• Journal of the Korean Wood Science and Technology
• /
• v.45 no.5
• /
• pp.599-612
• /
• 2017

Human hair (HH) is produced as a waste from beauty parlor and barbershop. HH-based adhesives were formulated with NaOH-hydrolyzed HH, $H_2SO_4$-hydrolyzed chicken blood (CB) and PF as a crosslinking agent. Physicochemical properties and retention rate against hot water of the adhesives were measured to investigate the potential of HH as a raw material of wood adhesives. HH was composed of keratin-type protein of 80% and over. Ash of less than 0.1% was contained in HH. Among the amino acids included in HH, glutamic acid showed the highest content, followed by cysteine, serine, arginine and threonine. Solid content of the adhesives ranged from 33.2% to 41.8% depending on hydrolysis conditions of HH and PF type. Viscosity at $25^{\circ}C$ ranged from 300 to $600mPa{\cdot}s$ resulting in a sprayable adhesive. Retention rate against hot water measured to evaluate the water resistance of adhesives was the highest in the cured resin formulated with 5% NaOH-hydrolyzed HH and 5% $H_2SO_4$-hydrolyzed CB. Meanwhile, the molar ratio of formaldehyde to phenol in PF did not have a significant impact on the retention rate of HH-based adhesives. When the retention rates of HH-based adhesives were compared to those of conventional wood adhesive resins used for the production of wood-based panels extensively, HH-based adhesives formulated with 30 wt% PF showed lower retention rate than commercial urea-formaldehyde resin. However, when PF content was increased to 35 wt%, the retention rate greatly increased and approached to that of commercial melamine-urea-formaldehyde resin. Except for the results mentioned above, the analysis of economic feasibility suggests that HH-based adhesives can be used for the production of wood-based panels if HH is hydrolyzed in proper conditions and then the HH-based adhesives are formulated by the HH hydrolyzates with 35 wt% PF.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.4
• /
• pp.323-332
• /
• 2010

Petroleum-based adhesive resins have extensively been used for the production of wood panels. However, it is necessary to develop environmentally friendly adhesive resins due to the increase of manufacturing cost and the environmental issue, such as the emission of volatile organic compounds, of the pertroleum-based adhesive resins. This study was conducted to formulate environmentally friendly adhesive resins using by rapeseed flour (RSF), which is the by-product of bio-diesel produced from rapeseed, for replacing petroleum-based adhesives with them. To formulate RSF-based adhesive resins, RSF was hydrolyzed in de-ionized water, 1% and 3% sodium hydroxide solutions. As a crosslinking agent, PF prepolymers were prepared with 1.8, 2.1 and 2.4 mol formaldehyde and 1 mol phenol (1.8-, 2.1- and 2.4-PF), and then mixed with RSF hydrolyzates to complete the formulation of RSF-based adhesive resins. The RSF-based adhesive resins were applied to fabricate 3-ply plywood panels. The solid content of RSF-based adhesive resins were ranged from 26.08% to 36.12% depending on the hydrolysis condition of RSF and PF prepolymer type with a high viscosity. The tensile shear strength and wood failure of plywood fabricated with RSF-based adhesive resins exceeded a minimum requirement of KS standard for ordinary plywood regardless of the hydrolysis condition of RSF and PF prepolymer type. Formaldehyde emissions of the plywood panels fabricated with 1.8-PF and RSF hydrolyzates were lower than that of E0 specified in the KS standard. Based on the results, RSF might be used as a raw material of environmentally friendly adhesives for the production of plywood panels, but further researches - the increase of solid content of RSF-based adhesives for reducing press time and the microscopic observation of plywood specimen for identifying the relationship between tensile shear strength and the penetration of adhesives into wood structure - are required to commercialize the RSF-based adhesives.

• Journal of the Korean Wood Science and Technology
• /
• v.40 no.3
• /
• pp.164-176
• /
• 2012

