• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.876-881
• /
• 2001

DLC(Diamond-like carbon) films possess high hardness, low friction coefficient, and good wear resistance. Due to these properties, DLC films have been used extensively in magnetic hard disk industry. The objective of the present study was to investigate the influence of environmental condition on the tribological behavior of DLC coated hard disk. It is found that the tribological characteristics of DLC films are strongly affected by relative humidity and temperature. Specifically, the friction coefficient increases with increase in temperature at relative humidity of 50%. However, at 20% and 85% RH the effect of temperature was not significant. Also, the degree of wear could be observed using an AFM.

• Tribology and Lubricants
• /
• v.20 no.6
• /
• pp.299-305
• /
• 2004

The wear properties of clutch facing materials with two different copper amounts were evaluated against the fly-wheel materials used in clutch system, such as gray cast iron and spheroidal graphite cast iron. Sliding wear tests were carried out for four different combinations with these clutch facing materials and flywheel materials at different speeds and applied loads. Results showed that the clutch facing material contained a higher copper amount had the better wear resistance. And using the gray cast iron as the counter material, clutch facing material resulted in the much lower wear rate, regardless of the copper amount. It is obvious that the wear properties of clutch facing material are influenced from the thermal conductivities of the clutch facing material and the counter material.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.772-779
• /
• 2000

The friction and wear behavior of short carbon fiber reinforced polyetheretherketone was studied experimentally under dry sliding conditions against SCM440(AISI 4140) disks with a different surface roughness and hardness at the low sliding speeds and the high pressures on a pin-on-disk apparatus. Under the low disk surface roughness value the earsplitting noise and stick-slip were occurred. The increased adhesion friction and wear factor with stick-slip made the friction and wear behavior worse. Under the high disk surface hardness the break and falling-off of carbon fibers were accelerated. The carbon fibers fallen off from the matrix were ground into powder between two wear surfaces and this phenomenon caused a abrasive friction and wear factor to increase. So the friction and wear behavior became worse. With the transfer film made of wear particles formed on a disk, the carbon powder film formed on a pin lowered a friction coefficient.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.766-771
• /
• 2000

This study is mainly concerned with friction and wear properties for the piston ring of non-lubricating air compressor which made of PTFE-polyimide composites. At the PTFE and polyimide alone mixture specimens, PTFE80%-polyimide20%, which shows the lowest men friction coefficient and specific wear rate at 0.94m/s sliding speed. At each of carbon, copper and oxide lopper mixed with PTFE80%-polyimide20%. In case of copper10%, at 0.94m/s sliding speed, the mean friction coefficient shows 0.087, which is the lowest value in all specimens. In case of the specific wear rate, copper30% specimen shows the lowest value of $2.537E-5(mm^3/Nm)$ in all specimens.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.4
• /
• pp.122-128
• /
• 2009

The purpose of this study is to show the friction and wear characteristics on the vapor deposited coating layers on the SCM415 steel. In this research, frictional wear characteristic of coating materials such as CrN, AlCrN, WC/C was investigated under room temperature, normal air pressure and nothing lubricating condition. Therefore this study carried out research on the friction coefficient, micro hardness(Hv), roughness, EPMA on the vapor deposited coating layers on the SCM415 steel.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.1 no.2
• /
• pp.89-102
• /
• 1993

In this experimental investigation, various plasma-sprayed zirconia contained coatings and a kind of alumina-zirconia coating were studied to gain a better understanding of their tribological behaviour under dry contact condition in a reciprocating motion at temperature of 200℃. Particular attention was made for finding appropriate coatings in cylinder liner/piston ring application with an emphasis on the antiwear property. In order to identify the wear mechanism, SEM(Scanning Electron Microscope), optical micrograph, and roughness tester were used. Alumina-zirconia and 8% yttria-zirconia were found to be most appropriate for the application to the cylinder liner/piston ring and, especially, alumina-zirconia exhibited highest wear-resistance and also showed good friction characteristics. Wear mechanisms of ceramic coatings identified.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.1
• /
• pp.55-62
• /
• 2016

