• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.6
• /
• pp.821-826
• /
• 2013

When the values of design variables change, mode switching can often occur. If the mode of interest is not tracked, the frequencies and modes for design optimization may be miscalculated owing to modes that differ from the intended ones. Thus, mode tracking must be employed to identify the frequencies and modes of interest whenever the values of design variables change during optimization. Furthermore, reliability-based design optimization (RBDO) must be performed for design problems with design variables containing uncertainty. In this research, we perform RBDO considering the mode tracking of a compressive coil spring, i.e., a component of the joint spring that supports a compressor, with design variables containing uncertainty by using only kriging metamodels based on multiple responses approach (MRA) without existing mode tracking methods. The reliability analyses for RBDO are employed using kriging metamodel-based Monte Carlo simulation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.6 s.165
• /
• pp.1039-1047
• /
• 1999

It is necessary to evaluate the fatigue behavior of rail steel under the multi-axial stress state to assure the railway vehicle's safety. For this purpose, the stress analysis to investigate the crack initiation criteria, static failure and fatigue behavior under mixed-mode are performed. The stress analysis results show that the initiation of the transverse fissure depends on the maximum shear stress below the surface. For the mixed mode, the fatigue crack growth behavior which is represented by the projection crack length and comparative S.I.F, ${\Delta}K_v$, shows the more conservative results. Also, its rate is lower than that of the case of the mode I, and this difference decreases with increasing the stress ratio, R.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1508-1512
• /
• 2003

In this study, retardation behavior of fatigue crack under single overloading of the mixed mode state was experimentally investigated. To produce single overload in the mixed mode I+II state, the compact tension shear (CTS) specimen and loading device were used. The propagation tests for fatigue crack were performed under mode I and mixed-mode loading overloading afterwards. We examined the observed deformation aspects, the variation of fatigue life and crack propagation rate, and the aspects of retardation behavior from tests. The retardation effect of mixed-mode single overload on fatigue crack propagation behavior was smaller than that of mode I single overload. Also the loading modes of variable and constant amplitude loads have influence on the retardation behavior of fatigue cracks.

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.02a
• /
• pp.154-155
• /
• 2003

반도체 소자에 있어서 굴절율의 변화는 중요한 역할을 한다. 굴절율을 변화시키는 다양한 요소들은, 전계에 의한 1차 전기광학(linear electro-optic： LEO) 효과와 2차 전기광학 (quadratic electro-optic： QEO) 효과, 자유 운반자에 의한 밴드천이(band-gap shift： BS) 효과와 플라즈마(plasma： PL) 효과 등으로 잘 알려져 있다. 본 논문에서는, 오로지 TE 모드에 대해서만 선택적으로 위상 변화를 주는 P-I-i-I-N GaAs／Al／sub0.35／Ga／sub 0.65／As 도파로 위상변조기를 보고한다. (중략)

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.1
• /
• pp.22-32
• /
• 2008

This paper proposes a linearization technique for the 3-level NPC type inverter, which increases the linear control range of Inverter up to the one-pulse inverter. The overmodulation range is divided into two modes depending on the Modulation Index, MI. In overmodulation region I, the reference angles are derived from the fourier series expansion of the reference voltage corresponding to the MI. In overmodulation region II, the holding angles are also derived in the same way. Therefore, it is possible to obtain the linear control and the maximized utilization of PWM inverter output voltage.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.9
• /
• pp.1108-1119
• /
• 2016

This paper presents the spectral analysis and radiation pattern of low-frequency electromagnetic(EM) leakage signals according to the fundamental operations of smartphones. The EM leakage signals generated by the activation of four I/O sensor modules such as a touch-screen, a camera, a microphone and a speaker are captured by the commercial near-field magnetic probe with 1cm spatial resolution. The analysis results show that the leakage of the EM wave occurs strongly around the activated I/O sensor modules, AP(Application Processor) and memory modules. Also, the distinguishable frequency characteristic is shown in each spectrum of EM leakage signals.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.10 no.3
• /
• pp.74-78
• /
• 2011

In this paper, the bandpass filter for ITS system of 5.8 GHz is proposed by using the dual-mode resonator with the radial stub. As alternating the open stub with the radial stub, the size of the dual mode resonator can be reduced about 39.6% and the out-of-band characteristics of the bandpass filter using dual mode resonator can be enhanced from 19.4 dB to 29.1 dB by using the stub of $6.9{\Omega}$ i.e. realized by parallel two radial stubs with $60^{\circ}$ angle. The fabricated bnadpass filter using the dual mode resonator has the center frequency of 5.72 GHz with the fractional bandwidth of 4.1%. Also, the filter has the insertion loss and return loss of 1.79 dB and 19.4 dB, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.4
• /
• pp.535-541
• /
• 1998

A 2 stage 6-pole bandpass filter(BPF) is designed and implemented by using triple-mode cavity for satellite payload system. The BPF has an 100 MHz bandwidth at the center frequency of 14.5 GHz, Ku-band. The cavity filter uses two orthogonal $TE_{113}$ modes and one $TM_{012}$ mode. The intercavity coupling between the adjacent cavities results in a Chebyshev response and is accomplished by H-field component of TE modes. The size and location of intercavity slot are determined by the coupling equation from H-field of TE resonant modes in circular cavity. The measured filter response agrees well with the theoretical data.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.15 no.3
• /
• pp.389-398
• /
• 2002

The mixed mode problem (I and II) of a peny-shaped interface cracks in remote tension loading on a bi-material cylinder is studied using finite element method. The energy release rates for the tip of the crack in the interface were calibrated for several different moduli combinations and crack ratios using the modified crack closure integral technique and J-integral method, with numerical results obtained from a commercial finite element program. Numerical results show that non-dimensional value of$\sqrt{G_{II}E^*}/\sqrt[p]{\pi a}$ increases as the crack size or moduli ratio increases. Meanwhile, non-dimensional value of$\sqrt{G_{I}E^*}/\sqrt[p]{\pi a}$ decreases as the moduli ratio increases, but above the moduli ratio of 3 its value decreases then increases again as the crack size increases. Reliability of the numerical analysis in this study was acquired with comparison to an analytical solution for the peny-shaped interface crack in an infinite medium.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.11
• /
• pp.2072-2081
• /
• 1992

Theoretical fringe patterns were calculated and regenerated by using power series type Williams equations and coefficients estimated from the photoelastic data. Results of calculated values were evaluated by comparing experimental data points with the regenerated theoretical fringe loops. Statistical accuracy evaluation between regenerated fringe values and experimental ones showed that standard deviation was minimum and correlation coefficient was maximum when the first four terms of Wiliams equations were used.