• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.614-614
• /
• 2012

개수로에서 혹은 수리구조물 주변에서의 흐름 및 난류 특성을 파악하기 위해서는 연직유속분포 및 수심별 평면유속분포의 측정이 필요하다. 유속분포를 측정하기 위한 방법은 음파 도플러 유속계(ADV:Acoustic Doppler Velocimetry)를 사용하는 방법과 PIV 기법을 이용하는 방법이 있다. 일반적으로 ADV는 한 지점의 유속을 시간변화에 따라 연속적으로 측정할 수 있어 난류특성의 정량적인 해석에 장점이 있으나 동시간에 여러 지점을 측정할 수 없기 때문에 난류의 공간적인 문제를 해석함에 있어서 한계가 있다. 그러나, 입자영상유속계(PIV:Particle Image Velocity)는 측정하고자 하는 단면에서 연직 횡단면의 유속분포 및 수심별 평면 유속분포 흐름장 측정이 가능하여 난류흐름의 공간적인 문제를 해석하는데 효과적일 뿐만 아니라 영상간의 시간간격을 짧게 하고, 촬영시간을 충분히 길게 한다면 개수로 내 난류특성 분석도 가능하다. 이에 본 연구의 목적은 PIV 기법을 이용하여 매끄러운 하상의 개수로에서 연직유속분포를 측정하고 그 특성을 정량적으로 분석하고자 한다. 본 연구에서는 첫째, PIV 기법을 이용하여 측정한 연직유속분포와 3차원 전자식 유속계를 이용하여 측정한 연직유속분포를 비교 분석하였다. 둘째, 후류법칙에 의해 계산된 연직유속분포와 PIV 기법을 이용하여 측정한 연직유속분포의 비교를 위해 각각의 무차원 유속분포(지점 유속/지점 마찰속도)를 계산하고 비교하였다. 마지막으로 각 흐름 조건에 따라 수심의 변화를 주어 연직유속분포를 PIV 기법으로 측정한 후 개수로의 수심변화에 따른 연직유속의 특성을 분석하였다. 분석 결과, PIV 기법을 이용하여 측정한 연직유속 성분에 비해 3차원 전자식 유속계로 측정한 연직유속 성분이 작게 나타났고 바닥에서부터 0.2h 지점까지는 무차원 유속분포(지점 유속/지점 마찰속도)가 후류법칙과 잘 맞는 경향을 보였으나 0.2h 지점부터 수표면까지는 유속이 감소하는 현상이 나타났다.

• The Journal of Engineering Geology
• /
• v.27 no.1
• /
• pp.91-101
• /
• 2017

Fault materials has various properties depending on their areas, rock types, and components because they are formed by heterogeneous and complicated mechanisms. In this study, to understand the physical and mechanical properties of fault materials, 109 fault materials distributed in South Korea were collected to conduct various laboratory tests with them and analyze their physical and mechanical properties (unit weight, specific gravity, porosity, gravel content, silt/clay content, clay mineral content, friction angle, and cohesion) according to areas, rock types, and components. As for the physical and mechanical properties by rock type, gneiss shows the highest medians in the unit weight ($17.1kN/m^3$) and specific gravity (2.73), granite does so in the porosity (45.5%), schist does so in the gravel content (20.0 wt.%) and cohesion (38.1 kPa), and phyllite does so in the silt/clay content (54.4 wt.%), clay mineral content (30.1 wt.%), and friction angle ($38.2^{\circ}$). With regard to the physical and mechanical properties by component, fault gouge was shown to have lower values than cataclasite and damage zones in all factors other than porosity and silt/clay contents.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.1
• /
• pp.140-152
• /
• 1997

A simultaneous measurement of the wall skin friction and near-wall streamwise velocity fluctuations is performed using hot film and hot wire anemometers to investigate the relation between them. Near-wall turbulence statistics measured with a hot-wire probe are in good agreement with previous results. Turbulence properties of the wall skin friction fluctuations measured with a hot film also show fairly good agreements with those measured by others except that rms level is lower in the present study. Long-time averaged space- time correlations show that the wall skin friction is highly correlated with a turbulence structure which is tilted from the wall in the streamwise direction. Tilting angles are obtained from the phase shifts between the wall skin-friction and streamwise velocity fluctuations. The convection velocity of the near-wall streamwise velocity obtained from the space-time correlation is in good agreement with that from the direct numerical simulation database.

