• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.2
• /
• pp.331-346
• /
• 2018

In the tunnel of domestic high - speed railway, the main fire - fighting facility, fire - extinguishing passageway, is installed. However, due to the high pressure of the high - speed train, frequent breakage and maintenance are caused by strong shock and long - term vibration. In order to solve these problems, it is necessary to improve the fire door, but in Korea, it is installed by submitting a certificate by simple KS F 2296 performance test. At present, it is developed as a simple test certification by producing a real scale fireproof door without the theoretical examination in advance, so that a high cost for improvement is occurring in Korea. Therefore, through this study, structural analysis study which can preliminary structure review was carried out in order to design the refuge connection passage fire door and to improve the performance improvement. In order to secure the reliability of the result value, the official authentication test (KS F 2296) were compared.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.21 no.6
• /
• pp.887-895
• /
• 2019

Recently, the number of underground road development projects has been increasing to solve traffic problems in the national capital region and metropolitan areas with intensified overcrowding, and there has been a tendency to plan underground roads by applying a double-deck tunnel technology that has advantages in constructability and economical efficiency. The double-deck tunnel has a structure where one excavation section is divided into two parts and used as up and down lines, and is mainly used as a road for small vehicles only due to its low floor height. In addition, due to the small cross-sectional area, it has characteristics different from those of general road tunnels in terms of ventilation and disaster prevention. In this regard, this study proposed an operational plan that applies an oversized exhaust system, which is one of semi-transverse ventilation systems, to small cross-sectional tunnels like double-deck tunnel with low floor height, and a comparative analysis between smoke exhaust characteristics according to the fire occurrence locations and oversized exhaust systems was conducted using the Fire Dynamics Simulator (FDS). The results showed that unlike uniform exhaust, intensive smoke exhaust using the oversized exhaust port maximized the delay effect of smoke diffusion and limited the smoke within 50 m above and below the fire point.

• Journal of Korea Port Economic Association
• /
• v.29 no.4
• /
• pp.1-25
• /
• 2013

The purpose of this paper is to estimate economic benefits for the investment of railway transshipment system with non-powered turntable. The freight transport by railway can have decided advantages over trucks in terms of energy efficiency, emissions and cost for certain freight movements, just as transportation in the metropolitan region can have great advantages over driving truck. But the freight transport by truck should gain significant mobility benefits from a freight railway system. Thus, the railway transshipment system with non-powered turntable which is coupled railway transport advantages with load transport advantages has been developed and used in the european countries. This research has conducted the empirical analysis, by calculating the investment of railway transshipment system with non-powered turntable. The key factor for the economic benefits for the non-powered turntable is the utilizing throughputs. This demand is influenced by the throughput in the railway transshipment system. The main results of this paper are as follows: railway transshipment system with non-powered turntable does not have economic benefit for investment. We recommend that the plan for investment has to be considered the modification.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.16 no.2
• /
• pp.249-260
• /
• 2014

When a train enters the tunnel at high speed, the pressure wave occurs. When this pressure wave reaches at the exit of tunnel, some are either emitted to the outside or reflected in tunnel by the form of expansion wave. The wave emitted to the outside forms the impulsive pressure wave. This wave is called 'Micro Pressure Wave'. The micro pressure wave generates noise and vibration around a exit portal of tunnel. When it becomes worse, it causes anxiety for residents and damage to windows. Thus, it requires a counterplan and prediction about the micro pressure wave for high speed railway construction. In this paper, the effects of train head nose and tunnel portal shape were investigated by model test, measurement for the micro pressure wave at the operating tunnel as well as numerical analysis for the gradient of pressure wave in the tunnel. As results, a method for predicting the intensity of the micro pressure wave is suggested and then the intensity of the micro pressure wave is analyzed by the tunnel length and the cross-sectional area.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.16 no.2
• /
• pp.181-191
• /
• 2014

