• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.6
• /
• pp.586-595
• /
• 2010

An analytical study based on physical understandings and aero-thermodynamic theories was conducted to observe the performance characteristics and to derive the essential design parameters of dual ramjet(dual-combustion/dual-mode) propulsion for wide Mach number. The performances and operating limitations of the engines with two types combustors, such as constant pressure- and constant area- combustor, over various flight Mach numbers was investigated. Finally, the transition Mach number from ramjet to scramjet was carried out to optimize performance load balancing of ramjet and scramjet.

• Journal of KSNVE
• /
• v.8 no.6
• /
• pp.1062-1068
• /
• 1998

This paper describes the vibration characteristics of a high head pump-turbine runner. with nine blades and an outer diameter of 4.410 mm. of the pumped storage power plant. Mode shapes and natural frequencies were obtained by means of both the finite element analysis and modal testing. both in air and in water. The natural frequencies in air were calculated using the finite element method by ANSYS software. In order to confirm calculation results. the natural frequencies and mode shapes of the runner were measured using a hydraulic exciter both in air and in water. Natural frequencies of the pump-turbine runner were found at 174. 310 Hz in air, and at 107. 184 Hz in water. The first mode shape is flat plate mode with two nodal diameter and the second one is also flat plate mode with three nodal diameter. It can be shown that the natural frequencies of the pump-turbine runner in water is reduced approximately 40 ％ due to additional mass effect. Natural frequencies in air predicted by ANSYS software are in good agreement with test results.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.1 no.2
• /
• pp.36-43
• /
• 2010

In this study, the buckling loads and mode shapes characteristic of circular and non-circular(elliptical) closed composite shells were analyzed. To analyses the buckling behaviors, we develop and report an improved generalized shell element called 4EAS-FS through a combination of enhanced assumed strain and the substitute shear strain fields. A flat shell element has been developed by combining membrane element with drilling degree-of-freedom and a plate bending element. The combined influences of length, thicknesses, cross-sectional parameters, and fiber-angle on the critical buckling loads and mode shapes of circular and non-circular(elliptical) closed shells are examined.

• The KIPS Transactions:PartC
• /
• v.13C no.2 s.105
• /
• pp.177-184
• /
• 2006

A handover is a technology that enables data transmission and receipt seamlessly while a mobile station moves from the current base station to another base station. The handover is basically classified into two types; a horizontal handover which changes a radio link only without changing a network link, and a vertical handover which changes both in heterogeneous networks. In this paper, we propose a vertical handover protocol in a dual base station which supports both of W-CDMA and WiBro networks based on SDR (Software Defined Radio), verify the rightness using a state transition diagram and a Petri-net, and evaluate the performance of the proposed protocol using NS-2 simulator.

• Journal of Drive and Control
• /
• v.15 no.4
• /
• pp.48-54
• /
• 2018

The hydraulic servo actuator has always operated very precisely with high frequency and small displacement, and is used continuously for a long time. The hydraulic servo actuator of the test equipment used in the accelerated life test in order to guarantee the service life of the automotive parts failed earlier than the products before finishing the test. This study performed an analysis on the cause of the failure of the hydraulic servo actuator used in the test equipment, changed the design of the actuator to solve the root cause of the main failure mode, and developed the improved servo actuator. Based on above process, this study established a better performances and longer lifetime of the servo actuator after testing.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.15 no.2
• /
• pp.103-110
• /
• 2010

In this paper, a new mode changeable asymmetric full bridge dc/dc converter is proposed to solve the freewheeling current problem of the conventional zero voltage switching(ZVS) phase shift full bridge(PSFB) dc/dc converter of low output voltage and high output current applications. The proposed converter is operated as an asymmetric full bridge converter when the duty cycle is less than 50% and active clamp full bridge converter when the duty cycle is greater than 50%. As a result, since its freewheeling current is eliminated, the conduction loss is lower than that of the conventional ZVS PSFB dc/dc converter. Moreover, ZVS of all power switches can be ensured along a wide load ranges and output current ripple is very small. Therefore, high efficiency of the proposed converter can be achieved. Especially since its operation mode is changed to the active clamp full bridge converter during hold up time and can be operated with 50~100% duty ratio, it can produce the stable output voltage along wide input voltage range. The operational principles, theoretical analysis and design considerations are presented. To confirm the operation, validity and features of the proposed converter, experimental results from a 1.2kW($400V_{dc}/12V_{dc}$) prototype are presented.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.5
• /
• pp.400-408
• /
• 2007

In this paper, development of the 8kW parallel module converter is presented. For a effective configuration of FB-PWM converter, this paper proposes 4-parallel operation of 2 kw-module. FB converter of 2-kW module is controlled by phase shut PWM and in order to achieve ZVZCS, the simple auxiliary circuit is applied in secondary side. In order to achieve ZCS, control logic for auxiliary circuit operation is designed to reset the primary current during free-wheeling period. For output current sharing of 4-modules, the charge control is employed. The charge control logic is designed with phase shift PWM logic. Voltage controller is implemented by using DSP(TMS320LF2406) with A/D conversion data of the output current and voltage of each module. The developed converter is installed in PCU(Power Conditioning Unit) for HSG(High Speed Generator) in a vehicle and health monitoring system is implemented for vehicle operation test. Finally, performance of the developed converter is proved under practical operation of HSG.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.3 s.70
• /
• pp.295-303
• /
• 2004

In this paper, an improved four-node Reissner-Mindlin plate-bending element with enhanced assumed strain field is presented for the analysis of isotropic and laminated composite plates. To avoid the shear locking and spurious zero energy modes, the transverse shear behavior is improved by the addition of a new enhanced shear strain based on the incompatible displacement mode approach and bubble function. The "standard" enhanced strain fields (Andelfinger and Ramm, 1993) are also employed to improve the in-plane behaviors of the plate elements. The four-node quadrilateral element derived using the first-order shear deformation theory is designated as "14EASP". Several applications are investigated to assess the features and the performances of the proposed element. The results are compared with other finite element solutions and analytical solutions. Numerical examples show that the element is stable, invariant, passes the patch test, and yields good results especially in highly distorted regimes.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.850-851
• /
• 2011

본 논문은 SRM의 센서리스 속도제어를 위한 슬라이딩 모드 자속관측기법을 적용하고, 초기기동에서 센서리스 영역까지의 천이구간에서는 동일한 센서리스 추정방식과 계산된 자속의 오차 성분으로 오픈루프 상태에서 속도리플을 억제할 수 있는 방식과 전동기의 온도 및 파라미터 변화에 의한 자속 오차 성분으로 인해 발생하는 위치 추정오차를 보상하기 위한 새로운 추정위치 보상기를 제안한다. 제안된 추정위치 보상기는 SRM의 자기적인 특성에 의해 발생하는 인덕턴스 변곡점 위치를 실제 위치로 가정하여 추정된 센서리스 위치를 순시적으로 보상하는 방식이다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.04b
• /
• pp.218-222
• /
• 1993

A sliding mode controller associated with the moving sliding surface is formulate for the tip position control of a single-link flexible manipulator. After establishing the plant model which characterizes a noncollocated control system, a discontinuous control law is then constructed by restricting that velocity state variables are not available from direct sensor measurements. Using the proposed control law favorable system responses are accomplished through shortening the reaching phase without increasing maximum control torque. Furthermore, a low sensitiveness to extraneous disturbance is obtained. Computer simulations are undertaken in order to demonstrate these superior control performance characteristics to be accrued from the proposed methodology.