• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.2
• /
• pp.433-452
• /
• 2018

The shield tunneling method can minimize surface settlements by preventing the deformation of tunnel face and tunnel intrados due to tunnel excavation. For this purpose, it is very important to control the operating conditions of shield TBM. The face pressure and backfill pressure for tail void grouting should be the most important and immediate measure not only to restrain surface settlement, but also to influence the effective stress and pore water pressure around the circumstance of tunnel during excavation. The reaction of the ground to the application of face pressure and backfill pressure relies on the stiffness and permeability of ground. Especially, the reaction of saturated clayey ground formations, which shows the time-dependent deformation, is different from the permeable ground. Hence, in this paper it was investigated how the TBM operating conditions, ground stiffness, and permeability impact on the surface settlement of saturated clayey ground. For this purpose, a series of parametric studies were carried out by means of the stress-pore water pressure coupled FE analysis. The results show that the settlement of soft clayey ground is divided into the immediate settlement and consolidation settlement. Especially, the consolidation settlement depends on the ground stiffness and permeability. In addition, the existence of critical face pressure and backfill pressure was identified. The face pressure and backfill pressure above the critical value may cause an unexpected increase in the ground settlement.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.11
• /
• pp.1183-1189
• /
• 2015

This study focuses on the design of the tapered joints of a wind power turbine. The main variables of the tapered joint are the transmitted torque, shaft diameter, contact area of the tapered ring, and tightening torque of the bolts, which applies a compressive pressure from the hub to the shaft. The stress distribution of the taper fit was calculated under axisymmetric plane strain conditions because of the small taper angle. The axial displacement of the clamp can be calculated from the radial elastic deformation and the taper angle. The stress field of each ring is obtained from the cylinder stress equation. To verify the accuracy of the calculation, finite element (FE) analysis was performed, and the results of the calculation and FE analysis were compared. The hoop stress of the tapered surface showed a discrepancy of approximately 10, but the trends of the stress distributions of each component and the relative movement obtained by FE analysis were in good agreement with the analytical calculation results.

• Journal of the Korean Vacuum Society
• /
• v.15 no.5
• /
• pp.475-484
• /
• 2006

The deformation, the stress distribution, and the contact pressure of gaskets used in sealing flanges of CF (Con-Flat) or IPD (Improved) type were calculated to investigate the possibility of analyzing and estimatimg the sealing performance under a given tightening condition for a specific flange system.

• Tribology and Lubricants
• /
• v.36 no.1
• /
• pp.34-38
• /
• 2020

The powertrain of the waterjet system of a special-purpose vehicle makes use of the cardan shaft, which is composed of universal joints and shafts. These universal joints, composed of spiders and needle roller bearings, have to be designed with consideration for the bending and compressive stresses of the spiders and needle roller bearings, and the rating lives of the bearings. The bending and compressive stresses of the spider and bearing of a universal joint have been studied by many researchers. However, to design a universal joint effectively, overall consideration of the different specifications of needle roller bearings is necessary. In this study, the bending stresses of spiders and compressive stresses of needle roller bearings are calculated to design universal joints for powertrain cardan shafts with different roller diameters of bearing. Furthermore, the rating lives of the needle roller bearings are predicted using the calculated basic dynamic load ratings of the bearings. As a result, roller diameters less than 𝜙2.5 mm are found suitable through an analysis of the bending stress of the spider. All compressive stresses between spider and bearing, regardless of roller diameter, satisfy the requirements. Moreover, roller diameters of more than 𝜙2 mm are found suitable for the required rating life.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.6
• /
• pp.806-815
• /
• 2010

Gear trains are combined with the planetary gear units and helical gear units. It is known that the combination type is decisive to the system performances of the transmissions. In this paper, within the commonly used range of the design requirements for medium and large scaled (1~8 MW) wind turbines, the transmission characteristics of the typical layouts of the gear train are investigated. According to the international standard by ANSI/AGMA/AWEA 6006-A03, the gear boxes are basically designed and compared with respect to the system lifes of 99% reliability, total weight, the power densities, overall diameter/length and the maximum stresses of the gear teeth. With these comparison works, the characteristics of the layouts of gear trains are discussed.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.206-209
• /
• 2004

Mechanical behavior of a fuel stack was studied using an orthotropic material model. The fuel stack is essentially composed of a bipolar plate (BP), a gasket, an end plate, a membrane electrolyte assembly (MEA), and a gas diffusion layer (GDL). Each component is fastened with a suitable pressure. It is important to maintain a suitable contact pressure distribution of BP, because it influences the power efficiency of the fuel cell stack. When it is exposed to high temperature, its behavior must be stable. Hence, we performed stress analysis at high temperature as well as at room temperature. At high temperature, the contact pressure distribution becomes poor. Many patents have shown that using an elastomer can overcome this phenomena. Its effect was also studied. By using an elastomer, we found a good contact pressure distribution at high temperature as well as at room temperature.