• Tunnel and Underground Space
• /
• v.28 no.6
• /
• pp.584-595
• /
• 2018

This study conducted direct shear test on about 290 sorts of materials such as sandy soil, clayey soil and gravely soil to present proper standard on shear strength of soil. Shear strength of soil in large scale tends to show that angle of internal friction increases as sand contents grow and it ranges $23.5^{\circ}{\sim}34.9^{\circ}C$ with cohesion of 2.0 kPa~15.7 kPa. Elastic modulus was visibly distinct by load, and which increased approximately 80% as vertical load grows. Angle of internal friction arranging $15.0^{\circ}{\sim}28.6^{\circ}$ on clayey soil decreased as clay contents rises and cohesion increase in regular scale. Elastic modulus tends to increase initial elastic modulus with almost same growing rate. While angle of internal friction on gravely soil indicates $29.9^{\circ}{\sim}36.7^{\circ}$ which hardly shows distinctive features. According to test in detail, cohesion of SW (well-graded sand), SP (poorly-graded sand), SC (clayey sand) and SM (silty sand) indicates value by 94%, 78% and 59% comparing to SC, SW and SP respectively. Angle of internal friction of ML (low-liquid limit silt) and CL (low-liquid limit clay) appears almost same features, and MH (high-liquid limit silt) despite of 88% value of ML. Cohesion among them varies with similar growing rate.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.03a
• /
• pp.66-66
• /
• 2011

우리나라 근해의 풍부한 해양자원인 해조류를 염재로 한 천연염료의 제조는 자원의 부가가치를 높일 뿐만 아니라 새로운 색소성분의 발굴과 함께 천연염색의 색상 다양화 효과를 얻을 수 있다. 본 연구는 국내 자생 해조류로부터 다양한 색상을 얻기 위해 여러 가지 추출공정을 사용하여 색소를 추출하고 염색성을 조사하여 새로운 염재로서의 유효성을 확인하는데 목적이 있다. 이를 위하여 사용한 해조류는 제주에서 자생하는 구멍갈파래, 청각이다. 해조류 색소를 추출하여 분말화 형태로 만들어 염색하였고 추출공정에 따른 다양한 색상 구현을 할 수 있게 되었다. 해조류 색소의 특성을 알아보기 위해 UV-Vis, FT-IR 분석에 의해 그 성분을 확인하였다. 염색은 면섬유, 견섬유, 모섬유, 나일론섬유를 사용하여 염색하였다. 추출공정의 다양화를 통해 해조류 색소를 직물에 염색했을 때 직물의 색상과 염착량에 미치는 영향을 평가하였고, 세탁, 마찰 그리고 일광에 대한 견뢰도를 측정하였다. 색소의 기능성을 평가하기 위해 해조류 색소분말의 황색포도상구균(Staphylococcus aureus)에 대한 항균성을 평가하였다. 본 연구에서 추출공정을 달리하여 제조한 해조류 색소는 다양한 색상구현에 적합하였고, 견직물과 모직물에 염착이 잘 되었다. 또한 해조류 색소는 항균성을 지녀 향후 기능성 천연염료로서 응용가능성이 매우 클 것으로 전망된다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1994.10a
• /
• pp.73-79
• /
• 1994

(1) 진공청소기의 소음은 팬모타의 회전에 기인하는 유체소음과 진동소음이 주류를 이루며, 여기에 공기의 흡입과 배출에 따른 유체소음등이 복합되어 나타난다. (2) 진공청소기의 소음특성은 각 소음원들의 특성에 따라 주파수대역을 구분할 수 있으며, 기계적 진동음인 500Hz부근에서 peak를 보인다. (3) 소음의 저감을 위하여는 기존에 정립되어 있는 흡음, 차음, 감쇠, 방진, 유압유속감소 등의 기술을 종합적으로 활용하여 제한된 공간내에서 효과를 극대화할 수 있는 구조개발이 필요하며 본 연구에 적용하였다. (4) 본 연구의 '정음유로구조'는 차음효과, 유로길이 증가에 의한 감쇠효과, 흡음효과를 극대화할 수 있는 구조이다. (5) 팬모타의 진동모드는 회전축을 중심으로 원운동을 하며, 진동량은 흡입구와 뒷쪽 베어링부위가 가장 작으므로 회전축에 가까운 곳을 지지하는 것이 방진에 유리하다. (6) 본 구조에서 사용된 케이싱은 484Hz의 고유진동수 성분을 가지며 이는 모타와 공진할 우려가 있다. 이에 공진주파수 성분의 진동량이 가장 작은 전면과 후면의 중앙부를 지지하여 진동을 줄일 수 있었다. (7) 본체소음의 전반적인 저감에 따라 흡입구 등에서 발생하는 공기마찰소음의 영향이 상대적으로 커지며, 따라서 흡입구의 유선형 설계 및 누설소음의 흡음, 차폐 등의 역할이 중요한 관리 요소로 된다.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.19 no.2
• /
• pp.125-129
• /
• 1983

