• 한국신재생에너지학회:학술대회논문집
• /
• 2005.11a
• /
• pp.660-660
• /
• 2005

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.291-295
• /
• 2005

The PEMFC behavior is quite complex and is influenced by several factors, including composition and structure of electrodes and membrane type. Fabrication of MFA is important factor for proton exchange membrane fuel cell. MFA of PEMFC with hot pressing and direct coating method were prepared, and performances were evaluated and compared each other. The effect of MEA preparation methods, hot pressing methods and direct coating methods, on the cell performance was analyzed by impedance spectroscopy and SEM. The performance of PEMFC wi th direct coat ing method was better than wi th hot pressing method because membrane internal resistance and membrane-:-interfacial resistance were reduced by elimination of hot pressing process in MEA fabrication. In addition the micro structure of MEA with direct coating method reveals uniform interface between membrane and catalyst layer.

• Membrane Journal
• /
• v.27 no.3
• /
• pp.240-247
• /
• 2017

In this study, the heterogeneous ion exchange membranes prepared by the combination of the carbon electrode and mixed the cation and anion exchange polymers and polyvinylidene fluoride as the basic polymer together were made to recognize the efficiency of the salt removal for the application of the membrane capacitive deionization process. The mixing weight ratio of the solvent, basic polymer and ion exchange resin was 7 : 2 : 1 and this mixed solution was directly cast on the electrode. As for the operating conditions of the adsorption voltage and time, feed flow rate, desorption voltage and time of the feed solution NaCl 100 mg/L, the salt removal efficiencies (SRE) were measured. Apart from this NaCl, the $CaCl_2$ and $MgSO_4$ solutions were investigated in terms of SRE as well. Typically, SRE for NaCl 100 mg/L solution under the conditions of adsorption voltage/time, 1.5 V/3 min, desorption voltage/time -0.1 V/3 min, was shown 98%. And for the $CaCl_2$ and $MgSO_4$ solutions, the SREs of 70 and 59% were measured under the conditions of adsorption voltage/time, 1.2 V/3 min, desorption voltage/time -0.5 V/5 min, respectively.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.5
• /
• pp.8-14
• /
• 2007

In this paper, $HfO_2$/Hf stacked film has been applied as the gate dielectric in MOS devices. The $HfO_2$ thin film was deposited on p-type (100) silicon wafers by atomic layer deposition (ALD) using TEMAHf and $O_3$ as precursors. Prior to the deposition of the $HfO_2$ film, a thin Hf metal layer was deposited as an intermediate layer. Round-type MOS capacitors have been fabricated on Si substrates with 2000${\AA}$-thick Al or Pt top electrode. The prepared film showed the stoichiometric components. At the $HfO_2$/Si interface, both Hf-Si and Hf-Si-O bonds were observed, instead of Si-O bond. The sandwiched Hf metal layer suppressed the growing of $SiO_x$ layer so that $HfSi_xO_y$ layer was achieved. It seems that the intermediate Hf metal layer has a benefit for the enhancement of electric characteristics of gate dielectric in $HfO_2$/Si structure.

• Applied Chemistry for Engineering
• /
• v.21 no.1
• /
• pp.52-57
• /
• 2010

Although chemical sedimentation and ion exchange are usually applied to the treatment of heavy metal ions and radioactive cations, they have some serious disadvantages like a great consumption of chemicals, the disposal of valuable metals, and the secondary pollution of soil by the solid-waste. The advanced countries recently have studied the electrochemical ion exchange, combined electrochemical reduction and ion exchange, for the development of the alternative technique. This study has been performed to investigate the optimum condition for the preparation of the nickel hexacyanoferrate (NiHCNFe) which is an electrochemical ion exchanger. NiHCNFe film was deposited on the surface of nickel plate by chemical method or electrochemical method. The morphology and composition of NiHCNFe were observed by SEM and EDS, respectively. The peak current density of NiHCNFe was measured from the cyclic voltammograms of the continuous oxidation-reduction reaction in a parallel plane ion exchange electrode reactor. It was found that the chemical preparation method was better than the electrochemical method. The concentrated NiHCNFe was apparently deposited on nickel plate when dipping in the preparing solution for 118 h, especially. It also had a best durable performance as an ion exchange electrode.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.43-44
• /
• 2008

PECVD 방식에 의거 low-k 유전상수를 갖는 층간 절연막 (ILD)를 제작하였다. 전구체 BTMSM 액체를 기화하여 16sccm 에서부터 1 sccm씩 증가하면서 25sccm 까지 p-Si[100] 기판위에 유량비를 조절하였으며 60 sccm으로 일정산소 $O_2$ 가스를 반응 챔버에 도달하도록 하였다. 제작된 시편의 구성성분은 FTIR의 흡수선으로 확인하였고, 알루미늄 전극을 구현한 MIS (Al/SiOCH/p-si(100)) 구조의 커패시터를 가지고 정전용량-전압 (C-V) 특성을 측정하여 유전상수를 계산하였다. BTMSM/$O_2$에 의한 층간절연막의 k ~ 2 근방의 저유전상수는 유량비에 민감하게 의존되고 열처리에 의하여 $CH_3$의 소멸 및 Si-O-Si(C) 성장하는 효과에 의하여 더 낮아짐을 확인할 수 있었다. 또한 상온 및 대기압에서 공기 중에 노출시켜 자연 산화과정을 겪은 시편들의 유전상수는 전체적으로 증가하였지만, 열처리한 박막이 상대적으로 안정화된 것을 확인하였다.

• Applied Chemistry for Engineering
• /
• v.17 no.3
• /
• pp.243-249
• /
• 2006

Porous polymer gel electrolytes (PGEs) based on poly(vinylidenefluoride-co-hexafluoropropylene) (P(VdF-co-HFP)) as a polymer matrix and polyvinylpyrolidone (PVP) as a pore-forming agent were prepared and electrochemical properties were investigated for an electric double layer capacitor (EDLC) in order to increase a permeability of an electrolyte into the PGE. Propylene carbonate (PC) and ethylene carbonate (EC) as plasticizers, and tetraethylammonium tetrafluoroborate ($TEABF_4$) as a supporting salt for the PGE were used. EDLC unit cells were assembled with the PGE and electrode comprising BP-20 and MSP-20 as activated carbon powders, Super P as a conducting agent, and P(VdF-co-HFP)/PVP as a mixed binder. Ion conductivity of PGEs increased with an increased PVP content and was the best at 7 wt% PVP, whereas electrochemical characteristics such as AC-ESR of unit cell were better in 3 wt%. And electrochemical characteristics of the unit cell with PGE were the best at a 33 : 33 weight ratio of PC to EC. Specific capacitance of a mixed plasticizer system of PE and EC was higher than that of pure PC. Ion conductivity of PGEs with a film thickness of $20{\mu}m$ was higher, but electrochemical characteristics of unit cells were higher for a $50{\mu}m$ membrane thickness. Also, the unit cell has shown the highest capacitance of 31.41 F/g and more stable electrochemical performance when PGE and electrode were hot pressed. Consequently, the optimum composition ratio of PGE for EDLCs was 23 : 66 : 11 wt% such as P(VdF-co-HFP) : PVP = 20 : 3 wt% and PC : EC = 44 : 22 wt%. In this case, $3.17{\times}10^{-3}S/cm$ of ion conductivity was achieved at the $50{\mu}m$ thickness of PGE for EDLCs. And the electrochemical characteristics of unit cells were $2.69{\Omega}$ of DC-ESR, 28 F/g of specific capacitance, and 100% of coulombic efficiency.