• Title/Summary/Keyword: 문집

Search Result 448,643, Processing Time 0.326 seconds

Cyclic Behavior of Wall-Slab Joints with Lap Splices of Coldly Straightened Re-bars and with Mechanical Splices (굽힌 후 편 철근의 겹침 이음 및 기계적 이음을 갖는 벽-슬래브 접합부의 반복하중에 대한 거동)

  • Chun, Sung-Chul;Lee, Jin-Gon;Ha, Tae-Hun
    • Journal of the Korea Concrete Institute
    • /
    • v.24 no.3
    • /
    • pp.275-283
    • /
    • 2012
  • Steel Plate for Rebar Connection was recently developed to splice rebars in delayed slab-wall joints in high-rise building, slurry wall-slab joints, temporary openings, etc. It consists of several couplers and a thin steel plate with shear key. Cyclic loading tests on slab-wall joints were conducted to verify structural behavior of the joints having Steel Plate for Rebar Connection. For comparison, joints with Rebend Connection and without splices were also tested. The joints with Steel Plate for Rebar Connection showed typical flexural behavior in the sequence of tension re-bar yielding, sufficient flexural deformation, crushing of compression concrete, and compression rebar buckling. However, the joints with Rebend Connection had more bond cracks in slabs faces and spalling in side cover-concrete, even though elastic behavior of the joints was similar to that of the joints with Steel Plate for Re-bar Connection. Consequently, the joints with Rebend Connection had less strengths and deformation capacities than the joints with Steel Plate for Re-bar Connection. In addition, stiffness of the joints with Rebend Connection degraded more rapidly than the other joints as cyclic loads were applied. This may be caused by low elastic modulus of re-straightened rebars and restraightening of kinked bar. For two types of diameters (13mm and 16mm) and two types of grades (SD300 and SD400) of rebars, the joints with Steel Plate for Rebar Connection had higher strength than nominal strength calculated from actual material properties. On the contrary, strengths of the joints with Rebend Connection decreased as bar diameter increased and as grade becames higher. Therefore, Rebend Connection should be used with caution in design and construction.

