• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.255-255
• /
• 2015

국제핵융합실험로(ITER)의 3대 목표 중 하나는 핵융합로 개발을 위한 삼중수소증식블랑켓 개념을 시험하고 검증하는 것이며, 이를 위해 시험증식블랑켓(TBM, Test Blanket Module) 프로그램을 마련, 각국이 참여할 수 있도록 하고 있다. 한국도 2012년 국가핵융합위원회 결정에 따라, EU, 일본, 중국, 인도와 함께 TBM 프로그램에 참여하고 있으며, 2021년 설치를 목표로 헬륨냉각 고체증식재 개념의 HCCR (Helilum Cooled Ceramic Reflector) TBM을 설계, 개발하고 있다. 한국형 TBM은 총 4개의 서브모듈과 하나의 후벽(Back Manifold, BM) 으로 구성되며, 각 서브모듈은 플라즈마와 대면하는 일차벽(First Wall, FW), 증식재와 증배재, 반사재를 담고 있는 증식영역(Breeding Zong, BZ), 냉각재 매니폴드 및 구조물 역할을 하는 측벽(Side Wall, SW) 등의 기능부품으로 구성되어 있다. 냉각재는 8 MPa, $300-500^{\circ}C$의 고온고압헬륨을 사용하고, Li2SiO4 혹은 Li2TiO4 형태의 Li 세라믹 증식재를 사용하며, 중성자 증배를 위해 Be 증배재 및 흑연 반사재를 사용한다 [1-3]. 2015년 2월 개념설계검토(CDR, Conceptual Design Review)를 위해, TBM-shield를 포함한 TBM-set 설계가 완료되었으며, 열수력, 구조, 지진, 전자기, 복합하중에 대한 평가가 진행되었다. 본 논문에서는 이 중 H/He-phase에 시험될 EM-TBM과 D-T phase에 시험될 INT-TBM에 대한 열수력 성능 결과를 소개하였다[5]. 각각의 열부하 조건은 0.17과 $0.3MW/m^2$이며, 중성자 조사는 D-T phase 에서만 고려되었다. 구조재 및 사용된 기능소재별 온도 요건을 정의하고, 성능해석 결과와 비교하였으며, 이를 통해 모든 온도 요건을 만족함을 최종 확인하였다. 이러한 온도 분포는 열응력 평가를 위해 구조해석 입력자료로 활용되었다.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.16 no.3
• /
• pp.142-151
• /
• 2004

A method for the determination of concrete armor unit weights with hydraulic stability and structural stability may be formulated in this paper. The hydraulic stability is analyzed by using Hudson's formula, the structural stability is also studied by evaluation of maximum flexural tensile stresses in armor unit induced by the impact loads and by comparison of those with the tensile resistance strength directly. The applicable criteria for concrete armor units can be represented as a function of design wave heights with return period, armor weights, and tensile strengths for the practical uses. In addition, reliability analyses for two failure modes are carried out to take into account some uncertainties. Finally, a series system for two-failure mode analysis can be made up straightforwardly, by which the optimal weights of armor units can be estimated with the various relative breakages, given the specific target probability of failure under the concepts of reliability-based design method.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.6
• /
• pp.2804-2811
• /
• 2012

In this study, It is developed a retrofitting procedure of RC column with rectangular section to archive the target displacement at failure. Nonlinear behavior of the column is considered as the equivalent linear system. First, target displacement is determined, and then elastic displacement spectrum is constructed to estimate the equivalent natural vibration period of the SDOF system. After natural vibration period is determined, required strength is calculated using secant stiffness based on the mass of system. In accordance with, obtained force-displacement relationship through non-linear fiber based section analysis, retrofit design was carried out to meet required strength. As a result, retrofitted RC column can confirm that the improved seismic performance. It is observed that the proposed design procedure can be applicable to seismic retrofitting design of columns.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.8
• /
• pp.703-710
• /
• 2012

At the stage of conceptual design of a helicopter, it is a general way using low fidelity analysis methods because of a large number of design calculations and trade-off studies. Determination of empirical parameters used in analysis codes for more practical design, depends on an user's design experiences, which effects on the accuracy and the fidelity of conceptual design results. Thus, more precise and logical method should be required to determine the empirical parameters used in the conceptual design of a helicopter. The present method is to be used not only in verifying the empirical parameters generated by design requirements, but also regenerate them if they contain any errors. Empirical parameters produced by present method were used to design a helicopter with a payload objective and performance constraints of an operating helicopter. As a result, weights and geometries of designed helicopter matched the target value within 5% significance level, proving that the suggested parameter generating method can be useful in the conceptual design of a helicopter.

• Journal of the Korea Concrete Institute
• /
• v.27 no.1
• /
• pp.29-35
• /
• 2015

Recent studies to develop Very Large Floating Structure(VLFS) has shown that the construction procedure of the structure needs to acquire precast concrete module connection system using prestressing. However, the loads occurring on water are complex combinations of various condition, so the safe and stable performance of the module joints and bonding materials are key to the success of the construction. Therefore, micro-silica mixed aqua-epoxy development was introduced in Part 1 using a bonding material developed in this study. The performance of the micro-silica mixed aqua-epoxy(MSAE) applied joint of concrete module specimens connected by prestressing tendon was evaluated to verify the usability and safety of the material. RC beam, spliced beam connected by prestressing tendon and MSAE, and continuous prestressed concrete beam were tested for their initial cracking and maximum loads as well as cracking procedure and pattern. The results showed that the MSAE can control the stress concentration effect of the shear key and the crack propagation, and the maximum load capacity of MSAE joint specimens are only 5% less than that of continuous RC specimen. The details of the study are discussed in detail in the paper.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.2 no.3
• /
• pp.87-99
• /
• 1982