In the present study, rapeseed flour (RSF), which is a by-product from the production of edible oil and biodiesel extracted from rapeseed, was used to develop alternative adhesives for the production of plywood panels. To examine the effects of the enzyme on the adhesive properties and formaldehyde emission of the RSF-based adhesive resins, three enzymes, such as cellulase (CEL), pectinase (PEC) and protease (ALC), were used either separately or together. As a crosslinking agent, PF prepolymers, which were prepared with 1.5, 1.8 and 2.1 mole formaldehyde and 1 mol phenol (1.8-, 2.1- and 2.4-PF), were added into the RSF hydrolyzates. The adhesive resins formulated with CEL- or CEL-PEC-RSF hydrolyzates and 1.8-F/P PF prepolymers exhibited excellent adhesive strengths and formaldehyde emission. The tensile shear strength and formaldehyde emission of the plywood panels bonded with the formulate resins were satisfied with the minimum requirement of the KS standard for ordinary plywood panels (0.6 N/$mm^2$). In addition, formaldehyde emissions of the plywood panels approached to that of E0 specified in the KS standard (0.5 mg/${\ell}$), and even had much better than those of commercial UF glue mixes. Overall, the use of RSF-based adhesive resins for the production of plywood panels might provide durable adhesive properties and an environmentally friendly substitute for petroleum-based adhesive resins. However, further researches - the increase of solid content of RSF-based adhesives for reducing press time and the microscopic observation of plywood specimen for identifying the relationship between tensile shear strength and the penetration of adhesives into wood structure - are required to commercialize the RSF-based adhesives.

• Journal of Korean Society of Forest Science
• /
• v.30 no.1
• /
• pp.8-18
• /
• 1976

This study was carried out to exploit and utilize the exotic American Sycamore(Platanus occidentalis) grown in Korea as a veneer species for plywood manufacture. At present most parts of veneer Legs used in Korea were depended entirely upon the gonus Shorea woods(lauan logs) imported from Southeast Asia region. To decrease manufacturing cost and save imported lauan veneer logs, the effects on properties affecting to the six types of plywood made from proper veneer constructions composed by domestic American Sycamore and imported lauan veneers were compared and discussed. The study has important meanings for the promotion of plywood manufacture by domestic materials. Important items dealt with this study were dry and wet shear strength, moisture contents, specific gravties, and bending strength. By the results and discussions it may be summarized as follows: 1) In dry shear strength platanus(sycamore) core lauan plywood was shown most excellent strong results, and next orders were all lauan plywood, platanus faced lauan plywood, lauan core platanus plywood, lauan faced platanus plywood, and all platanus plywood. There was no difference between platanus core lauan plywood and all lauan plywood, but the differences between those plywoods and the other types of plywood were recognized. 2) In wet shear strength platanus core lauan plywood was shown excellent result the same as dry strength. The difference between platanus core lauan plywood and the other types of plywood was shown, but among the other types of plywood except platanus core lauan plywood were not recognized. 3) The differences among moisture contents according to the veneer construction were not recognized. 4) The plywood constructed by two or more sheets of lauan veneer was shown lower specific gravities than the plywood constructed by two or more sheets of platanus veneer. It is believed that this tendency due to the original specific gravities of veneer before construction. 5) The differences among specific gravities of lauan core platanus plywood, all platanus plywood and lauan faced platanus plywood were not recognized, and like this analyzed result among platanus core lauan plywood, all lauan plywood and platanus faced lauan plywood were not recognized. Accordingly it is believed that the differences are not shown among the plywood constructed by two or more veneers of same species. 6) In bending strength platanus core lauan plywood was shown most excellent values. Next orders were all lauan plywood, platanus faced lauan plywood and the other types of plywood. The differences among the plywood constructed by two or veneers of lauan were shown, but not shown among the plywood constructed by tow or more veneers of platanus.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.46 no.6
• /
• pp.85-96
• /
• 2018

Developed nations have implemented various policies to reduce greenhouse gases since the 1997 Kyoto Protocol in order to minimize the effects of global warming. Korea should also reduce energy consumption in the industrial sector, and the transportation and building sectors in order to achieve its greenhouse gas reduction target of 37 percent compared to the Business As Usual levels. The government implements various laws and regulations for reducing energy consumption. To reduce energy consumption in the building sector, in particular, the Energy Conservation Design Standards are enforced according to the 'Enforcement Support for Green Building Construction'. The amount of electricity used to maintain room temperature at $28^{\circ}C$ in these buildings have a 30% reduction (measured on the walls and rooftop) in power usage compared to buildings not required to meet these standards. Although the effect of these energy savings on landscaping is proven, this demonstration is not effective for energy saving since it is not a suitable method for the 'Energy Saving Design Standards of Buildings'. For landscaping to be effective as far as a component of energy reduction, the perfusion rate of the building should be calculated based on the thermal conductivity of the component materials for the energy saving designs with respect to the basis of Article 14 of the Green Building Act. Therefore, the purpose of this study is to ensure that the planting-based mats currently being widely used in the landscape industry can have insulating performance suitable for the 'Energy Saving Design Standards' of Buildings according to the 'Enable Green Building Construction Methods'.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.3
• /
• pp.242-250
• /
• 2010