It is customary to assume that the resistance of a jull at uniform speed may be regarded as the sum of viscous and wavemaking component resistance, or C sub(i)=C sub(v)+C sub(w), where C sub(v) is regarded as a function of Reynolds Number R and C sub(w) a function of Froude Number F. Formulae have been obtained for ∂C sub(w)/∂R, ∂C sub(v)/∂F which may be relevant in seeking theoretical grounds for possible interaction between viscous and wavemaking component resistances. The values of ∂C sub(w)/∂R are small. In general they are smaller than corresponding values of ∂C sub(v)/∂R. But although these values are small it does not follow that they are entirely negligible. The Froude assumption that the rate of change of C sub(w) with R is zero must bel regarded as incorrect.

• Journal of the Korean Geotechnical Society
• /
• v.35 no.10
• /
• pp.47-66
• /
• 2019

A parametric numerical analysis according to diameter, length, and N values of soil was conducted for the PHC pile socketed into weathered rock through sandy soil layers. In the numerical analysis, the Mohr-Coulomb model was applied to PHC pile and soils, and the contacted phases among the pile-soil-cement paste were modeled as interfaces with a virtual thickness. The parametric numerical analyses for 10 kinds of pile diameters were executed to obtain the load-settlement relationship and the axial load distribution according to N-values. The load-settlement curves were obtained for each load such as total load, total skin friction, skin friction of the sandy soil layer, skin friction of the weathered rock layer and end bearing resistance of the weathered rock. As a result of analysis of various load levels from the load-settlement curves, the settlements corresponding to the inflection point of each curve were appeared as about 5~7% of each pile diameter and were estimated conservatively as 5% of each pile diameter. The load at the inflection point was defined as the mobilized bearing capacity ($Q_m$) and it was used in analyses of pile bearing capacity. And SRF was appeared above average 70%, irrespective of diameter, embedment length of pile and N value of sandy soil layer. Also, skin frictional resistance of sandy soil layers was evaluated above average 80% of total skin frictional resistance. These results can be used in calculating the bearing capacity of prebored PHC pile, and also be utilized in developing the bearing capacity prediction method and chart for the prebored PHC pile socketed into weathered rock through sandy soil layers.

• Journal of the Korean Geosynthetics Society
• /
• v.15 no.3
• /
• pp.67-76
• /
• 2016

The railway bridge abutment subjected to the lateral earth pressure is a sensitive structure that is affected by backfill materials, installation methods, compaction, and drainage system and so on. The several design loads for the bridge abutment design consist of traffic loading on bridges and vertical & lateral force due to surcharge load at backfill. Especially, the lateral earth pressure of design load components is important and considered in the design of geotechnical engineering structure such as bridge abutment wall. The determination of cross section for abutment is finally determined with calculating external stability and member force of abutment wall structures. In this study, the abutment wall height is 12m and the optimal cross section of abutment wall has been determined that satisfies an external stability for abutment structure through friction angles of 35, 40, and 45 degrees of backfill materials. The external stability and member force of abutment wall with friction angle of backfill materials and were calculated and construction cost of each abutment wall structures was compared. It found that the construction cost was reduced from 2.2 to 8.4% with friction angle of backfill materials.

• Journal of the Korean Geotechnical Society
• /
• v.35 no.11
• /
• pp.75-95
• /
• 2019

The numerical analysis on PHC piles socketed into weathered rocks through sandy soil layers was conducted to propose the table solution or the chart solution to obtain the mobilization capacity. The mobilization capacity was determined at the settlement of 5% pile diameter and applied a safety factor of 3.0. In order to utilize the excellent compressive strength of the PHC pile effectively, it is recommended that the allowable bearing capacity of ground would be designed to be more than the long-term allowable compressive pile load. A procedure for determining an allowable pile capacity for PHC piles socketed into weathered rocks through sandy soil layers is given by the sum of the allowable skin friction of the sandy soil layer and the weathered rock layer and the allowable end bearing capacity of the weathered rock layer. The design efficiency of the PHC pile is about 85% at the reasonable design stage in the verification of the newly proposed method. Thus, long-term allowable compressive load (P_all) level of PHC piles can be utilized in the optimal design stage.