• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.4
• /
• pp.19-29
• /
• 1995

This paper discusses the stick-slip phenomenon of the driveline system of a vehicle in consideration of friction. Friction is operated on the between of flywheel and clutch disk. The expressions for obtaining the results have been derived from the equation of motion of a three degree of freedom frictional torsion vibration system which is made up driving part(engine, flywheel), driven part(clutch, transmission) and dynamic load part(vehicle body) by applying forth-order Rungekutta method. It was found that the great affect parameters of the stick-slip or stick motion were surface pressure force between flywheel and clutch disk, time decay parameter of surface pressure force and 1st torsional spring constant of clutch disk when driveline system had been affected by friction force. The results of this study can be used as basic design data of the clutch system for the ride quality improvement of a car.

• Journal of Power System Engineering
• /
• v.15 no.3
• /
• pp.31-37
• /
• 2011

직조 금속 스크린 리브(rib) 이 바닥에 설치된 사각 덕트에서 열전달과 유체유동의 압력강하를 측정하기 위해 실험적 연구를 수행하였다. 시험부의 치수는 200 mm(W) ${\times}$ 40 mm(H) ${\times}$ 712 mm(L)이고 수력직경은 66.6 mm이다. 입구영역에는 1.72m 길이의 가열되지 않은 동일한 치수의 채널을 설치하였다. 메쉬가 다른 4가지의 직조금속 스크린 리브에 대해 측정하였다. 그리고 비교를 위해 일체형 리브에 대해서도 측정하였다. 국부 열전달 계수의 측정에는 스테인레스 강제 포일(foil) 히터와 T형 열전대률 이용하였다. 레이놀즈 수는 23,000에서 58,000의 범위이다. 덕트의 수력직경($D_h$)에 대한 직조 금속 리브의 높이(e)의 비($e/D_h$)는 0.075 이고 리브 간격(p)과 높이의 비(p/e)는 10이다. 실험 결과 메쉬가 없는 일체형 리입에서 가장 누셀트 수와 마찰계수가 컷다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.21 no.2
• /
• pp.126-135
• /
• 1997

Drag reduction in polymer solutions is the phenomenon where by extremely dilute solutions of high molecular weight polymers exhibit frictional resistance to flow much lower than the pure solvent. This effect, largely unexplained as yet, has attracted the attention of polymer scientists and fluid flow specialists. Although applications are beginning to appear, the principle interest to data has been in attempting to relate the effect to the fluid mechanics of turbulent flow. Drag reduction in two phase flow can be applied to the transport of crude oil, phase change system such as chemical reactor, and pool and boiling flow. But the research on drag reduction in two phase flow is not intensively investigated. Therefore, experimental investigations have been carried out to analyze the drag reduction produced by polymer addition in the single phase and two phase flow system. The objectives of the proposed investigation are primarily in identifying and developing high performance polymer additives for fluid transportations with the benefits of turbulent drag. Also we want to is to evaluate the drag reduction in horizontal flow by measuring pressure drop and mean velocity. Experimental results show higher drag reduction using co - polymer(A611P) then using polyacrylamide (PAAM) and faster degradation using PAAM than using A611P under the same superficial velocity.

• Journal of the Society of Naval Architects of Korea
• /
• v.33 no.1
• /
• pp.54-64
• /
• 1996

It seems that blowing air bubble out of the bulb surface of a ship of flat bottom will reduce the frictional resistance, since wetted area of the hull surface is reduced owing to air bubble staying close to the surface. To as certain this concept, at first, the limiting streamlines around the bow was observed, and local distribution of pressure and shear stress, due to the change of air-blowing position, air supply pressure, and the model speed, was investigated. It was found that the local friction was reduced near the bulb and air-bubble formations also play an important role as a drag component. This paper can be considered as a preliminary study on the drag reduction of conventional ships by the micro-bubble injection.

