• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제28회 추계학술대회
• /
• pp.17-24
• /
• 1998

Plasma-sprayed coatings were obtained by spray-dried $Cr_2O_3$ powder with and without Mo addition. A reciprocal type tribo-tester was employed to examine friction and wear behavior of the specimens at room temperature. The composition and the worn surface of coated specimens were observed by XRD and SEM. The results showed that friction Coefficient of the Mo added specimens were lower than one of $Cr_2O_3$ specimen. But $Cr_2O_3$ specimen had a lower wear loss. Protecting layer were observed at the worn surface of coated specimens with Mo addition.

• Tribology and Lubricants
• /
• 제17권3호
• /
• pp.221-227
• /
• 2001

The effect of silver particles on the sliding behavior of bearing steels was studied experimentally by using a ball-on-disk tribometer. Tests were performed in ambient air, dry air and vacuum. Disks of AISI 52100 were silver-coated by a thermal evaporation method, and the effects of silver particle transfer on friction were analyzed. In order to understand further the mechanism of silver particle transfer and its effect on friction and wear, pre-compressed silver particles were artificially introduced into the friction interface and the results were compared to those of silver-coated specimens. Results showed that the introduced silver particles produced transfer layers and resulted in low friction. It also showed that this low friction is closely related to the characteristic behavior of transfer layers. Shakedown occurred at the friction interface affected the friction and wear.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1996년도 제23회 학술대회
• /
• pp.83-86
• /
• 1996

In this study, CrN, TiN and TiN + CrN coatings have treated onto the steel substrates by ion plating to improve their tribological behaviors. Some of the specimens were ion nitriding treated to study the effect of ion nitriding on wear behavior. The wear tests were performed with these specimens by ball-onplate type and disc-on-plate type wear tester. It was demonstrated that ion nitriding treatment improve wear resistance of the coatings. The results of high temperature wear tests indicated that the specimens coated with CrN were exhibited the better wear resistance properties than the specimens with TiN coatings

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제28회 추계학술대회
• /
• pp.265-271
• /
• 1998

High temperature wear behavior of plasma sprayed zirconia based coating sealing with zirconia sol were investigated for high temperature wear resistance application. The zirconia powders containing 2.5, 5.0, 7.5, 10.0 mol% of MoS$_2$, $Fe_2O_3$ for plasma spray were made by spray drying method. As-sprayed coating was sealed by zirconia-sol to fill up the pore and crack in coating. wear test were performed at temperature ranges from room temperature to 600$\circ$C. The microstructural changes of before and after sealing process were examined by SEM, XRD and EPMA. After sealing process, the porosity was decreased and micro-hardness was increased. The wear properties of coating after sealing process were improved by sealing of pores and cracks. The behavior of wear amount and coefficient of friction were same tendency to before sealing process.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 제5회 압출 및 인발가공 심포지엄
• /
• pp.7-14
• /
• 2002

To carry out the analysis of the extruding products, it is necessary to get the optimum computation of extruding force for the extrusion. The existing numerical models of the extrusion may be large different from the actual conditions. In this study, accurate theoretical analysis of the extrusion forming and optimum extruding force should be subjected. It is to develop the numerical models which describes the optimum extrusion force. Therefore, the results should improve accuracy of extrusion forming and cause the energy saving for the extrusion.

• 한국세라믹학회지
• /
• 제31권5호
• /
• pp.520-528
• /
• 1994

An investigation was carried out to understand the effect of the amount of free silicon on the tribological properties of Si-SiC. The specimens of dense Si-SiC composites with various amount of free silicon were fabricated in the temperature of 175$0^{\circ}C$ after molding under various pressure. Wear properties were measured by ball-on-plate wear tester under the constant weight of 4 Kgf at constant sliding speed of 500 mm/sec in water. As the result, the Rockwell hardness and fracture strength of Si-SiC composites remained nearly constant up to 16.62 vol% of free silicon in the Si-SiC microstructure. The Si-SiC composites containing the free silicon of 16.62 vol% was considered to be prominent in the tribological properties, which had the friction coefficient of 0.08 and the specific wear rate of 2.4$\times$10-8$\textrm{mm}^2$Kgf-1. The analysis of the wear surface indicated the complicated processes occuring on the surface such as fine polishing, abrasion, microfracture.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2015년도 제46회 하계학술대회
• /
• pp.760-761
• /
• 2015