This study proposes a reliability based design criteria for the R.C. superstructures of highway bridges. Uncertainties associated with the resistance of T or rectangular sections are investigated, and a set of appropriate uncertainties associated with the bridge dead and traffic live loads are proposed by reflecting our level of practice. Major 2nd moment reliability analysis and design theories including both Cornell's MFOSM(Mean First Order 2nd Moment) Methods and Lind-Hasofer's AFOSM(Advanced First Order 2nd Moment) Methods are summarized and compared, and it has been found that Ellingwood's algorithm and an approximate log-normal type reliability formula are well suited for the proposed reliability study. A target reliability index (${\beta}_0=3.5$) is selected as an optimal value considering our practice based on the calibration with the current R.C. bridge design safety provisions. A set of load and resistance factors is derived by the proposed uncertainties and the methods corresponding to the target reliability. Furthermore, a set of nominal safety factors and allowable stresses are proposed for the current W.S.D. design provisions. It may be asserted that the proposed L.R.F.D. reliability based design criteria for the R.C. highway bridges may have to be incorporated into the current R.C. bridge design codes as a design provision corresponding to the U.S.D. provisions of the current R.C. design code.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.27 no.4
• /
• pp.281-288
• /
• 2014

As a gas explosion is the most fatal accident in shipbuilding and offshore plant industries, all safety critical elements on the topside of offshore platforms should retain their integrity against blast pressure. Even though many efforts have been devoted to develop blast-resistant design methods in the offshore engineering field, there still remain several issues needed to be carefully investigated. From a procedure for calculation of explosion design pressure, impulse of a design pressure model having completely positive side only is determined by the absolute area of each obtained transient pressure response through the CFD analysis. The negative pressure phase in a general gas explosion, however, is often quite considerable unlike gaseous detonation or TNT explosion. The main objective of this study is to thoroughly examine the effect of the negative pressure phase on structural behavior. A blast wall for specific FPSO topside is selected to analyze structural response under the blast pressure. Because the blast wall is considered an essential structure for blast-resistant design. Pressure time history data were obtained by explosion simulations using FLACS, and the nonlinear transient finite element analyses were performed using LS-DYNA.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.1
• /
• pp.447-455
• /
• 2019

When constructing LNG storage structures using the cast-in-place method in extreme areas, the construction cost and time may be increased due to the poor working environments and conditions. Therefore, demand for modular energy storage tanks is increasing. In this study, we propose using an SCP module as an alternative for lighter-weight LNG storage tanks. The purpose of this study is to evaluate the feasibility of LNG storage outer tanks by performing bending tests on the thickness of composite steel plate concrete under field conditions. The loads on specimens with thicknesses of 100 mm and 200 mm were linearly increased to the design final loads of 413 kN and 822 kN, respectively. The slope was rapidly changed, and fracture occurred. The two test conditions showed linear behavior until the steel plate yielded, and after an extreme load behavior, sudden yielding of the steel plate yield occurred in the SCP bending test according to the INCA guidelines. The results satisfied the design flexural load and showed the possibility of using the specimens in a modular LNG outer tank. However, it is necessary to evaluate the structural performance of the SCP by performing compression and shear tests in future research.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.6
• /
• pp.672-680
• /
• 2023

Weight is a critical factor in the ship design process given that it has a substantial impact on the hydrodynamic performance of ships. Typically, ships are optimally designed for specific conditions with a fixed draft and displacement. However, in reality, weight and draft can vary within a certain range owing to operational activities, such as fuel consumption, ballast adjustments, and loading conditions . Therefore, we investigated how resistance changes under three different loading conditions, namely overload, design-load, and lightship, for small craft, using both model experiments and numerical simulations. Additionally, we examined the sensitivity of weight changes to resistance to enhance the performance of ships, ultimately reducing power requirements in support of the International Maritime Organization's (IMO) goal of reducing CO2 emissions by 50% by 2050. We found that weight changes have a more significant impact at low Froude Numbers. Operating under overload conditions, which correspond to a 5% increase in draft and an 11.1% increase in displacement, can lead to a relatively substantial increase in total resistance, up to 15.97% and 14.31% in towing tests and CFD simulations, respectively.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.1 no.1
• /
• pp.21-32
• /
• 1981

Recent trends in design standards development in some European countries and U.S.A. have encouraged the use of probabilistic limit sate design concepts. Reliability based design criteria such as LSD, LRFD, PBLSD, adopted in those advanced countries have the potentials that they afford for symplifying the design process and placing it on a consistent reliability bases for various construction materials. A reliability based design criteria for RC flexural members are proposed in this study. Lind-Hasofer's invariant second-moment reliability theory is used in the derivation of an algorithmic reliability analysis method as well as an iterative determination of load and resistance factors. In addition, Cornell's Mean First-Order Second Moment Method is employed as a practical tool for the approximate reliability analysis and the derivation of design criteria. Uncertainty measures for flexural resistance and load effects are based on the Ellingwood's approach for the evaluation of uncertainties of loads and resistances. The implied relative safety levels of RC flexural members designed by the strength design provisions of the current standard code were evaluated using the second moment reliability analysis method proposed in this study. And then, resistance and load factors corresponding to the target reliability index(${\beta}=4$) which is considered to be appropriate level of reliability considering our practices are calculated by using the proposed methods. These reliability based factors were compared to those specified by our current ultimate strength design provisions. It was found that the reliability levels of flexural members designed by current code are not appropriate, and the code specified resistance and load factors were considerably different from the reliability based resistance and load factors proposed in this study.