• Progress in Medical Physics
• /
• v.6 no.2
• /
• pp.51-60
• /
• 1995

Lithium Fluoride (LiF; TLD-100) crystal chips are normally used as thermolu minescence dosimeters (abbreviated as NC-100) for estimating the absorbed dose to the skin of a patient or in a solid water phantom undergoing radiotherapy with megavoltage photon (6 and 15MV) beams. In general, investigation has revealed a reduction in the sensitivity of NC-100 chips after many runs through heating cycles. A TLD-100 chip laminated with gold plate (140${\mu}{\textrm}{m}$) on the upper surface layer of its face toward the photon beam (abbreviated as GC-100) has properties different from that of a NC-100 chip activated by incident photons and contaminant electrons with various lower energies coming from the gantry head and air. Activation of the valence band electrons of GC-100 chips by incident photons, positrons and electrons-which come from the gold plate by mainly pair production process and partly from Compton scattering-results in more enhanced signal intensity, higher response per monitor unit, as well as a good linearity with monitor units and independence of dose rate. Since the electron beams (6 and 15 MeV) do not have the probability of pair production process with gold plate, there is only a small difference (about a 3.3％ increase for 15 MeV) in the signal gaps in the TL readout for electron beams between GC- and NC-100 chips. The 3.3％ increase is entirely due to the buildup caused by the 140 m gold plate. The sensitivity of GC-100 chips is much more susceptible to high energy photon beams than electron one because of pair production. The interaction of high energy photon with a material of high atomic number, such as the good plate in this case, results in a considerably significant probability of pair production. The gold plate on the NC-100 chips acts as not only an intensifier of their signals but also acts as a filter of contaminant electrons in therapeutic high energy X-ray beams.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.6
• /
• pp.673-680
• /
• 2017

Research and commercialization of wood chips-urethane resin mixtures as paving materials for park trails and tourist attractions are underway. The aim of this study was to expand the use of such paving materials to the playgrounds, where vigorous physical movements occur frequently. For this purpose, the physical properties and safety of the paving material, in which some or all of the wood chips(passing through a 10mm sieve and remaining in a 3mm sieve) were replaced with sawdust, were studied experimentally. Strength, elastic modulus, slip resistance, shock absorption and heavy metal content tests were carried out by varying the mixing ratio of urethane resin, sawdust and wood chip. As a result, in the case of wood chip-resin mixtures with mass ratios of the resin to total mass of sawdust and wood chips of 1.0 and 1.2 and having a ratio of sawdust mass to total mass of sawdust and wood chips of 0-0.4, it was found that the properties satisfied KS F 3888-2. On the other hand, in case of using sawdust only as a woody material, the shock absorbability was below standard, and the mass ratio of resin to sawdust required 1.2 or more to ensure the specified tensile strength.

• Asian Journal of Turfgrass Science
• /
• v.15 no.3
• /
• pp.119-126
• /
• 2001

The susceptibility of Ectinohoplia rufipes, insect pest of landscaping trees in golf courses to registered insecticides in golf courses was investigated. In addition, effect of host plants, Ainus firma, Prunus serrulata var. spontanae, and Osmantus asiaticus on susceptibility of E. rufipes were tested in laboratory with efficacy of some insecticides in laboratory and fields. The insecticides used in experiments were cabaryl 40%+phosalone 20% WP, chlorpyrifos-methyl 25% EC, chlorpyrifos 20% + diflubenzuron 7% n, deltamethrin 1% EC, ethopenprox 8% +diazinon 25% WP, and fenitrothion 50% EC. Mortalities of E.rufipes were 100% except chlorpyrifos-methyl. when A. firma leaves dipped in recommended concentration of given insecticides were supplied as food to adult of E. rufipes. LC$_{50}$s of insecticides were different depending on host plants, that is, those of deltamethrin were 0.21 ppm in Ο. asiaticus, 0.45 ppm in P. serrulata var. spontanae, and 0.77 ppm in A. firma. LC$_{50}$s of fenitrothion were 24.1 ppm, 64.0 ppm, and 11.0 ppm and those of chlorpyrifos-methyl were 97.2 ppm, 40.6 ppm, and 29.6 ppm, respectively. LC$_{50}$ was the lowest in Ο. asiaticus and that of chlorpyrifos-methyl and fenitrothion was the lowest in A. firma. Deltamethrin was the most effective against adult of E. rufipes in field like in laboratory and persisted in two weeks.weeks.