멕시코 로얄 은광산 잠재성 평가

  • Heo, Cheol-Ho;Kim, Ui-Jun
    • 한국지구과학회:학술대회논문집
    • /
    • 2010.04a
    • /
    • pp.108-109
    • /
    • 2010
  • IMPACT Silver 주식회사는 Zacualpan 프로젝트의 Royal Mines(이하 로얄 광산)을 인수했다. $124.5\;km^2$에 해당하는 지역의 소유권은 두 개의 멕시코 사기업으로부터 가행중인 광산의 채굴권 구입과 운영 중인 기반시설의 임대를 조건으로 한다. 프로젝트 지역은 멕시코시티로부터 남서방향으로 100 km와 Taxco Silver 광산으로부터 북서방향으로 25 km 떨어진 지점에 위치한다. 기반시설은 비포장 도로, 충분한 전력과 물의 공급 및 숙련공들을 갖추어 우수한 평가를 받고 있다. 소유권은 멕시코인의 개인소유 하에서 무한한 매장량 혹은 자원량을 갖고 운영된 채광과 가공시설을 인수하는 것이다. 소유권 지역을 대상으로 한 IMPACT Silver사의 주 탐사목적은 이미 알려진 광화대의 확장을 위한 잠재성 평가와 다른 지역에서 신규 광상의 유망지역을 발견하는 것이다. Zacualpan 프로젝트의 로얄 광산은 남동 Guerrero terrane의 북부에 위치한다. Teloloapan subterrane은 주로 저변성 녹색편암상으로 구성된 쥬라기 후기에서 백악기 초기의 화산성 퇴적층으로 구성된다. 대부분의 유망지역은 Lower Villa de Ayala층의 중성 내지 염기성 화산성 쇄설암을 모암으로 한다. 다상의 변성작용은 지역 전반에 걸쳐 나타나고, Zacualpan 광산지역에서 수반되는 광화작용을 규제한다. Zacualpan 광산지역은 Sierra Madre del Sur로 알려진 유망 광화대에 해당한다. 이 지역은 화산성 괴상 황화광상과 천열수 맥상광상이 우세하다. 대부분의 천열수 광화작용은 3.2-3.8억 년 전 마그마의 생성이 활발한 판구조 체제 동안 발생하였다. 역사적으로 가장 주요한 지역은 Lipton Vein이다. 현재 Zacualpan 지구에서 채광량은 은 200-500 g/t 정도로 보고되고 있다. 일부 지역은 고품위 은 광화작용(은 1,000 g/t 이상)을 수반하고 있으며, 이는 탐사의 주 타겟이 되고 있다. Zacualpan에서 은 광화작용은 은이 부화된 중유황 천열수 맥상광상으로 상당히 유명하다. Fresnillo, Pachuca 및 Taxco 광산을 포함한 멕시코 소유의 대규모의 잘 알려진 광산들이 이에 해당한다. 이러한 광산들은 부산물로서 금, 아연, 연이 생산된다. 이러한 광상들은 맥상과 각력상 및 산점상 또는 망상세맥의 형태로 산출된다. 광화작용은 석영과 탄산염 맥 내에 주로 황철석과 다양한 섬아연석, 방연석, 은 혹은 금 광물들을 수반한다. 경제성을 갖는 광화작용의 수직적인 연장은 평균적으로 대략 300 m이고, 멕시코 중부에 위치한 Fresnillo의 광화작용은 100 m에서 960 m의 연장을 갖는 것으로 알려져 있다. 아주 오랫동안 Zacualpan에서 광산관계자의 관측과 IMPACT Silver에서 최근 작업의 결과를 토대로, Zacualpan 광산지역의 탐사모델은 새로운 광상의 탐사를 위한 가이드로서 개발되었다. Zacualpan 광산지역에서 가장 높은 경제성을 갖는 광화작용은 북서와 남북방향의 맥 구조를 따라 수반된다. 이러한 맥 구조들은 종종 이 지역을 가로질러 수 km까지 추적되지만, 경제성을 갖는 광화작용은 맥 구조를 따라서 구조적으로 유리한 지역에서 부광대를 형성한다. 부광대를 형성하기 위한 가장 유리한 구조적 지역은 북서와 남북방향으로 발달한 맥 구조들이 교차하는 지역이다. 지난 30년간 채광된 주요 부광대는 폭이 2-6 m 이고 수평연장은 30-150 m 그리고 수직연장은 230-300 m에 이른다. 가장 높은 생산량을 보이는 부광대는 남북방향의 이차 맥들이 Guadalupe 광산의 Lipton 맥을 가로지르는 지역에서 발달한다. 남동쪽으로 현재 Compadres 광산의 Silver Shoot No. 1으로부터 고품위 은을 생산하는 지역은 북서방향의 San Agustin 맥이 북향의 Cometa Navideno 맥에 의해 절단되는 지역에서 산출한다. 모암은 광화작용을 규제하는 또 다른 중요한 요소이다. 광산지역에서 경제성을 갖는 모든 광화작용은 중성 내지 염기성 화산암 특히 안산암과 관련 모암에 배태된다. 부광대가 셰일 혹은 편암으로 전이되는 지역에서, 맥들은 소규모의 세맥으로 나뉘어 진다. Zacualpan의 전형적인 천열수 광상에서 부광대는 상부로 가면서 은의 함량이 증가하고, 하부로 가면서 연 아연의 함량이 증가하는 수직적 대상을 보인다. 금의 함량 변화는 보다 예측이 어려우나 상당히 중요하다. Zacualpan 광산지역의 탐사모델에 사용된 토양 채취, 정밀지도제작, 트렌치 및 시추탐광은 현재 IMPACT Silver사가 이 지역을 대상으로 한 가장 효율적인 탐사방법으로 입증되었다. Zacualpan 프로젝트의 로얄 광산은 하루 500 톤을 제련하는 기반시설과 수반된 채굴권을 갖는 가행 광산들을 포함한다. 현재 IMPACT Silver사는 두 곳의 타겟 지역에서 정밀지도제작, 토양 및 암석 채취, 12공 총 1866 m의 시추탐광에 의한 사전조사로 구성된 4 단계 탐사를 수행했다. 암석 1,953개, 토양 1,631 개, 389 개의 시추코어 시료가 채집되고 분석되었다. 이러한 작업은 추가탐사를 요구하는 수많은 유망 광화대를 규명했다. Compadres 광산에서 현재 가행중인 지하갱 시료는 레벨 1에서 0.9 m의 폭을 갖는 광체에서 은 680 g/t과 금 0.3 g/t, 레벨 3에서 1.67 m의 폭을 갖는 광체에서 은 12,591 g/t과 금 12.07 g/t의 품위를 갖는 것으로 나타났다. 레벨 1에서 3까지 2-3 m의 폭과 30-40 m 연장으로 채광되었다. 시추탐광은 고품위를 갖는 몇몇의 중첩된 맥을 발견했다. Compadres 광산에서 남동방향으로 200 m지점에 위치한 Soledad 지역에서 5 개의 시추공으로부터 동일 맥 시스템이 발견되었고, 고품위 부광대의 상부로 간주되는 몇몇 중요 지점이 발견되었다. 초기 단계의 탐사는 유망 시추탐광 지역인 중간정도 내지 고품위 유망 광화대를 규명했다.