• Journal of the Korean Society for Railway
• /
• v.16 no.4
• /
• pp.253-261
• /
• 2013

According to the measured results of KTX brake squeal noise in this study, high level brake noise occurred in a wide frequency range, 100~18,000Hz. To identify the sources of the brake squeal noise, unstable vibration modes due to brake disc/pad interaction were analyzed under various conditions by the finite element method. Complex eigenvalues for a brake unit with a disc and four pads were obtained. It was found that the real parts of the complex eigenvalues, that is, unstable vibration modes, were closely related to friction coefficients, pressure on the brake cylinders, elastic moduli of the components, and other conditions.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.181-186
• /
• 2002

Lately, as going on increasing in the demand of high power density(power/weight), it is necessary for hydraulic axial piston pump/motor to operate more high pressure and speed. But in these condition, there are some trouble like as friction loss. To reduce this friction loss, hydrostatic bearing is used far axial piston pump/motor frequently. In general, it is difficult to measure accurate friction torque of spherical hydrostatic bearing in the use of the existing devices. So, we have developed the measurement device using the reaction torque sensor to obtain the pure friction torque, fitted in the casing. In this report, we intend to make an introduction about this measurement device for friction torque of the spherical wear part and clarify the effect of friction characteristics on supply pressure and rotational speed with three types of pocket size by using this measurement device.

• Journal of Ocean Engineering and Technology
• /
• v.1 no.1
• /
• pp.138-143
• /
• 1987

Friction welding has emerged as a reliable process for high-production commercial applications with significant economic and technical advantages. But nondestructive test in friction weld was not clearly developed. Therefore the experimental verification is necessary in order to understand the characteristcs of the pulse echo effects according to various change in welding conditions. This paper presents an attempt to determine the relationship between the varios welding conditions and the coefficients of reflection using the ultrasonic pulse echo method in dissibilar metals friction weld. The new approach of calculating the coefficients of reflection based on measured amplitudes of the echoes is applied in this paper. These coefficients provides a single quantitative measurement which involves both acoustic energy reflected at the welded interface as well as transmitted across the interface. As a result, it was known that the quantitave relationship between welding conditions and the coefficients of reflection using the ultrasonic pulse echo exists in dissimilar metals friction weld.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.6
• /
• pp.207-213
• /
• 1999

In this study, the possibility of estimation of friction coefficient between tire and road surface using running car data are checked. To get necessary data, such as tire and car velocities and braking force, a test car is driven with certain magnitude of decelerations from pre-set initial velocities to stop . The data are used to estimate friction coefficient with property chosen parameters , e.g,, driving stiffness, pressure distribution functions, etc. Experimental results show that running data car be used with properly chosen parameters to estimate friction coefficient.

• Nuclear Engineering and Technology
• /
• v.25 no.2
• /
• pp.233-236
• /
• 1993

For one-dimensional two-phase flow without phase change and without axially-temporally rapid change of pressure, the interrelationship between the drift-flux model and the two-fluid model is studied. It is derived on the basis of the fact that the vapor conservation equation is related to the momentum equation by the drift flux. Starting from the two-fluid model, we obtain the interfacial friction expressed in terms of drift-flux parameter. Also, by deriving the void propagation equation, the drift-flux is shown to have jnterrelationship with forces in the two-fluid model.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.6
• /
• pp.1282-1291
• /
• 1989

본 연구에서는 이러한 연구의 시작단계로 노즐내의 열 경계층 방정식을 정리하고 압축성 와점도모델을 도입하여 유한 차분법을 이용한 전산프로그램을 작성 하였다. 한편 실제로 추진모테에서는 고온 고속의 열기류가 분출되기 때문에 추진 하고 있는 동안 노즐벽을 형성하고 있는 내열재가 심하게 손상되어 표면의 상태가 매우 거칠게 된다. 더구나 경우에 따라서는 내열재가 용발(ablation)하게 된다. 이러한 상태를 감안하여 마찰계수와 열전달 계수를 합리적으로 추정해야만 노즐의 설계와 주변장치를 합리적으로 수행할 수 있다. 따라서 본 연구에는 주로 경계층 내의 압력구배, 압축성의 효과, 물성치의 변화를 고려한 기존 난류모델에 근거하여 프로그램을 작성하고, 이것을 토대로 노즐표면 조도의 영향 및 분출(blowing)의 영 향을 중점적으로 고려하여 그 특성을 연구하였다. 노즐벽에서 분출을 고려한 이유는 표면이 용발할 때 표면의 온도가 거의 일정하게 유지된 상태로 노즐표면이 화학작용을 수반하면서 가스화됨을 초보적으로 고려해보기 위함이다.