• The korean journal of orthodontics
• /
• v.19 no.2
• /
• pp.7-24
• /
• 1989

The physical properties of seven sizes of control groups and experimental group in stainless steel orthodontic wires were studied in tension, hardness, bending, torsion and observation of microstructure. The wires (0.40-0.90mm dia.) of round type were tested in the as-received condition. The wires of control groups were TRU-CHROME and REMANIUM, and experimental group was SK wire which was developed by ourselves and made in Korea. The results were as follows; 1. The chemical compositions of control groups and experimental group were austenite stainless steel wires of SOS 304. 2. Higher values of tensile and yield strength in tension were control group I, experimental group, control group II. Maximum tensile and yield strength of experimental group were $203.63{\pm}1.41kg/mm^2$ in 0.70mm diameter and $148.96{\pm}4.88kg/mm^2$ in 0.60mm diameter, and maximum elongation was $5.20{\pm}0.57%$ in 0.45mm diameter. 3. Hardness values of experimental group were similar to control groups. Maximum hardness values were $596.2{\pm}13.66Hv$ in 0.45mm diameter wire of control group I, $590.5{\pm}20.08Hv$ in 0.50mm diameter wire of control group II, and $563.6{\pm}5.35Hv$ in 0.70mm diameter wire of experimental group. 4. Torsion properties of experimental group were similar to control group I and more than control group II. Maximum torsion cycles were $31.8{\pm}2.48$ in 0.45mm diameter of control group I, $17.4{\pm}4.84$ in 0.60mm diameter of control group II, and $24.6{\pm}3.04$ in 0.45mm diameter of experimental group. 5. Maximum bending cycles of experimental group were smaller than control groups. Maximum bending cycles were $9.00{\pm}0.00$ in 0.50mm diameter wire of control group I, $10.0{\pm}0.82$ in 0.40mm diameter wire of control group II, and $8.0{\pm}1.26$ in 0.50mm diameter wire of experimental group. 6. Microstructures of experimental and control groups co-existed with martensited austenite structure and elongated austenite structure. 7. The direction of wire fracture was propagated parallel to torsion direction typically and there was no probability showing wire fracture at inclusions and surface scratches. 8. The type of wire fracture was brittle fracture at initiation site and ductile fracture at core.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.19 no.4
• /
• pp.269-279
• /
• 2003

This study investigated the mechanical properties of precious metal-ceramic alloy joined by the laser-welding and the soldering compared with the parent metal. Twenty-four tensile specimens were cast in precious metal-ceramic alloy and divided into three groups of eight. All specimens in the control group(group 1) were left in the as-cast condition. Group 2 and 3 were the test specimens, which were sectioned at the center. Eight of sectioned specimens were joined by soldering with a propane-oxygen torch, and the remaining specimens were joined by laser-welding. After joining, each joint diameter was measured, and then tested to tensile failure on an Instron machine. Failure loads were recorded, and then fracture stress(ultimate tensile strength), 0.2% yield strength and % elongation calculated. These data for three groups were subjected to a one-way analysis of variance(ANOVA). Neuman-Keuls post hoc test was then used to determine any significant differences between groups. The fracture locations, fracture surfaces were examined by SEM(scanning electron microscope). The results were as follows: 1) The tensile strength and 0.2% yield strength of the soldered group($280.28{\pm}49.35MPa$, $160.24{\pm}26.67MPa$) were significantly less than both the as-cast group($410.99{\pm}13.07MPa$, $217.82{\pm}17.99MPa$) and the laser-welded group($383.56{\pm}59.08MPa$, $217.18{\pm}12.96MPa$). 2) The tensile strength and 0.2% yield strength of the laser-welded group were about each 98%, 99.7% of the as-cast group. There were no statistically significant differences in these two groups(p<0.05). 3) The percentage elongations of the soldered group($3.94{\pm}2.32%$) and the laser-welded group($5.06{\pm}1.08%$) were significantly less than the as-cast group($14.25{\pm}4.05%$) (p<0.05). 4) The fracture of the soldered specimens occurred in the solder material and many porosities were showed at the fracture site. 5) The fracture of the laser-welded specimens occurred also in the welding area, and lack of fusion and a large void was observed at the center of the fracture surface. However, the laser-welded specimens showed a ductile failure mode like the as- cast specimens. The results of this study indicated that the tensile strengths of the laser-welded joints were comparable to those of the as-cast joints and superior to those of the soldered joints.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.10 no.2
• /
• pp.129-138
• /
• 2005

Sediment texture, physical (porosity, water content, bulk density, grain density, and shear strength), and geoacoustic properties (compressional wave velocity and attenuation) were measured on eighteen core samples collected from the shelf off eastern Geoje Island, the South Sea of Korea. Based on these properties, the study area is divided into three different sub-areas: (1) Area I affected directly by the Nakdong River discharge; (2) Area II covered by the southern branch of the Nakdong River discharge; and (3) Area III dominated by relict sediment. Mean grain size, velocity, and bulk density decrease from Area $I(7.4\Phi,\;1528m/s,\;1.6g/cm^3,\;respectively)$ to Area $II(8.1\Phi,\;1485m/s,\;and\;1.5g/cm^3)$, and then increase rather rapidly in Area $III(1.4\Phi,\;1664m/s,\;and\;2.2g/cm^3)$. Porosity, on the other hand, exhibits an opposite trend, increasing from Area $I(64.5\%)$ to Area$II(73.9\%)$ and then decreasing significantly in Area $III(32.9\%)$ From the results measured and calculated, we suggest a specified geoacoustic model in the study area.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.40 no.3
• /
• pp.159-167
• /
• 2013

