• Journal of Korea Society of Industrial Information Systems
• /
• v.20 no.4
• /
• pp.67-73
• /
• 2015

Recently in the evaluation of physical properties of a material, its surface friction characteristics is much required. This study treats the development of portable and affordable friction coefficient tester, which includes utensil design and application, measurement circuit design and layout, and microprocessor based firmware building. Also, real applicability of the present portable friction coefficient tester has been shown via performance comparisons with the existing standard tester.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1413-1417
• /
• 2004

The environmental elements which naturally occur can result in structural damages and operating faults of vessels under the navigation and mooring. These primary factors are considered as wind, waves and tide. In order to investigate wind shielding effects with respect to wind load conditions between two ships which face the wind directly or slantingly to the wind direction, this numerical simulation was preferred in terms of the variation of wind loads according to different distances, wind velocities and wind directions between two ships. The results were proved to be quite reasonable, comparing with experimental data from Danish Maritime Institute, and the report, "Environmental Conditions And Environmental Loads" published by Det Norske Veritas.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.3
• /
• pp.171-181
• /
• 2017

Two-phase cross flow exists in many shell-and-tube heat exchangers such as condensers, evaporators, and nuclear steam generators. The drag force acting on a tube bundle subjected to air/water flow is evaluated experimentally. The cylinders subjected to two-phase flow are arranged in a normal square array. The ratio of pitch to diameter is 1.35, and the diameter of the cylinder is 18 mm. The drag force along the flow direction on the tube bundles is measured to calculate the drag coefficient and the two-phase damping ratio. The two-phase damping ratios, given by the analytical model for a homogeneous two-phase flow, are compared with experimental results. The correlation factor between the frictional pressure drop and the hydraulic drag coefficient is determined from the experimental results. The factor is used to calculate the drag force analytically. It is found that with an increase in the mass flux, the drag force, and the drag coefficients are close to the results given by the homogeneous model. The result shows that the damping ratio can be calculated using the homogeneous model for bubbly flow of sufficiently large mass flux.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.4
• /
• pp.658-666
• /
• 1992

In developing computer-aided design technology for optimization of stamping die design, it has been an important issue to treat the frictional constraint acting on the blank holder surface. The main goal of this work is to establish database of draw bead restraint force and clarify friction characteristic for various automotive sheet steels, which is essential in developing friction algorithm that can be used for CAD of stamping die design. Draw bead friction tester is used to evaluate the various parameters that affect the draw restraint force and the coefficient of friction for the cold rolled and the coated sheet steels such as drawing rate, lubricant type, surface property of material, etc.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.3
• /
• pp.177-182
• /
• 2007

The effects of three fuselage head shapes and nonplanar ground surface on the aerodynamic characteristics of FAST fuselages are investigated using a boundary element method. Wind tunnel test is also performed to validate the present method and to identify the wall effect on the frictional drag which cannot be analyzed using the present method. It is found that the channel has an effect of increasing the lift of those investigated fuselages. The optimal head shape depends on the design conditions of the FAST and its guideway channel. Comparing the calculated induced drag with the measured total drag, it can be concluded that the profile drag is independent of the ground height. Thus, the present numerical method can be applied to the conceptual design of the high-speed ground transporters if only the profile drag of the vehicle in free flight is assumed to be known.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1994.10a
• /
• pp.265-270
• /
• 1994

본 연구에서는 케비테이션 터널에서의 경사진 원형실린더의 유동유기진동시험을 통하여 경사각에 따른 유동유기진동 특성규명과 아울러 유체력 계수들의 실험적 산정을 시도하였으며 도출된 주요한 결론은 다음과 같다. 경사각이 20.deg. 이상되면 마찰저항력에 비해 수직항력이 지배적이 되며, 이때 수직항력계수는 여러 관찰자에 의해 관측된 범위의 값(1.7-2.0)을 갖는다. 또한, 양력계수 $C_{L,rms}$은 유속범위 4$_{n}$D<8의 범위에서 lock-in 현상에 의해 큰 값을 갖게 되며, 경사각이 커질수록 큰 값을 갖는다. 경사각이 30.deg.인 경우 최대값은 약 0.9, 20.deg.인 경우 0.4로 계측되었다.