  • PDF

위성자료를 이용한 토지피복에 따른 열환경 평가

  • Jo, Su-Jin;Kim, Hae-Dong;An, Ji-Suk
    • 한국지구과학회:학술대회논문집
    • /
    • 2010.04a
    • /
    • pp.88-89
    • /
    • 2010
  • 최근 인간의 활동범위와 영역이 확대되고 산업이 발전하면서 인간의 삶과 지속가능한 발전 등 도시 기후에 관한 관심도 높아지고 있다. 산업혁명 이후 도시화와 산업화로 인해 인구가 증가하고 도시지역으로 집중됨으로써 도시 열섬화 현상에 대한 도시환경문제가 부각되고 있다. 이는 최근까지도 도시개발에 있어서 기능과 효율성이 우선시 되어 도시기후에 대한 배려가 이루어지지 못하고 있으며, 오히려 과도한 냉난방을 가동하는 등 쾌적한 실내 환경 조성을 위한 노력만을 행해왔다. 도시화에 따른 도시의 열환경 구조의 변화는 토지이용의 변화에 따른 피복상태와 밀접한 관련이 있다는 연구들이 수행된 바 있다. 이렇듯 도시화가 진행됨에 따라서 도심 지표면을 덮고 있는 포장재도 변하고 있다. 대표적인 토지피복재로는 콘크리트와 아스팔트 등의 인공포장재, 수계, 삼림 등으로 크게 나누어 볼 수 있다. 최근 도심의 발달로 인해 도심의 표면은 점차 인공포장재인 아스팔트와 콘크리트로 덮여지고 있다. 인공포장재는 맑은 여름철 낮에 받아들인 열을 야간에도 머금고 있어 도시열섬현상의 주요원인이 된다. 도시화가 진행됨에 따라 토지이용형태가 변화하고 있으며 이러한 토지피복의 변화는 그 지역의 기온과 풍향, 풍속뿐만 아니라 지표온도도 변화시키므로 도시 열환경 구조에 적지 않은 영향을 미치고 있다. 과거에는 자연 환경과 도시공간에 대한 인식이 다른 분야로 나누어져서 다루었지만 현재 위성영상 기술의 발달로 많은 공간 정보를 파악할 수 있게 된 바 도시기후변화에 더욱 직접적이고 근본적인 접근이 쉬워졌다. 원격탐사기법의 활용은 위성자료를 이용하여 동시간대 평면적인 열구조를 정량적으로 파악하는데에 중요한 자료를 제공하여 도시지역을 덮고 있는 인공자재의 존재가 도시열섬의 형성과 밀접하게 연관이 있다는 사실을 짐작할 수 있다. 따라서 도시기후변화의 문제점을 더욱 적극적으로 해결하기 위해서는 토지이용에 따른 지표면 온도 상승의 현황을 파악하고 이를 저감 시킬 수 있는 대책들이 수립되어야 한다. 본 연구는 보다 세분화된 도시 열환경을 정량적으로 분석 평가하기 위해서 토지피복별 분류를 3가지로 대구시 중구 경북대학교 부속 고등학교(이하 사대부고 지점)를 도심지역으로, 경상남도 창녕군 창녕읍 우포늪(이하 우포지점)을 수계지점으로, 경상북도 안동시 길안면 만음리(이하 안동지점) 지점과 대구시 칠곡군 동명면 득명리 팔공산 한티재 도립공원(이하 팔공지점)을 산림으로 분류하여 연구하였다. 대구 계명대학교 기후환경연구실에서 보유하고 있는 AWS(Automatic Weather Station) 자료로 기상요소를 분석하였으며, MODIS Terra 위성영상을 이용하여 지표온도를 추출하고 분석하였다. 또 기상요소와 지표온도를 이용해 회귀식을 도출하여 추정기온을 산출하였다. 그 결과 첫째, 계절에 따른 기온의 시간변화는 여름의 평균기온이 $25.13^{\circ}C$$24.12^{\circ}C$로 사대지점과 우포지점의 평균기온이 가장 높게 나타났으며, 이는 도심에서 발생되는 인공열의 영향으로, 우포지점은 수계의 특징이 반영된 결과라 할 수 있다. 둘째, 계절에 따른 풍속의 시간변화는 여름의 경우 우포지점의 풍속이 1.63m/s로 가장 높은 반면 안동지점의 풍속이 0.27m/s로 가장 낮은 것으로 나타났다. 겨울의 경우 팔공지점의 풍속이 1.82m/s로 가장 높게 나타났다. 토지피복에 따른 지표면의 변화가 도시기후에 미치는 영향을 정량적으로 평가하고, 또 지표면 온도와 기온과의 차이를 알아보기 위하여 MODIS 위성 영상을 이용하여 세 지점을 대상으로 토지피복에 따른 열환경을 평가 분석하여 다음과 같은 결론을 얻을 수 있었다. 첫째, MODIS 위성영상을 이용하여 산출한 지표면 온도는 여름철 주간에 안동지점의 경우 주변지역에 비해 지표면 온도가 약 $26^{\circ}C$로 낮게 나타났으며 우포지점의 경우 수계가 가지는 열 완충능력으로 약 $27^{\circ}C$의 낮은 지표면 온도를 나타내었다. 사대지점의 경우 약 $34^{\circ}C$이상의 높은 지표면 온도를 나타내었다. 둘째, MODIS 위성영상을 이용하여 산출한 지표면 온도와 관측된 기온과의 회귀식을 도출하여 상관분석 한 결과, 모든 지점의 값에서 상관성 및 신뢰도가 높은 것으로 나타났다. 셋째, 상관분석의 결과를 통하여 추정한 기온은 지표면 온도와의 차이가 있지만 유사한 패턴의 결과로 추출되었다. 이러한 결과로 볼 때 도시의 인공자재를 이용한 건축과 개발이 도시열섬현상을 유발하는데 중요한 역할을 하는 것을 정량적으로 평가할 수 있었다. 따라서 본 논문의 연구결과를 바탕으로 도시계획에 있어서 인공구조물에 의한 기온과 풍속이 받는 영향을 고려하여 도심의 인공구조물의 배치나 자재에 대한 개발이 이루어져야 할 것이며 열교환의 방해 및 바람순환이 확보되는 구조로 개선되어야 할 것이다.

