• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.11a
• /
• pp.217-219
• /
• 2012

In this study, the experiment was conducted in the level of mortar as one of the basic studies on pre-cast concrete which acceleration curing is not done. This study has the purpose to develop the strength of mortar into 20MPa within 6 hours in the condition of room temperature using admixtures which can accelerate C3S hydration reaction. In this experiment, W/C was fixed into 20%, PCE which can stimulate C3S was used as an accelerating admixture. From the results of this experiment, maximum content of accelerating admixture was 1%. Also, as more than 20MPa was measured through 6-hour compressive strength, it can be known that strength can be developed without steam-curing.

• Magazine of the Korea Concrete Institute
• /
• v.9 no.4
• /
• pp.125-135
• /
• 1997

경량기포콘크리트란 시멘트슬러리 속에 미리 생성된 기포를 혼합시켜 양생시킴으써 동일한 체적의 보통콘크리트보다 가볍게 만든 콘크리트를 의미한다. 따라서 경량기포콘크리트는시멘트풀 결합재내에 기포가 무작위로 분포된 복합재료이다. 본 연구의 목적은 이러한경량기포콘크리트의 탄성계수 추정식을 미시역학적 이론을 바탕으로 추정하는데 있다. 이르 위해 본 논문에서는 미시역학적인 미분법에 Hansen의 수정기법을 적용한 수정미분법을 사용하여 경량기포콘크리트의 탄성계수 추정식을 제안하였다. 제안된 추정식을 사용하여 얻어진 결과는 실험결과와 잘 일치하였고 기존의 어떤 추정식보다도 우수한 결과를 보였다.

• Journal of the Korean Ceramic Society
• /
• v.38 no.5
• /
• pp.446-453
• /
• 2001

본 논문에서는 석고형태에 따른 belite-rich cement(BRC)의 수화성상 및 혼화제의 흡착거동으로부터 시멘트의 유동성에 미치는 영향성을 조사하였다. 또한, 보통 포틀랜드 시멘트(OPC)의 경우와도 그 영향성을 비교 검토하였다. 유동특성을 측정한 결과, 폴리카르복실산계 혼화제 사용시 반수와 이수석고를 첨가한 BRC가 미니슬럼프 값이 약 $\pm$20cm 근방의 수치를 보였으며, 무수석고를 첨가한 것과 OPC에서는 낮은 슬럼프치를 보였다. 초기 수화의 경우, XRD와 DSC에서 Ca(OH)$_2$의 생성량의 정도가 BRC 2-C(반수)>BRC 1-C(이수)>BRC 3-C(무수)의 순서로 줄어들기 때문에 장기강도측면에서도 반수석고와 이수석고를 동시에 사용하는 것이 우수할 것으로 추정된다. 또한 이 결과는 비표면적의 데이터와도 일치함을 보였다.

• Journal of the Korean Ceramic Society
• /
• v.35 no.5
• /
• pp.479-485
• /
• 1998

Raw mateials such as limestone quartzite bauxite and anhydrite were used in the production of mod-ified beloite cement. Two kinds of clinker were synthesized with relatively higher content of $C_2S$ than that of $C_4A_3{\={S}}$ Concerning $C_2S$ the main mineral component borax ($Na_2O\;2B_2O_3\;10H_2O$) was added to stimu-late hydraulic reactivity and this would be possible by stabilizing ${\alpha}'-C_2S$ at room temperature. We had in-tended to compare burning and hydraulic characteristics of clinkers with one another by varying the amount of borax addition and to study the appropriate amount of anhydrite addition needed in the strengthening of cement during hydration. It was concluded that the effective amount of borax addition ne-eded for stabilization of ${\alpha}'-C_2S$ was 5 wt% in 60wt% $C_2S$ inclusive clinker and adding anhydrite in the ra-tio of 1.3 of $SO_3/Al_3O_3$ was appropriate in the production of cement by this clinker. Only ettringite was seen to contribute to the strength without additives but C-S-H was found to form along with ettringite with the addition of borax in the initial stage of hydration.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.1
• /
• pp.80-87
• /
• 2020

The purpose of this study is to investigate the physical properties and self-healing effects of hardener-free epoxy-modified mortars(EMMs) using ground granulated blast furnace slag(GGBFS). The EMMs with GGBFS were prepared with various polymer-binder ratios and GGBFS contents, and tested for strengths, adhesion in tension, water permeation and self-healing effects. The conclusions obtained from the test results are summarized as follows. The compressive strength of the EMMs with GGBFS is reduced with increasing polymer-binder ratios because of reduction of the degree of hardening in the EMMs, and is somewhat inferior to that of unmodified mortars. In the flexural and tensile strengths, the flexural strength of the EMMs is almost constant with increasing polymer-binder ratios. However, the tensile strength of the EMMs is gradually increased with increasing polymer-binder ratios. Regardless of the GGBFS contents, the adhesion in tension of the EMMs increases sharply with increasing polymer-binder ratios. The water permeation of the EMMs is remarkably reduced with increasing polymer-binder ratios and GGBFS contents. The self-healing effect of the hardener-free EMMs with GGBFS is improved with increasing water immersion period at a GGBFS content of 20%.