• Journal of the Korea Concrete Institute
• /
• v.27 no.3
• /
• pp.299-309
• /
• 2015

Ultra High Performance Fiber Reinforced Concrete (UHPFRC) is distinguished from the normal concrete by outstanding compressive and tensile strength. Cracked normal concrete resists shear by aggregate interlocking while clamped by transverse reinforcement, which is called as shear friction theory. Cracked UHPFRC is expected to have a different shear transfer mechanism due to rather smooth crack face and post-cracking behavior under tensile force. Twenty-four push-off specimens with transverse reinforcement are tested for four different fiber volume ratio and three different ratio of reinforcement along the shear plane. The shear friction strength for monolithic concrete are suggested by limit analysis of plasticity and verified by test results. Plastic analysis gives a conservative, but reasonable estimate. The suggested shear friction factor and effectiveness factor of UHPFRC can be applied for interface shear transfer design of high-strength concrete and fiber reinforced concrete with post-cracking tensile strength.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.30 no.3
• /
• pp.209-219
• /
• 1994

The practical application of riblet to three dimensional double model, for viscous drag reduction, was studied analytically by intergal solution to three dimensional turbulent boundary layers. The case of a V-groove riblet technique on the shear stress and boundary layer velocities were incooperated in the computation of the flow over a smooth slender ship hull. As the results the possible mechanism of turbulent drag reduction by riblets are then suggested based on detailed studies of near-wall turbulence characteristics. And a turbulent boundary layer calculation scheme based on a momentum integral method was modified for the computer program. An example of the calculation results is presented.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.1
• /
• pp.9-18
• /
• 2013

Two-phase vapor-liquid flows exist in many shell and tube heat exchangers such as condensers, evaporators, and nuclear steam generators. To understand the fluid dynamic forces acting on a structure subjected to a two-phase flow, it is essential to obtain detailed information about the characteristics of a two-phase flow. The characteristics of a two-phase flow and the flow parameters were introduced, and then, an experiment was performed to evaluate the pressure loss in the tube bundles and the fluid-dynamic force acting on the cylinder owing to the pressure distribution. A two-phase flow was pre-mixed at the entrance of the test section, and the experiments were undertaken using a normal triangular array of cylinders subjected to a two-phase cross-flow. The pressure loss along the flow direction in the tube bundles was measured to calculate the two-phase friction multiplier, and the multiplier was compared with the analytical value. Furthermore, the circular distributions of the pressure on the cylinders were measured. Based on the distribution and the fundamental theory of two-phase flow, the effects of the void fraction and mass flux per unit area on the pressure coefficient and the drag coefficient were evaluated. The drag coefficient was calculated by integrating the measured pressure on the tube by a numerical method. It was found that for low mass fluxes, the measured two-phase friction multipliers agree well with the analytical results, and good agreement for the effect of the void fraction on the drag coefficients, as calculated by the measured pressure distributions, is shown qualitatively, as compared to the existing experimental results.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.21 no.3
• /
• pp.216-223
• /
• 2009

A transverse drag interaction coefficient of the equivalent resistance coefficient formula for square multi-piers higher than water depth and arranged with equal intervals was studied. From the assumption that the energy loss due to drag interaction according to transverse intervals of resistance bodies is essentially identical to the energy loss due to thick orifice according to porosities, the transverse drag interaction coefficient was derived by employing the orifice's energy loss coefficient. The equivalent resistance coefficient formula including the drag interaction coefficient was compared with the numerical experiments using FLOW-3D, the performance of which was verified by Kim et al.(2008) in the experimental condition with the multi-piers. The comparisons showed good agreement and thus, the equivalent resistance coefficient formula, which does not only consider frictional resistance but also consider the multi-piers' drag resistance varied according to the intervals in longitudinal or transverse direction, was verified.