  • PDF

대구지역 대기환경용량평가에 관한 연구

  • Choe, Geun-Sik;Kim, Hae-Dong
    • 한국지구과학회:학술대회논문집
    • /
    • 2010.04a
    • /
    • pp.90-91
    • /
    • 2010
  • 우리나라는 산업화와 도시화의 급속한 발전으로 인한 대기오염물질배출시설, 자동차 통행량, 에너지 사용량의 증가 등으로 대기오염물질배출원의 수와 규모가 증대되어 광역도시를 중심으로 대기질이 악화되고 있다. 특히 우리나라의 수도권대기질은 선진국의 주요 도시에 비해 대기오염 상태가 좋지 않은 것으로 평가됨에 따라 정부는 대기질을 OECD선진국 수준으로 개선한다는 목표를 세우고 있으나, 지역의 대기상태 및 그 동안의 대기질 개선을 위해 이행된 정책의 효율성 측면에서 볼 때 사후적인 규제위주의 농도규제 방식으로는 급증하는 대기오염배출시설의 배출량총량 관리가 어렵고, 지자체별로 개별적인 분산관리로는 광역적으로 이동되는 대기오염물질의 관리가 불가능하다. 또한 대기오염과 상관성이 큰 에너지정책, 산업정책, 도시계획 등 관련 정책과의 통합적 접근이 어렵기 때문에 사전에 이를 예방하는 총량관리가 요구되어 진다. 총량규제란 특정지역의 기상, 지형조건 등을 이용하여 대기환경용량을 산출하고 이를 기초로 지역별 배출허용총량을 할당하여 궁극적으로는 오염원별로 대상오염물질의 삭감량을 정하는 제도로 선진국에서는 대기환경용량을 바탕으로 1970년대부터 사업장을 중심으로 배출농도 규제와 함께 총량규제를 병행 실시하고 있으며, 최근에는 자동차에도 실시하고 있다. 우리나라에서도 대기환경보전법 제9조에서 환경기준을 초과하여 사람의 건강이나 재산, 동식물의 생육에 중대한 위해를 가져올 우려가 있다고 인정되는 경우에는 동 지역 또는 특별대책지역 중 사업장이 밀집되어 있는 구역에 대하여 배출되는 오염물질을 총량으로 규제할 수 있도록 규정하고 있다. 또한, 환경부는 2003년도에 서울, 인천, 경기도내 19개시 지역을 대상으로 대기오염물질의 배출총량을 관리하는 대기오염총량제 실시를 포함한 '수도권대기질개선에관한특별법'을 제정하였고, 현재는 사업장에게 연도별 배출허용총량을 할당하고, 할당량 이내로 오염물질을 배출하도록 관리하는 사업장 대기오염물질총량관리 제도로 시행 중에 있다. 그러나 수도권대기질개선특별대책을 수립하면서 총량관리의 본격 이행 및 배출권 거래제도 도입에 대한 특별법안이 제정되고 부분적으로 시행되고 있으나, 우리나라에 총량관리를 본격 이행하는데 있어서의 필요한 준비여건은 아직 초기 단계이고, 관련 연구의 수행실적 또한 수도권에 제한되어 적은 편이다. 따라서 현재는 총량관리가 수도권에 국한하여 실시되고 있으나, 점차 타 도시까지 광역적으로 확대될 것으로 예상되는 바 이에 필요한 제반 사항들에 대한 조사 분석을 통하여 정책방향을 설정하는 더 많은 연구가 필요할 것이다. 이러한 배경에서 본 연구에서는 대구지역을 대상으로 대기오염농도 및 대기오염물질 배출량에 대한 현황조사를 실시하고, 이를 토대로 고농도가 자주 발생되거나 그러할 가능성이 높은 $NO_X$을 대상으로 대기오염기여도를 평가하고 대기확산모델을 통한 대기환경용량을 산정하였다. 