration. It is found that methyl mercaptan is significantly removed in the wet scrubber, and their removal efficiency of methyl mercaptan is obtained by 98%.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.33-33
• /
• 2003