This study aims to evaluate cutter acting forces as well as axial stresses and torques in the shaft of two kinds of disc cutters including a single disc cutter and a double disc cutter with the same cutter ring geometry in a series of linear cutting tests. From the tests, the mean values of normal forces and rolling forces acting on the double disc cutter were approximately twice as high as those from the single disc cutter. Similarly, the mean values of axial stresses in the shaft of the double disc cutter were also twice as high as those from the single disc cutter even though the comparisons of torques from two kinds of disc cutters were insignificant since they showed very low values. However, it is necessary to take the durability of a tapered roller bearing used for the double disc cutter into high consideration since the average normal force from the double disc cutter exceeds the allowable force for a disc cutter with the diameter of 432 mm (17 inches). Finally, there is no practical problem in terms of axial stresses in the shaft of the double disc cutter since they are much lower than the yielding stress of the cutter shaft material, even though the axial stresses in the shaft of the double disc cutter are approximately twice as high as those from the single disc cutter.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.22 no.1
• /
• pp.135-144
• /
• 2020

Since the depth of tunneling with tunnel boring machine (TBM) becomes deeper and deeper, the expense for site investigation for coring and geophysical survey increases to obtain the sufficient accuracy. The tunnel ahead prediction methods have been introduced to overcome this limitation in the stage of site investigation. Probe drilling can obtain the core and borehole images from a borehole. However, the space in TBM for the probe drilling equipment is restricted and the core from probe drilling cannot reflect the whole tunnel face. Seismic methods such as tunnel seismic prediction (TSP) can forecast over 100 m ahead from the tunnel face though the signal is usually generated using the explosive which can affect the stability of segments and backfill grout. Electromagnetic methods such as tunnel electrical resistivity prospecting system (TEPS) offer the exact prediction for a conductive zone such as water-bearing zone. However, the number of electrodes installed for exploration is limited in small diameter TBM and finally the reduction of prediction ranges. In this study, the theoretical equations for the electrical resistivity survey whose electrodes are installed in the face and side of TBM to minimize the installed electrodes on face. The experimental tests were conducted to verify the derived equations.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.7 no.5
• /
• pp.73-78
• /
• 2007

It has been increasing that significant loss of life and property due to global wanning and extreme weather, and the climate and temperature changes in Korea Peninsula are now greater than the global averages. Climate information from regional climate models(RCM) at a finer resolution than that of global climate models(GCM) is required to predictclimate and weather variability, changes, and impacts. The new surface boundary conditions(SBCs) development is motivated by the limitations and inconsistencies of existing SBCs that have influence on model predictability. A critical prerequisite in constructing SBCs is that the raw data should be accurate with physical consistency across all relevant parameters and must be appropriately filled for missing data if any. The aim of this study is to construct appropriate SBCs for the RCM in Asia domain which will be used for the prevention of disasters due to climate changes. As all SBCs have constructed onto the 30km grid-mesh of the RCM suitable for Asia applications, they can be also used for other distributed models for climate and hydrologic studies.

• Journal of Institute of Convergence Technology
• /
• v.6 no.2
• /
• pp.35-40
• /
• 2016

Ignitor tip is a component of burner to start the burning process in power plant. This is used to ignite the coal to a constant operating state by fuel mixed with air and kerosene. This component is composed of three components so that air and kerosene are mixed in the proper ratio and injected uniformly. Because the parts with the designed shape are manufactured in the machining process, they have to be made of three parts. These parts are designed to have various functions in each part. The mixing part mixes the supplied air and kerosene through the six holes and sends it to the injecting part at the proper ratio. The inject part injects mixed fuel, which is led to have a constant rotational direction in the connecting part, to the burner. And the connecting plate that the mixed fuel could rotate and spray is assembled so that the flame can be injected uniformly. But this part causes problems that are worn by vibration and rotation because it is mechanically assembled between the mixing part and the inject part. In this study, 3D printing method is used to integrate a connecting plate and an inject part to solve this wear problem. The 3D printing method could make this integrated part because the process is carried out layer by layer using a metal powder material. The part manufactured by 3D printing process should perform the post process such as support removal and surface treatment. However, while performing the 3D printing process, the material properties of the metal powders are changed by the laser sintering process. This change in material properties makes the post process difficult. In consideration of these variables, we have studied the optimization of manufacturing process using 3D printing method.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2002.05a
• /
• pp.46-48
• /
• 2002