대기오염농도 현황을 살펴본 결과, 대구지역의 대기오염은 $NO_2$, $SO_2$, CO는 전형적인 1차오염물질의 변화경향을 보였으며, $PM_{10}$는 봄철에 황사의 영향을 크게 받는 것으로 나타나 실제 대구지역에서 배출되는 양을 추정하기 힘든 것으로 판단된다. 또한 $NO_2$는 공업, 상업지역에서 $SO_2$$PM_{10}$는 공업지역, CO는 상업지역, $O_3$은 교외지역에서 높은 농도를 나타내는 것으로 파악되었다. 대구지역의 대기오염물질 배출량 현황은 CO가 47%, NOX가 43%로 전체 배출량의 90%를 차지하였고, 2005년 이후 $NO_X$는 감소하고 $SO_X$가 증가하는 추세이다. 또한 배출원대분류 중도로 및 비도로이동오염원에서 발생되는 선 오염원이 75%로 대구지역에서 가장 크게 기여하는 것으로 나타났다. ISCST3 대기확산모델을 이용하여 대기환경용량을 산정하기위하여, 먼저 대구지역의 대기환경용량평가는 가시적인 위해성이 높고 개선정책이 용이한 $NO_X$을 대상물질로 선정하였고, 배출량과 오염농도간의 상관도가 0.659로 높은 것으로 판단되어, 배출량을 삭감하였을 때 대기오염농도의 개선이 명확히 나타나는 것을 알 수 있었다. 다음으로, 단위격자 당 한계배출율을 알아내는 작업을 실시하여, 대구지역을 동일하게 장기환경기준 80%수준인 22.4ppb를 만족시키기 위한 한계배출율은 2.23g/s가 필요한 것으로 파악되었고, 산출한 한계배출율을 이용하여 장기환경기준치 80%수준 달성을 목표로 하는 경우의 대기환경용량을 산정하고 실제 배출량과 비교 분석하였다. 그 결과, 대구지역 전체의 환경용량은 약 3만 톤으로 실제 배출량 2만2천 톤에 약 8천 톤 이상의 여유가 있는 것으로 파악되었다. 그러나 구역별로 상이한 차이를 보였으며, 이에 따른 구역별 개선정책이 필요할 것으로 사료된다. 대기환경용량을 파악한 후 단위격자 당 한계배출율을 초과하는 대상 지역을 추출하여 삭감한 결과 초과배출량의 80%를 삭감해야 대구지역 전체에서 50ppb이하 농도가 되는 것을 알 수 있었는데, 실제로 초과배출량의 80%를 삭감하는 것은 어려움이 있다고 판단되어, 대구지역을 동일한 %율로 삭감한 결과 30% 삭감했을 때 50ppb수준을 달성하였고, 50%삭감했을때 2007년 환경기준인 30ppb수준을 달성하였다. 또한 배출원대분류 중 기여율이 높은 도로와 비도로오염원을 50%삭감한 결과 도로이동오염원의 삭감만으로도 상당한 고 배출지역의 농도저감에 효과가 있는 것으로 파악되고, 비도로오염원을 포함하여 삭감하였을 때는 대구지역 전체에서 50ppb이하로 내려가는 것을 볼 수 있었다. 따라서 향후 총량규제의 실시에 맞추어 대구지역의 실제적인 환경용량의 정확한 파악과 고배출지역에 대한 삭감방법에 관한 더 많은 연구가 필요하다고 사료된다. 이 연구 결과는 앞으로 시행될 지역총량규제에 대한 기초적인 방법론으로 활용될 수 있을 것이다.