기어는 회전 기계 사이의 동력 전달을 위한 장치이며 현재 산업 전반의 통상적인 기어는 기계적 기어가 주류로서 형성되어 있다. 하지만 기계적 기어는 맞물린 톱니바퀴의 물리적 접촉에 의해 접촉 경계면의 마모 및 파손, 소음과 진동의 문제가 있으며 유지보수 비용 또한 크다. 따라서 최근 물리적 접촉이 없어 기계적 기어의 많은 문제를 해결할 수 있는 마그네틱 기어 (Magnetic Gear)에 대한 관심이 높아지고 있다. 마그네틱 기어는 영구자석에서 생성된 자계를 이용하여 비접촉 동력전달이 가능하며, 마찰손실 제거, 유지보수의 용이성, 매우 적은 소음 및 진동 등의 장점을 가지고 있다. 본 논문에서는 이러한 마그네틱 기어의 토크전달 방법과 형상변화에 따른 전달토크 특성을 2-D 유한요소해석법을 이용하여 해석하고 분석하고자 한다.

• 한국생산제조학회지
• /
• 제20권6호
• /
• pp.692-696
• /
• 2011

A clutch is a very important component when engine starts and gear shifting is needed. The clutch the most commonly used is the dry clutch. This type of clutch has pads, and they are worn after disengagement of clutch little by little. The characteristics of the clutch changes as these pads wear, so wear needs to be measured, and the clutch should be controlled for proper operation. In this study, the clutch contact point estimation algorithm has been developed. From this algorithm, clutch force map changes depending on wear, and the clutch operates properly. We also see the shifting transient of a vehicle for drivability with throttle valve position control and synchronizer movement.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.187.1-187.1
• /
• 2014

아연 가격의 상승과 경량합금개발의 중요성이 부각됨에 따라 아연을 대체할 새로운 강판용 내식소재의 개발이 중요하다. Al-Mg 합금 박막은 낮은 밀도를 가지면서 질량 대비 높은 강도, 좋은 내식성을 지녀 아연도금강판을 대체할 코팅소재로 그 가능성이 연구되고 있다. 이러한 Al-Mg 합금 박막의 실용화를 위해 국내외의 관련 연구그룹에서 연구를 진행하고 있으며, 그 결과 Al-Mg 합금 박막의 내식성 및 기계적 특성은 박막의 조성 및 미세구조와 상당한 관련성이 있음이 알려지고 있다. 본 연구에서는 sputtering법으로 냉연 강판에 Al-Mg 합금을 조성 및 열처리 여부 등을 조절하여 증착시킨 후 각 조건에 따른 박막의 미세구조와 기계적 특징을 조사하였다. 각 조건별 내마모도와 경도, 마찰계수, 밀착력을 분석하여 기계적 특성과 미세구조와의 상관관계를 도출하고자 하였다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2009년도 춘계학술대회 논문집
• /
• pp.269-270
• /
• 2009

본 연구는 윤활첨가제에 의한 반도체재료 가공용 다이아몬드 마이크로 블레이드의 절삭성능 향상과 수면연장을 위한 기술개발을 목표로 한다. 마이크로 블레이드와 피 절삭재 사이의 마찰특성의 향상, 그로인한 절삭성능의 향상 등에 미치는 윤활제의 종류와 그 효과를 규명하기 위하여 Cu/Sn계열 다이아몬드 마이크로 블레이드용 결합제에 흑연과 $MoS_2$를 통일한 부피분율로 첨가한 시편을 만들고, 기계적 특성평가와 순간전력소모로 평가하는 절삭성능시험, 블레이드의 마모량 측정을 통한 내구성 실험을 행하였다. 그 결과 기계적 특성과 밀접한 내마모성에 기인한 수명의 관점에서 $MoS_2$를 첨가한 경우가 흑연을 첨가한 경우보다 더 효과적으로 나타났다. 절삭할 때 필요한 순간전력소모로 평가한 절삭성능 평가에서는 동일한 부피분율의 윤활제가 첨가된 경우 차이는 비교적 미미하였다.