The aim of this study was to investigate the terpenoids of Total Volatile Organic Compounds (VOCs) released during drying of Cryptomeria japonica using the thermal extractor (TE). Considering the drying process of C. japonica, temperatures of TE were set at $27^{\circ}C$, $60^{\circ}C$, $80^{\circ}C$, $100^{\circ}C$, and $120^{\circ}C$, respectively. As the result, the emission factors of VOCs and terpenoids were increased as temperature increased. The amount of terpenoids included in VOCs emission factors were 87.5%, 81.6%, 83.6%, 90.1%, and 97.3% depending on above temperatures, respectively. Especially at$100^{\circ}C$ and $120^{\circ}C$, the amount of terpenoids were measured more than 90%. ${\delta}$-cadinene was the highest yield at each temperature and 32 types of terpenoids were collected. Emitted terpenoids were classified into the sesquiterpene group which consists of 15 carbon sources. These 32 sesquiterpenes were used for determining the useful bioactivity such as antifungal activity by the agar dilution. As the result, they showed the antifungal activity against Trichophyton rubrum, Trichophyton mentagrophytes, Microsporum gypseum. The 5,000 ppm concentration of terpenoids showed a strong activity with 100% against the 3 fungi. At the 1,000 ppm concentration of terpenoids, the antifungal activities against three fungi were 95.2%, 98.7%, and 97.3%, and their activities were a little inhibited at 100 ppm concentration.

• Journal of Korean Society of Forest Science
• /
• v.97 no.1
• /
• pp.35-44
• /
• 2008

Mycelial growth of Lentinula edodes on solid or liquid culture media supplemented with differentconcentrations of oak wood vinegar varied depending on the types of wood vinegar or mushroom varieties used.Oak wood vinegar obtained from traditionally carbonizing kiln (TWV) inhibited mycelial growth of L. edodes atthe dilution level of less than $5{\times}10^{-2}$, but stimulated at $10^{-3}$ to $2{\times}10^{-3}$. Wood vinegar from mechanicallycarbonizing kiln (MWV) inhibited at $10^{-3}$, but stimulated at $2{\times}10^{-3}$. In liquid culture media, both wood vinegarinhibited at $5{\times}10^{-2}$, but stimulated at $2{\times}10^{-3}$. Sanjo-302-ho grown in liquid culture media at $2{\times}10^{-3}$, and Sanrim 2and 3-ho grown at $4{\times}10^{-3}$ showed relatively high degree of wood decay (DWD) and growing ability within wood(GAWW) when these isolates were inoculated onto oak wood logs. TWV completely inhibited mycelial growth ofgreen mold fungi, Trichoderma species, tested at $5{\times}10^{-1}$ dilution level, while MWV inhibited at $5{\times}10^{-1}$ to $5{\times}10^{-2}$dilution level. For Diatrype stigma, TWV inhibited mycelial growth at the dilution level of less than $5{\times}10^{-2}$, whileMWV did 80% of mycelial growth at $10^{-2}$, and 100% at $5{\times}10^{-1}$ dilution level. Fresh and dry weight of fruitingbodies harvested after soaking of wood logs into wood vinegar solutions with different concentrations werecompared, and were the highest at $2.5{\times}10^{-2}$ dilution level. Storage test of fruiting bodies at $10^{\circ}C$ for 10 daysshowed that fruiting bodies harvested after soaking in the solution with $2.5{\times}10^{-2}$ dilution level showed the bestfreshness by general test and color changes. In addition, shear force value of L. edodes fruiting bodies measuredby using texture analyzer showed that $2.5{\times}10^{-2}$ dilution level was the best concentration for keeping flesh texture.

• Journal of the Korean Wood Science and Technology
• /
• v.12 no.2
• /
• pp.20-26
• /
• 1984

This study was carried out to investigate the influence of chemical type and its retention in the fire-retardant treated plywoods on the static bending strength, a property peculiar to plywood. Being soaked in 20% aqueous solution of $(NH_4)_2SO_4$, $NH_4H_2PO_4$, $(NH_4)_2HPO_4$. Borax-Boric acid and Minalith for 3 to 12 hours at three-hour intervals and redried at $120^{\circ}C$ in hot press, the treated plywoods were put to static bending test. The values of chemical treated plywoods in Stress at proportional limit, Modulus of elasticity, Modulus of rupture and Work per unit volume to proportional limit were widely higher than those of water treated plywoods(control) and Borax-Boric acid treatment showed the highest value in the four mechanical data. And the bending strength of fire-retardant treated plywoods increased with the extension of soaking time or the increase of chemical retention in themselves. Borix-Boric acid was the desirable fire-retardant for thin plywood in view of mechanical strength and soaking defects in this study.