  • PDF

Fundamental Study for Extension of Application of Recycled Concrete Aggregate: Spun High Strength Concrete (순환골재의 사용성 확대를 위한 연구: 원심력콘크리트로의 적용)

  • Sim, Jong-Sung;Park, Cheol-Woo;Park, Sung-Jae;Kim, Hyun-Jung;Kim, Taeg-Wang;Lee, Man-Suk
    • Journal of the Korean Recycled Construction Resources Institute
    • /
    • v.2 no.1
    • /
    • pp.103-112
    • /
    • 2006
  • Along with recent improvement of recycling technique, the quality of the recycled concrete aggregate have become very competitive to the natural concrete aggregate. Therefore, a practical use of the recycled concrete aggregate may be possible for structural members. Majority studies about the recycled concrete aggregate was emphasized a limitation of fundamental study concerned with a strength characteristics and durability of the recycled aggregate concrete, there is use for the structural members. Therefore, for the extension of application of recycled concrete aggregate, this investigation verifies the strength characteristics recycled concrete aggregate of the spun-concrete products with various coarse and fine recycled aggregate replacement ratio(coarse recycled aggregate: 0%, 20%, 40%, 60%, 100%; fine recycled aggregate: 0%, 30%, 60%, 100%) and with addition of cellulose fibers(0%, 0.01%, 0.03%, 0.05%, 0.08%). From the test results, The strength of spun concrete used with recycled aggregate [NR specimen], was measured as 72MPa, was found to be very approximately to the strength of spun concrete used with the natural aggregate(NN specimen), was measured as 74MPa, when only fine aggregate was replaced with the recycled. Therefore, the fine recycled concrete aggregate can be successfully used in the spun high strength concrete product. The compressive strength of all specimens used the specialty cellulose fiber were measured as about 70M Pa, however, the increasement of the specialty cellulose fiber content is showed to decrease compressive strength of spun concrete. Therefore, it is anticipated that the specialty cellulose fiber can be applied to the various spun concrete products.

  • PDF

Influence of Fine Aggregate Properties on Unhardened Geopolymer Concrete (잔골재 특성이 굳지 않은 지오폴리머 콘크리트에 미치는 영향)

  • Cho, Young-Hoon;An, Eung-Mo;Lee, Su-Jeong;Chon, Chul-Min;Kim, Dong-Jin
    • Journal of the Korean Recycled Construction Resources Institute
    • /
    • v.4 no.2
    • /
    • pp.101-111
    • /
    • 2016
  • It is possible that aggregates add on to geopolymer based fly ash to mix mortar and concrete like cement. This is necessary to evaluate mineral composition, particle shape, surface, size distribution, density and absorption ratio for fine aggregates due to few detailed research to examine influence of fine aggregates properties on unhardened geopolymer concrete. In this research, used two different fine aggregates, Jumunjin sand(having quartz, mica, feldspar, pyroxene in mineral composition, more than 96% of total size between -0.60 and +0.30mm, angular shape and rough surface) and ISO sand(having almost all quartz in mineral composition, more than 51% size between -1.40 and +0.60mm, simultaneously varied size distribution, spherical shape and smooth surface). After an experimental result of the varied ratio of Si/Al=1.0-4.1 geopolymer paste, mix proportion respectively applied Si/Al=1.5 having the highest compressive strength to mortar and Si/Al=3.5 having the highest consistency to concrete. Geopolymer mortar by mixing with Jumunjin and ISO sand in varied range of 20-50wt.% showed flow size increase between 69.5 and 112.0mm, between 70.5 and 126.0mm respectively. Geopolymer concrete at an addition of 77wt.% of total aggregates ratio showed that average compressive strength was 32MPa and the consistency was favorable to molding. Since ISO sand observing varied size distribution, spherical shape, smooth surface, low absorption ratio resulted in advantageous properties on consistency of geopolymer, geopolymer concrete can be suitable for using the fine aggregates similar to ISO sand.

