• Proceedings of the KWS Conference
• /
• 2004.05a
• /
• pp.165-167
• /
• 2004

마찰교반접합(FSW, Friction Stir Welding)은 영국 TWI에 의해 1991년에 개발되어 특허가 출원된 후 90년대 중반부터 산업에 적용되었으며, 짧은 시간동안에 실용화가 이루어졌다. 이 기술이 적용되기 전, Al 합금의 접합은 MIG(Metal Inert Gas)나 TIG(Tungsgten Inert Gas)와 같은 접합이 주로 이용되어 왔으나, 이들 접합기술은 접합부의 표면문제, 변형, 결함 등으로 인하여 Al 합금의 구조물 적용에 큰 문제점이 야기되어왔다. (중략)

• Proceedings of the KWS Conference
• /
• 1995.04a
• /
• pp.114-117
• /
• 1995

A study of friction welding of high speed steel(SKH51) bar for blade side to carbon steel(STC3) bar for shank side was carried out experimentally through tensile test, hardness lest, microstructure, and acoustic emission (AR) test. So, this paper deals with optimizing the welding conditions and the real-time quality(strength) evaluation of friction welded joints by acoustic emission technique.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.2
• /
• pp.135-143
• /
• 2013

Friction Stir Welding (FSW) was developed, it is successfully commercialized in the field of transportation vehicles. In this study, we analyzed the defects of A2024-T4 alloy using non-destructive test of radiograph, ultrasonic, electrical conductivity and destructive test of microstructure observation, tensile strength. As the results of experiment, mapping of defects was obtained. Fine defects which were not detected in radiograph test were detected in ultrasonic test, and it enabled efficient detection of defects by difference of sound pressure and color. The values of electrical conductivity was decreased as amount of defects was increasing. Joint efficient of defect-free weldment that found by non-destructive and destructive test was 91%. Therefore it was considered that non-destructive test of friction stir welded A2024-T4 Alloy was an efficient method.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.3
• /
• pp.109-116
• /
• 2007

The present study examined mechanical properties according to the change of outer circumference in the friction welding of A2024-T4 stock, which is used much as aircraft structure, truck wheel, stainless materials and A2024-T4 stock with 10 hollow at the center. Welding conditions were fixed at RPM 2,000rpm, friction pressure of 50MPa, friction time of 1.5sec, upset pressure of 120MPa and upset time of 2.0 seconds. From the result of this study were drawn conclusions as follows : According to the result of a tensile strength test, the solid shaft showed linear increase of tensile strength with the change of outer circumference, the hollow shaft showed maximum tensile stength when the length (L) was 2mm and decrease of tensile strength with the change of outer circumference, hardness appeared to increase and then decrease for welding interface, and it showed maximum hardness 155Hv at L=5mm of the solid shaft. Bending strength increased linearly far change of the distance (L) of outer circumference in the solid shaft and then decreased linearly in the hollow shaft. the result of examining tissue, the tissue grew finer around the welding interface and divided the basic material and the welding surface.

• Journal of Ocean Engineering and Technology
• /
• v.11 no.1
• /
• pp.10-15
• /
• 1997

Copper and its alloy had been used widely because of its pronouncing characteristics on their high thermal and electrical conductivity. Various fusion welding methods, such as SMAW, SAW, GTAW, GMAW, Electroslag welding amd so on are applied to weld copper and its alloy. But fusion welding of copper has so many welding problems. THe most serious problems were poor penetration amd high thermal contration stress due to its high thermal conductivity and porosity could be formed by rapid cooling rate of fusion welding. In order to avoid such fusion welding problems, preheating, peering and heat treatment must be applied to obtain sound weld joint of copper. But preheating induce another welding problem such as grain coarsening of weld heat affected zone. This grain coarsening reduces ductility and strength of weld joint. In this view of point, friction welding of copper is triedm to obtain sound weld joint of copper by reducing metallurgical problems. This study introduced new concept of heat input for evaluating the friction weldability of copper. As a result, weldability of copper could be evaluated by this new concept of heat input.

• Proceedings of the KWS Conference
• /
• 1993.05a
• /
• pp.27-30
• /
• 1993

• Proceedings of the KWS Conference
• /
• 1997.05a
• /
• pp.204-210
• /
• 1997

• Proceedings of the KWS Conference
• /
• v.43
• /
• pp.103-105
• /
• 2004

• Proceedings of the KWS Conference
• /
• 2000.10a
• /
• pp.235-237
• /
• 2000

• Proceedings of the KWS Conference
• /
• 2000.10a
• /
• pp.314-316
• /
• 2000