• Journal of Drive and Control
• /
• v.13 no.4
• /
• pp.45-51
• /
• 2016

The power train of a hydro-mechanical, continuously variable transmission for forklifts makes use of hydro-static units, hydraulic multi-wet disc brakes & clutches, and complex helical & planetary gears. The complex helical & planetary gears are very important parts of the transmission because of a strength problem. In the present study, we calculated the specifications of the complex helical & planetary gear train, and analyzed the gear bending and compressive stresses of the gears. It is necessary to analyze the gear bending and compressive stresses thoroughly for optimal design of the complex helical & planetary gears with respect to cost and reliability. In this paper, we analyze the actual gear bending and compressive stresses of complex helical & planetary gears using the Lewes & Hertz equation, and we also verify the calculated specifications of the complex helical & planetary gears by evaluating the results of the data of allowable bending and compressive stress using the Stress vrs Number of Cycles curves of gears.

• Tribology and Lubricants
• /
• v.38 no.1
• /
• pp.22-26
• /
• 2022

A 1.7-ton grade small excavator is a construction equipment that can perform various functions in limited spaces where heavy equipment cannot enter easily. Owing to the recent acceleration of urbanization, it has been used increasingly in drainage and gas pipes, as well as for road repair works in urban areas. The power train of a traveling reducer for a 1.7-ton grade small excavator utilizes a complex planetary gear system. Complex planetary gears are vital to the power train of a traveling reducer as it mitigates the fatigue strength problem. In the present study, the specifications of a complex planetary gear train are calculated; furthermore, the gear bending and compressive stresses of the complex planetary gears are analyzed to achieve an optimal design of the latter in terms of cost and reliability. In this study, the actual gear bending and compressive stresses of a planetary gear system are analyzed using a self-developed gear design program based on the Lewes and Hertz equation. Subsequently, the calculated specifications of the complex planetary gears are verified by evaluating the results with the data of allowable bending and compressive stress based on curves of stress vs. number of cycles of the gears.

• Tribology and Lubricants
• /
• v.9 no.2
• /
• pp.1-8
• /
• 1993

기어가 비교적 큰 하중과 고속의 운전상태에서 사용되는 경우 되풀이 응력에 의한 피로를 대상으로 하는 면압이나 굽힘강도 이외에 치면에서 발생되는 긁힘이나 융착(瀜着) 또는 용착(溶着)을 대상으로 한 스코어링(scoring) 강도를 고려하여야 한다. 스코어링은 주로 치의 이끝 부분에서 접촉방향으로 긁힘이 나타나는 손상으로 특징지워진다. 미국기어제조협회(AGMA)에서는 윤활막 파손에 의한 금속과 금속과의 접촉에 기인하여 발생되는 여러형태의 손상, 예를 들면 scuffing, seizing, galling 등을 광범위하게 스코어링으로 통칭하고 있다. 미국계통의 기술분야에서는 스코어링을 고온 스코어링(hot scoring)과 저온 스코어링(cold scoring)으로 구분하고 있다. 고온 스코어링은 고속 운전시 표면의 섬광온도(flash temperature)에 기인한 용착과 접촉방향으로 재료를 이탈시키는 형태를 나타내고, 저온 스코어링은 저속의 기어에서 윤활막 파단으로 표면에 줄질(filing)한 듯한 손상이 발생되는 것을 나타낸다. 유럽에서는 고온 스코어링 손상은 스커핑이라 하고 저온 스코어링손상만을 스코어링이라 부르고 있다.

• Tribology and Lubricants
• /
• v.37 no.2
• /
• pp.48-53
• /
• 2021

Wind energy is considered as the most competitive energy source in terms of power generation cost and efficiency. The power train of the pitch drive for a wind turbine uses a 3-stage complex planetary gear system in being developed locally. A gear train of the pitch drive consists of an electric or hydraulic motor and a planetary decelerator, which optimizes the pitch angle of the blade for wind generators in response to the change in wind speed. However, it is prone to many problems, such as excessive repair costs in case of failure. Complex planetary gears are very important parts of a pitch drive system because of strength problem. When gears are designed for the power train of a pitch drive, it is necessary to analyze the fatigue strength of gears. While calculating the specifications of the complex planetary gears along with the bending and compressive stresses of the gears, it is necessary to analyze the fatigue strength of gears to obtain an optimal design of the complex planetary gears in terms of cost and reliability. In this study, the specifications of planetary gears are calculated using a self-developed gear design program. The actual gear bending and compressive stresses of the planetary gear system were analyzed using the Lewes and Hertz equation. Additionally, the calculated specifications of the complex planetary gears were verified by evaluating the results from the Stress - No. of cycles curves of gears.