Sensitivity of NOx Removal on Recycled TiO2 in Cement Mortar (재생 이산화티탄을 혼입한 모르타르의 NOx 저감률 민감도 분석)

  • Rhee, Inkyu;Kim, Jin-Hee;Kim, Jong-Ho;Roh, Young-Sook
    • Journal of the Korean Recycled Construction Resources Institute
    • /
    • v.4 no.4
    • /
    • pp.388-395
    • /
    • 2016
  • This paper explores the photocatalytic sensitivity of cement mortar incorporated with recycled $TiO_2$ from waste water sludge. Basically, $TiO_2$ cluster sank down slowly to the bottom of cement mortar specimen before setting and hardening process. This leads the mismatch of $TiO_2$ concentration on the top and the bottom faces of a specimen. This poorly dispersed $TiO_2$-cement mortar naturally exhibits poor NOx removal efficiency especially on the top of cementitious structure. In architectural engineering application such as building or housing structures, one can simply filp over from the bottom so that more $TiO_2$ concentrated surface can be placed outward into the air. However, in highway pavement case, this could not be applicable due to in-situ installation of concrete pavement. Hence, the dispersion of $TiO_2$ cluster inside the cementitous material is getting important issue onto road construction application. To elaborate this issue, according to our results, silica fume, high-ranged water reducer, viscosity agent, blast furnace slag were not enhanced much of dispersion characteristics of $TiO_2$ cluster. The combination of foaming agent and accelerator of hardening with viscosity agent and small grain size of fine aggregate may help the dispersion of $TiO_2$ inside cementitious materials. Even though the enhanced dispersion were applied to the specimen, NOx removal efficiency doest not change much for the top surface of the specimen. This concurrently affected by the presence of tiny air voids and the dispersion of $TiO_2$ in that these voids could easily adsorbed NOx gas with the aid of large surface area.

A Study on the Sedimentation of Dredged Soils and Shape Changes of a Transparent Vinyl Tube by Filling Tests - Anti-Crater Formation - (준설토 주입방법에 의한 비닐튜브체의 퇴적 및 변형 특성 - 크레이터 방지 기술을 중심으로 -)

  • Kim, Hyeong-Joo;Sung, Hyun-Jong;Lee, Kwang-Hyung;Lee, Jang-Baek
    • Journal of the Korean Geosynthetics Society
    • /
    • v.13 no.2
    • /
    • pp.1-10
    • /
    • 2014
  • In this study, two different types of dredged fill injection methods are introduced and filling experiments were conducted to analyze the impact of each technique to the distribution and deposition of dredged soil fill and how it influence the final tube shape. Two transparent plastic tubes were fabricated to observe the deposition behavior of the deposited fill material. Both tubes measured 4.0 meters in length (L) and has vinyl tube diameters (D) of 0.5m and 0.7m. T-type and I-type inlet system are also introduced in this paper. The influence of this inlet systems to the distribution and deposition behavior of dredged soil fill inside the vinyl tubes were observed during the experiment. After the sedimentation of the slurry mixture, the water on top of the soil sediments are removed and the slurry mixture was re-injected into the vinyl tube, this process was carried out repeatedly. The shape changes of the vinyl tube, e.g. the changes in both tube height and width, are constantly monitored after each slurry injection and water draining phases. Crater formation was observed in the case of I-Type inlet system and a non-uniform sediment distribution occurred. For the diffusion deposit of soil particles to long distance are minimal shape technique using the T-Type inlet system. Therefore the undrain filling height ratio ($H/D_0$) was found to be around 0.54 to 0.64 and the horizontal strain ratio ($W/D_0$) ranges from 1.45 to 1.54. The filling soil height is proportional to dredged-material filling phases, but, horizontal strain ratio is constant or inversely reduced so that the center of tube body is raised in the upward direction.