• Journal of the Korean Wood Science and Technology
• /
• v.9 no.3
• /
• pp.7-15
• /
• 1981

A Japanese larch has been reforested very much in Korea, but it is not used as a wood resources for paper pulp by now. So this study is carried out to utilize the larchwood for paper pulp manufacture through the Asplund pulping process. The experiment on increasing in the brightness of the pulp is made through the addition of $MgSO_4$, $ZnSO_4$, $Al_2(SO_4)_3$, and KI as a cellulose stabilizer in chip treatment with caustic soda which is followed by high-temperature defibration and conventional peroxide bleaching (5% NaOH plus 2% additive salt per wood in cold pretreatment), or in high-consistency (30%) pulp bleaching of hydrogen peroxide and peracetic acid (100% acitve oxygen per lignin) for conventional one. The results obtained are as follows: 1. The solution of 0.5% additive salts had different pH by the sort of bases that was pH 5.7 in $MgSO_4$, liquor, pH 4.9 for $ZnSO_4$, and pH 2.9 for $Al_2(SO_4)_3$, and in the precepitation of bases which ranged to pH 6-13 for $MgSO_4$, pH 5-12 for $ZnSO_4$, and pH 3-10 for $Al_2(SO_4)_3$. 2. The cellulose stabilizer affective in high-consistency peroxide bleaching was KI, $MgSO_4$, and $ZnSO_4$, but has made a little improvement in de lignification and brightness of pulp in comparison with no addition. 3. The higher alkalinity in the chip treatment has made the higher strength and brightness of larchwood Aspiund pulp instead of downing the pulp yield. And the effective compound for cellulose stabilizer in caustic soda pretreatment of chip was $ZnSO_4$, $Al_2(SO_4)_3$ and KI in order for the conventional peroxide bleaching after Asplund pulping. 4. Therefore, the more effective additives for cellulose stabilization in high-temperature defibration of larchwood suppose to be $ZnSO_4$, $Al_2(SO_4)_3$, and KI, while KI and $MgSO_4$ for peroxide bleaching.

• Journal of the Korean Wood Science and Technology
• /
• v.28 no.2
• /
• pp.49-56
• /
• 2000

This study was designed to investigate the adsorption of heavy metal ions by untreated bark according to the treatment conditions of aqueous solution. The effect of temperature and pH of aqueous solution, particle size of bark, addition of light metal ions on the adsorption was examined, and the competition in adsorption among heavy metal ions was also evaluated. te The adsorption ratio of $Cu^{2+}$ and $Zn^{2+}$ increased with increasing themperature of solution from $-5^{\circ}C$ to $10^{\circ}C$ however, it was relatively constant at temperatures between $10^{\circ}C$ and $55^{\circ}C$. The adsorption ratio of $Cr^{6+}$ increased continuously with increasing the temperature of solution. The maximum adsorption ratio of $Cu^{2+}$, $Zn^{2+}$, and $Pb^{2+}$ was noted at pHs ranged 6 to 7; however, the adsorption ratio declined sharply on either sides of the optimum. The adsorption ratio of $Cr^{6+}$ decreased continuously with increasing the pH of solution. The adsorption ratio increased as decreasing the particle size of bark, and there was little differences in adsorption tendency between pine and oak bark. By the addition of $Ca^{2+}$ or $Mg^{2+}$(10~25 ppm), the adsorption ratio of $Cu^{2+}$ and $Zn^{2+}$ increased. An increase of the adsorption ratio was higher in oak bark than in pine bark. However, the adsorption ratio of $Pb^{2+}$ and $Cr^{6+}$ was not affected by the addition of light metal ions. As the mixed solution of 2 or 3 kinds of heavy metal ions($Cu^{2+}$, $Zn^{2+}$, $Pb^{2+}$) was treated with the untreated bark, the adsorption of $Zn^{2+}$ decreased considerably because of the competitive adsorption among heavy metal ions. Also the adsorption of $Cu^{2+}$ was more and less reduced. However the adsorption of $Pb^{2+}$ was not affected by the presence of other heavy metal ions.