본 연구는 신문지 고지의 점착성 이물질 중 Primary Stickies의 정 량에 관한 것으로 서, 실제 신문지료를 화상분석하여 실시간으로 매크로크기의 점착성 이물질올 측정할 때 효율적인 측정조건을 탐색하여 제지공정의 l 현장에서 일차 점착성 이물질을 정량 하는 새로운 측정기의 측정 기준을 제시하고자 하였다. 이물질이란 제지공정에 의도적으로 첨가되지 않은 불질의 총칭으로 dirt 및 각종 점착 성 이물질 즉, stickies를 들 수 있다. 이 가운데 스틱키{stickies}란 부드럽고, 점착성을 나타내는 이물질의 총청으로 주로 점착제와 확스에 의해 형성된다. 스틱키는 고지 재활 용의 효율성을 가장 크게 저해하는 이물질로 와이어, 펠트 및 기타 공정요소에 부착되 어 초지 시 지절을 발생시킴으로써 생산성을 저하시킬 뿐 아니라, 외관상 상품가치와 인쇄적성올 저하시키며, 최종 제품의 강도적 물성 및 가공적성에도 영향을 미친다. 특 히 국내에서는 원가절감을 위해 고지의 재활용율올 증대시키고자 전력을 다하고 있으 며 환경보호 및 용수 절감올 위해 공정수를 절감하고 궁극적으로는 무방류화를 목표로 하고 있어 토지 계 내의 점착성 이물질의 투입과 농축 현상이 심각하게 진행되고 있는 실정이다. 초지공정에서 발생하는 스틱키 즉 점착성 이물질은 미세한 스크린의 슬롯 폭인 0.15 - -0.3mm 이상의 크기를 가져 스크린에 의해 분리될 수 있는 매크로 스틱키{macro s stickies}와 이보다 작은 마이크로 스틱키(micro stickies)로 크게 분류된다. 즉 매크로 스틱키는 스크린에 의해 분리될 수 있으나 마이크로 스틱키는 스크린을 통하여 기계적 으로 분리할 수 없다는 문제점을 지니고 있다. 스틱키는 또 거동 특성에 따라 primary s stickies와 secondary stickies로 구분할 수 있다. primary stickies는 펄핑과정에서 점착 성 이물질이 파괴됨에 따라 나타나지만, secondary stickies는 지류 제지공정의 백수에 용해 되거나 분산된 상태인 1때1 이하의 콜로이 드로 폰재 한다. 이 러 한 secondary stickies 는 pH, 온도의 변화나 각종의 첨가제에 의해 웅집이나 홉착 등을 발생할 수 있는 잠재 적 문제점 등을 가지고 있다. 예를 들어 양성 고분자의 첨가는 펄프 섬유를 웅집시킬 뿐 아니라 지료에 함유된 secondary dtickies의 안정성을 저하시켜 응집, 침적시키는 작용을 한다. 따라서 분리가 어렵고, 제지공정에서 문제를 일으키기 쉬운 2차 스퇴키를 적절히 제어하기 위한 기술 개발은 용수절감 뿐 아니라, 초지공정의 침적물 절감을 통 한 공정개선에도 매우 중요한 요소기술이라 할 수 있다.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.10 no.1
• /
• pp.35-42
• /
• 2010

The rapid economic development induced the massive road constructions, becoming bigger and high-speed of the vehicles. However, it brings lots of social problems, such as air pollutions, traffic noise and vibration. Special concrete block for the base course of asphalt pavement is needed to decrease traffic noise such as tire's explosive and vehicles sound, applying Helmholtz Resonators theory to asphalt pavement. If it is applied to the area where it happens considerable noise such as a junction, the street of a housing complex and a residential street, it is one of considerable method to solve the social requirements of noise problem. This research examines couple of laboratory tests for the sound absorption effect of the concrete block and the base concrete block. There are specimens which is fixed hall-size, space, depth as the condition of this research, and these are analysed of noise decrease effect using different condition of the first noise of each vehicle. As a result of analysis data according to vehicle noise volume, measurement distance, a form and size of the hall using the base concrete block, the use of special concrete base showed a good alternative solution for decreasing traffic noise level, from 4 dB to 9 dB.