• Journal of the Korea Concrete Institute
• /
• v.16 no.1 s.79
• /
• pp.1-9
• /
• 2004

This paper represents the permeability of chloride ions and the corrosion performance in the concrete blended with granulate blast furnace slag exposed to chloride environment. An ordinary cement (type I ) and sulfate resisting cement(type V) were used for the experiment. The two cements were combined with $0\%$, $25 \%$, $40\%$, and $55\%$ of the granulated blast furnace slag. The accelerated permeability tests of chloride ions were performed in accordance with ASTM C1202, and the accelerated corrosion tests of steel were carried out by using the method of immersion/drying cycles. After water curing 28 days, 56 days and 91 days, these tests were conducted until 30 cycles. In every cycle, test specimens were wetted in $3\%$ NaCl solution for three days and dried again in $60^{\circ}C$ air for four days. As an experimental results, the diffusion coefficient of chloride ions of the ordinary cement Concrete Combined granulated blast furnace slag was much lower than that of non granulated blast furnace slag concrete. Moreover, the diffusion coefficient of chloride ions of sulfate resisting cement concrete was higher than that of ordinary cement concrete. On the basis of the results of accelerated corrosion tests, corrosion resistance of the concrete mixed with granulated blast furnace slag shows good to corrosion resistance, however, the concrete with sulfate resisting cement shows bad to corrosion resistance.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.26 no.3
• /
• pp.311-322
• /
• 2010

The purpose of this study was to evaluate the bond strengths between IPS e.max Press and four different types of resin cements that often used for esthetic restoration. Disc shaped IPS e.max Press blocks(N=40, diameter: 12mm, thickness: 3mm) were fabricated according to the manufacture's instruction and cleaned with ultrasonic cleaner. They were embedded into an autopolymerizing acrylic resin. Fourty cylinder shaped resin block(Filtek Z350, diameter: 4.5mm, thickness: 3mm) were fabricated using a plastic tube. Each specimens were randomly divided into 4 experimental group and bonded each other using 4 different resin cements(Variolink II(light-cure), Variolink II(dual-cure), Calibra, Super-Bond C&B) according to the manufactures' recommendations. All the specimens were stored in normal saline at $37^{\circ}C$ for 24 hours before test. Universal testing machine at a crosshead speed of 1mm/min was used to evaluate the shear bond strength. The data were statistically analyzed using one-way ANOVA(P<.01). Multiple comparison was done by the Tukey HSD test. The shear bond strength of Super-Bond C&B to e.max was significantly lower than those of Calibra, Variolink II(light-cure), Variolink II(dual-cure) (P<.01). The shear bond strength of Calibra, Variolink II(light-cure), Variolink II(dual-cure) to e.max were not significantly different. The shear bond strengths of light-cure/dual-cure cement were higher than that of self-cure cement.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2000.10a
• /
• pp.290-295
• /
• 2000

Mechanical and physical properties of wood fiber for the reinforcement of thin-sheet cement products were investigated. The slurry-dewatering method followed by pressing was used to manufacture the products. Mechanical and physical properties of wood fiber reinforced cement composites were assessed with flexural strength, density, and water absorption. The results obtained in this study were analyzed statistically using the analysis of variance in order to derive statistically reliable conclusions.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.525-528
• /
• 2008

This study is performed to know influence on the hydration according to alkali activator and method of pulverization and fineness in slag-cement. The compressive strength of mortar were examined when the SG powder of which the specific surface area are 4,000, 6,000, and 8000cm$^2$/g were substituted for 50wt.% of ordinary portland cement. Na$_2$SO$_4$, Ca(OH)$_2$, NaOH were used as alkali activator. respectively, As the results, the compressive strength of mortar increased as following the order, Na$_2$SO$_4$>Ca(OH)$_2$>None>NaOH until 7days. But at 28days, mortar used Ca(OH)$_2$ as alkali activator were the highest strength.

• Journal of the Korea Concrete Institute
• /
• v.15 no.6
• /
• pp.778-784
• /
• 2003

The carbonation of concrete is one of the major factors that cause durability problems in concrete structures. The rate of carbonation depends largely upon the diffusivity of carbon dioxide in concrete. The purpose of this study is to identify the diffusion coefficients of carbon dioxide for various concrete mixtures. To this end, several series of tests have been planned and conducted. The test results indicate that the diffusion of carbon dioxide reached the steady-state within about five hours after exposure. The diffusion coefficient increases with the increase of water-cement ratio and decreases with the increase of relative humidity at the same water-cement ratio. The content of aggregates also influences the diffusivity of carbon dioxide in concrete. It was found that the diffusion coefficient of cement paste is larger than that of concrete or mortar. The experimental study of carbon dioxide diffusivity in this study will allow more realistic assessment of carbonation depth in concrete structures.