The aim of this study was to evaluate changes in demineralization resistance and bonding strength of light cured glass ionomer after the addition of nano hydroxyapatite in various ratios. Fuji II LC GIC (GC Co., Japan) was used as the control group and also as a base material for experimental group. HA was mixed into the RMGIC at various ratio to create a HA-LC GIC mixture, preparing six experimental groups, i.e. 5%, 10%, 15%, 20%, 25%, 30% HA-LC GIC. According to the results, the bonding strength increased due to the addition of HA, showing the maximum value at the 15% nano HA group (p < 0.05). Under CLSM observation after 4 days of demineralization, the HA groups were more resistant to demineralization compared to the control group. No significant difference was observed between HA groups. In analysis through SEM, the HA groups showed attachment of granular materials and decreased demineralized tooth surfaces under influence of HA particles.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.25 no.4
• /
• pp.437-444
• /
• 2009

The purpose of this study was to evaluate the physical properties of different automixing resin cements and the shear bond strength on dentin. For this study, two self-adhesive automixing resin cement(Rely-X Unicem(3M ESPE, St. Paul, USA), Embrace resin cement(Pulpdent, Oakland, USA)) and one chemical polymerizing resin cement(Resiment Ready-Mix(J.L.Blosser Inc., Liberty Missouri, USA)) were used. To evaluate the physical properties, compressive strength, diametral tensile strength and flexural strength were measured. The specimens were fabricated using Teflon mould according to manufacturers' instructions and stored for 24 hours in an atmosphere of 100% humidity. To evaluate the shear bond strength on dentin, each cements were adhered to buccal dentinal surface of extracted human lower molars in 2mm diameter. Physical properties and shear bond strengths were measured using universal testing machine(Z010, Zwick GmbH, Ulm, Germany) at a crosshead speed of 0.5mm/min. The physical properties and shear bond strength of different automixing resin cements were statistically analyzed and compared between groups using One-way ANOVA test and Schffe post-hoc test at the 95% level of confidence. The result shows that chemical polymerizing automixing resin cement represents the relatively higher physical properties and shear bond strength than self-adhesive automixing resin cements.

• Restorative Dentistry and Endodontics
• /
• v.27 no.1
• /
• pp.77-86
• /
• 2002

Current composites are made with dimethacrylate monomers and silane-treated silica microfillers, either alone or with silane treated glass fillers The main reasons for clinical failure of dental composites are secondary caries, wear and fracture. Most of practitioner want to get a composite which is more tougher under occlusal stress, less polymerization contraction, and better handling properties in application clinically. The aim of this study was to investigate the influence of resin matrix with various flows on the physical proper-ties such as fracture toughness and degree of conversion of the experimental resins. It was hypothesized that flexible or tough resin composites can be designed by judicious choice of monomer composition Various flow resin matrices containing Bis-GMA, UDMA, and TEG-DMA were made by altering the pro-portion of the monomers. After the unfilled resins were light-cured for different light intensity, the fracture toughness(K$_{1c}$) was measured according to ASTM standard using the single edge notched geometry, and degree of conversion(DC) was measured by FTIR. And experimental composites were formulated with variations in the proportion of silanated quartz and strontium glass fillers as 60, 75, and 77wt%. Also, the physical properties of composites with various filer contents were evaluated as same manner. All resulting data were compared by ANOVA/Tukeys test at 0.05 level. The results were as follows; 1. The degree of conversion of high flow resin containing less Bis-GMA was higher than that of low flow unfilled resin 2. While the degree of conversion of unfilled resin was increased according to light intensity for polymerization, there was no significant increase with moderate and high light intensity. Also, the fracture toughness was not increased by high light intensity. 3. The fracture toughness was high in the low flow unfilled resin containing higher contents of Bis-GMA. 4. There was a significant increase for fracture toughness and a tendency for degree of conversion to be reduced when the content of fillers was increased. 5. In the experimental composites, the flow of resin matrix did not affected on the fracture toughness, even, which was decreased as increase of viscosity. These results showed that the physical properties of a dental composite could be attributed to the flow of resin matrix with relative content of monomers. Specific combination of resin monomers should be designed to fulfil the needs of specific indication for use.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.41 no.3
• /
• pp.308-317
• /
• 1996

These experiments were conducted to investigate variation of physical characteristics of the culm related to lodging resistance by nitrogen levels under direct seeding on flooded paddy surface. The number of seedling per m$^2$ were from 103 to 110 plants, and seedling ratios were ranged from 66.7% to 71.2%. The lodging occurrence were increased in order to the nitrogen levels 15 kg, 10 kg, 5 kg /10a, and the lodging resistant varieties ; Dongjinbyeo and Cheongmyungbyeo showed less values of field lodging than those of lodging susceptible varieties ; Daecheongbyeo, Palgongbyeo and H waseongbyeo. The lodging resistance was decreased in semidwarf varieties compare with long culm varieties, but Dongjinbyeo, long culm variety has lodging resistance. The occurrence of lodging decreased with lower values in top moment, but with higher values in the breaking moment with leaf sheath. The root dry weight positively correlated with weight of culm base, but modulus of section was negatively correlated with bending curvature, respectively.