• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.3
• /
• pp.212-218
• /
• 2020

When Radiofrequency energy is applied to the human body, the vibration width is very short. Therefore, the electrolyte burn generated when using the direct current does not occur. Ion molecules, polarized molecules, etc., vibrate more than 40,000 times per second, converting them into frictional heat to generate deep heat. The blood flow of capillaries increases 4-5 times more than at rest, increasing the supply of oxygen, nutrients, antibodies, and white blood cells. In addition, the electrochemical reaction does not occur because the vibration width and the pulsation period are very short. It is a physical factor treatment method that does not stimulate the sensory nerves and motor nerves. In this study, an isotonic exercise is performed in a young normal adult using a Radiofrequency pain treatment device. The purpose of this study is to integrate rehabilitation therapy by measuring electromyography data during isotonic exercise and confirming the effect on changes in motor neuron response. The EMG data generated when isotonic exercise of the forearm biceps muscle and the EMG data measured after the use of a Radiofrequency pain treatment device after exercise were RMS, respectively, and verified through t-test. It was confirmed that there was a significant difference in both men and women because the t-value was smaller than the significance level p (<.05).

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.2
• /
• pp.183-190
• /
• 2016

Engine torque is transferred to the transmission where drag torque is minimized improving fuel efficiency. This is particularly true in a wet clutch pack. This study measures slip friction when the wet clutch pack in a DCT (Dual-Clutch Transmission) is disengaged, and the friction pads are slipping. Shudder engagement velocity, and applied forces can be measured under various working conditions through these torque transfer experiments. Test results demonstrate that the design parameters, and engagement conditions of wet clutch packs can be optimized to reduce shudder and frictional vibration during engagement in a dual clutch transmission.

• Journal of the Korea Convergence Society
• /
• v.8 no.10
• /
• pp.193-199
• /
• 2017

Mechanical tappet is used to reduce the cost and friction loss compared with hydraulic tappet. But the mechanical tappet doesn't have the ability to control the clearance between cams and valves and is selected by measuring the distance between valves and cams in order to minimize the clearance of valves by considering thermal expansion of valves. So, the valve clearance is nearly zero after fully warming-up periods, but there is valve clearance before warming-up. Especially at cold condition, the clearance is relatively large and can bring about some problems. In this study, the valve motions like lift, velocity, seating velocity and bouncing height were studied at various valve clearance conditions by experiment and analysis. As the valve clearance increases, the ramp area becomes shorten and it causes the valve train motion to have bad effects.

• Journal of Aerospace System Engineering
• /
• v.9 no.4
• /
• pp.23-30
• /
• 2015

The focal plane image stabilization for a camera is one of the most effective method that can increases the digital camera's image quality by compensating the vibration disturbance. The optical image stabilization can be implemented by making the focal plane to trace the path of incident light. To control the position of focal plane motion compensating stage precisely, a nonlinear control algorithm has been applied by considering coulomb friction which is nonlinear behavior of the compensator system. In our study, we have analyzed the hand shaking vibration using the gyro sensor, and made a mathematical model of compensating stage containing optical sensor and piezo-actuator. Then the nonlinear control algorithm has been designed and its performance has been verified by experiment. In this study, a friction driven peizo-electric actuator with $1{\mu}m$ resolution and 10mm/s speed has been used for stage movement.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.49 no.4
• /
• pp.69-77
• /
• 2012

We propose a PLL-type position control method for step motors. Our control method considerably improves the instability problem at rapid acceleration or deceleration, which is a major problem of conventional open loop control methods. Moreover, our controller reduces the steady state position error to zero and guarantees lower vibration and acoustic noise at high speed. Also, our controller can produce more torque at high speed, and hence it can extend the controllable velocity range. To demonstrate the practical significance of our control method, we present some simulation results for a commercially available step motor using Simulink.

• Journal of Korean Ophthalmic Optics Society
• /
• v.13 no.1
• /
• pp.5-13
• /
• 2008