A Feasibility Study on the Use of Liner and Cover Materials Using Sewage Sludge (하수슬러지의 차수재 및 복토재로의 이용타당성에 관한 연구)

  • 유남재;김영길;박병수;정하익
    • Journal of the Korean Geotechnical Society
    • /
    • v.15 no.2
    • /
    • pp.43-71
    • /
    • 1999
  • This research is an experimental work of developing a construction material using municipal wastewater sludge as liner and cover materials for waste disposal landfill. Weathered granite soil and flyash, produced as a by-product in the power plant, were used as the primary additives to improve geotechnical engineering properties of sludge. For secondary additives, bentonite and cement were mixed with sludge to decrease the permeability and to increase the shear strength, respectively. Various laboratory test required to evaluate the design criteria for liner and cover materials, were carried out by changing the mixing ratio of sludge with the additives. Basic soil properties such as specific gravity, grain size distribution, liquid and plastic limits were measured to analyze their effects on permeability, compaction, compressibility and shear strength properties of mixtures. Laboratory compaction tests were conducted to find the maximum dry densities and the optimum moisture contents of mixtures, and their effectiveness of compaction in field was consequently evaluated. Permeability tests of variable heads with compacted samples, and the stress-controlled consolidation tests with measuring permeabilities of samples during consolidation process were performed to obtain permeability, and to find the compressibility as well as consolidational coefficients of mixtures, respectively. To evaluate the long term stability of sludges, creep tests were also conducted in parallel with permeability tests of variable heads. On the other hand, for the compacted sludge decomposed for a month, permeability tests were carried out to investigate the effect of decomposition of organic matters in sludges on its permeability. Direct shear tests were performed to evaluate the shear strength parameters of mixed sludge with weathered granite, flyash and bentonite. For the mixture of sludge with cement, unconfined compression tests were carried out to find their strength with varying mixing ratio and curing time. On the other hand, CBR tests for compacted specimen were also conducted to evaluate the trafficability of mixtures. Various test results with mixtures were assessed to evaluate whether their properties meet the requirements as liner and cover materials in waste disposal landfill.

  • PDF

Optimizing Surfactant-Enhanced Solubilzation of LNAPL from Soil in Saturated Zone (포화지층내 저비중 비수용성 유기용매의 용해제거를 위한 계면활성제법의 최적 조작인자 도출)

  • 이재원;박규홍;박준범
    • Journal of the Korean Geotechnical Society
    • /
    • v.15 no.2
    • /
    • pp.153-164
    • /
    • 1999
  • The solubilization of BTEX was evaluated in aqueous surfactant solutions with and without several additives. Anionic surfactant(Sodium Dodecyl Sulfate, SDS) and nonionic surfactants (NEODOL(equation omitted)25-3 and $SOFTANOL\circledR-90$ were used as test surfactants. The effects of surfactant HLB(Hydrophile-Lipophile Balance) Number and hydrocarbon molar volume and polarity of BTEX on the MSR(Molar Solubilization Ratio), micelle-water partition coefficient of BTEX, and CMC(C,itical Micelle Concentration) were investigated. Optimizing treatment conditions applicable to enhanced solubilization was also studied by manupulating salinity or electrolyte control with additives of ethyl alcohol, hydrotrope, and electrolyte solution. The most effective surfactant for solubilization was found $SOFTANOL\circledR-90$, since HLB number of 13.6 is similar to those values of BTEX ranging between 11.4 and 12.2, which was also proved experimentally. Ethyl alchohol of 3% was the most effective additives in reducing CMC and improving solubilization among the conditions using SDS, NEODOL(equation omitted)25-3, and $SOFTANOL\circledR-90$ with three additives. The partitioning of BTEX between surfactant micelles and aqueous solutions was characterized by a mole fraction micelle-phase/aqueous phase partion coefficient, $K_m$. Values of log $K_m$. for BTEX compounds in surfactant solutions of this study range from 2.95 to 3.76(100mM SDS) and 2.95 to 3.49(117mM $SOFTANOL\circledR-90$. Log $K_m$ appears to be a linear function of log $K_{ow}$ for SDS and $SOFTANOL\circledR-90$. A knowledge of partitioning of BTEX in aqueous surfactant system can be a prerequisite for the understanding of the behavior of hydrophobic organic compounds in soil-water systems in which surfactants play a role in remediation of contaminated soil and facilitated transport.

  • PDF