Purpose: This review article was written to investigate what kind of forces are acting on the contact lens fitted on the cornea and its subsequent motion. Methods: A capillary action-induced force develops in the tear layer between the lens and cornea, which leads to the restoring force due to difference in layer thickness according to lens rotation. The characteristics of the lens movement can be determined by the various factors such as friction between eyelid and lens, acceleration force based on blinking and the restoring force incorporated with the viscous damping force. A mathematical model which consists of the differential equations and their numerical solution was proposed to analyze the damped motion of lenses. The model predicts the time dependence of lenses during and after the blink varying the BC, blink period and eyelid pressure. Results: It was found that both the blink period and lid pressure increases the movement increases because of the enhanced lid friction. As the BC increases the viscous damping reduces due to the lacrimal layer's increase which resulted in the enhanced lens motion. After blink the lens illustrates the damped oscillation because of the restoring force by the increased lacrimal layer thickness and reduced viscous resistance. The time for the lens to return to the equilibrium shortens as the BC increase because of the resistance reduction. Conclusions: The movement of the contact lens is governed by the characteristics of the lacrimal layer between the lens and cornea as well as the lid blink.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.5
• /
• pp.673-678
• /
• 2013

Creep groan noise occurs at low frequencies immediately after releasing brake pressure or when a car stops. This noise can be used to predict problems in not only the brake system but also the vehicle system. Because of its complexity, it is difficult to determine its characteristics. Therefore, most improvements are conducted by changing the brake pad, and it still remains difficult to conduct a test using a vehicle. In this study, the characteristics of creep groan noise and the effects from a vehicle system are investigated by using vehicles and an NVH chassis-dynamometer through various tests. A new evaluation method for creep groan noise by using a vehicle is proposed, and the possibility of reduction schemes from the viewpoint of the vehicle system is confirmed from the results mentioned above.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.5
• /
• pp.609-616
• /
• 2019

When the fouling of a vessel occurs, its resistance at sea increases and there is a corresponding increase in fuel consumption. The maintenance cost of the vessel also increases because it is time-consuming to remove the fouling. To solve this problem and minimize environmental contamination of sea-water, there have been recent developments in anti-fouling paints as self-polishing copolymers that not include toxic elements such as tin. When these conventional techniques are applied to vessels, polishing is promoted during the operation whereby friction or vibration with seawater occurs. This leads to enhanced anti-fouling performance. However, when fouling is intensified such as during an anchorage, there is no flow of seawater and polishing is suppressed. This leads to a deterioration of the performance of anti-fouling. To solve these problems, we developed a system that induces vibration in a vessel during anchorage. As such, the deterioration of polishing due to insuf icient flow of seawater is inhibited. The reliability of the ultrasonic antifouling system was evaluated by calculating its repeatability. The removal efficiency of fouling of the proposed system was qualitatively evaluated using test specimens. The test revealed that the value of the coefficient of variation for the reproducibility of the frequency and amplitude was 0.2 % and 4.0 % on average. The degree of fouling of the specimens was the highest at 73.3 g in the No.5 sepcimen. Moreover, efficiency of fouling removal was 93.2 % on average compared to the specimens without the proposed system.

• Applied Chemistry for Engineering
• /
• v.7 no.6
• /
• pp.1027-1033
• /
• 1996

Under the Irradiation of the radiofrequency wave, the dipole materials vibrate as microwavic phase change. This causes friction between adjacent molecules and enables an unique charateristics of interior heating of the materials. When dipole gases are adsorbed inside of a solid radiofrequency wave absorber, the gases can be decomposed easily by the microwave energy. The decomposition of sour gases was successfully tested in this manner to develop a sour gas removal process from the combustion flue gas. The standard gas bearing NO and $SO_2$ was passed through and microwave was applied on the calcined char bed as the wave absorber and the gas adsorbent. It was found that more then 95% of NO and 70 % of $SO_2$ was decomposed to the environmentally clean elements during the passage through the 20 gram char bed under the microwave impingement. The surface area and the porosity of char increased because the oxygen radicals produced from decomposed gas attacked carbon in the char capillaries and formed $CO_2$. For a lower concentration of sour gas, general cases in the commercial combustion processes, almost complete decomposion is believed possible and this method is surely expected to be useful for the prevention of air pollutions.

• Journal of Aerospace System Engineering
• /
• v.17 no.6
• /
• pp.27-34
• /
• 2023

This paper presents the application of a magnetic gear to the electric propulsion system for an aircraft. Since high torque is required in aircraft electric propulsion systems, combining a speed reducer can amplify the torque. However, mechanical gears have issues, such as friction, vibration, and heat generation, which lead to maintenance challenges. In the case of a direct-drive motor that does not use mechanical gears, the size and weight of the motor increase to achieve high torque. This paper proposes the application of a magnetic gear to solve the maintenance issues of mechanical gears and the weight increase problem of direct-drive motors in aircraft electric propulsion systems. In this paper, a magnetic gear suitable for aircraft electric propulsion systems is designed, and it is compared with a direct-drive motor in terms of performance and the feasibility of applying the magnetic gear is verified.