Nuclear fuels are always exposed to hot temperature and high speed coolant flow during the reactor operation. Thus the fuel rod accompanies small amplitude vibration due to the turbulent flow. The random vibration causes friction between the fuel rod and the grid structure which provides the lateral supports. The friction is critical to the fuel rod fretting wear, and it degrades fuel performance when a severe wear is developed. LuGre friction model is introduced in the paper, and the performance was evaluated comparing to the classical Coulomb model. It is shown that the developed friction force considering the Coulomb friction is not enough to stop or delay the motion while the stick-slip can be simulated using LuGre friction model. Numerical solutions of the two dimensional spacer grid cell model with the modern friction are also reviewed, and it is discussed that the new friction model simulates well the nonlinear mechanism.

• Tribology and Lubricants
• /
• v.25 no.4
• /
• pp.243-249
• /
• 2009

A magnetic clutch consists of pulley and disk. It delivers and isolates the power needed for the operation of the compressor used in automotive air conditioning system. To improve the performance, efficiency and durability of automotive air conditioning system, appropriate design of pulley, disk and system working parameters(the magnitude of magnetic force, and so on) is necessary. For that goal, it is required to understand the friction characteristics of magnetic clutch for the initial operating time. In this study, friction tests were carried out in order to investigate the effect of sliding velocity on the friction characteristics of magnetic clutch using pin-on-disk type friction and wear tester. For experiments, pulley and disk used in real automotive air conditioning system were considered. Friction experiments were conducted under various sliding velocities, and coefficients of kinetic friction were obtained. Under the experimental conditions considered in this study, the coefficients of kinetic friction increased with the increase of test number(sliding distance) and decreased with the increase of sliding velocity.

• Tribology and Lubricants
• /
• v.26 no.3
• /
• pp.162-166
• /
• 2010

The purpose of this study is to show the friction and wear characteristics on the vapor deposited Tiseries coating layers on the SCM415 steel. In this research, frictional wear characteristic of coating materials such as TiN, TiCN, TiAlN was investigated under room temperature, normal air pressure and dry lubricating condition. Therefore this study carried out research on the friction coefficient, micro hardness(Hv), roughness, SEM on the vapor deposited coating layers on the SCM415 steel.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.126-126
• /
• 2000

다이아몬드상 카본(DLC) 필름은 경도가 높고, 마찰계수가 낮다는 장점을 가지고 있기 때문에 내마모성 코팅이나 윤활성코팅에 응용을 위한 연구가 활발히 진행중이다. 하지만 마찰계수가 주변환경에 매우 큰 영향을 받는다는 단점이 있다. 이러한 단점은 DLC필름의 응용에 대한 저해 요인이 되며, 이 점을 보완하기 위해서 DLC 필름에 Si을 첨가하는 연구들이 진행되고 있다. 본 실험에서는 r.f-PACVD 법을 이용하여 Si이 첨가된 DLC 필름의 주위 환경 변화에 따른 마찰특성의 변화를 연구하였다. 사용한 반응 가스는 벤젠(C6H)과 희석된 Silane(SiH4 : H2 = 10 : 90)이며, 희석된 Silane과 벤젠의 첨가비율을 조절하여 필름내 Si의 함량을 조절하였고, 증착시 바이아스의 전압은 -400V로 하였다. 마찰테스트는 Ball-on-Disk type의 조건에서 대기, 건조공기, 진공의 세가지 분위기에서 마찰테스트를 실행하였다. 실험결과 마찰계수는 건조공기, 대기, 진공의 순으로 증가하였고, 필름내에 포함되어 있는 Si의 양이 증가할수록 마찰계수는 낮고 안정한 값을 나타내었다. Tribochemiacal 분석과, ball과 track의 전자현미경 사진 분석 결과, 진공에 비해서 건조공기와 대기중에서 마찰계수가 낮은 것은 DLC 필름내에 마모 track 중심부에 Si-C-O 계의 화합물이 형성되어, 이 화합물이 마찰계면에 존재하여 마찰계수를 낮추었음을 확인하였다. 그리고 대기중에서 실험한 경우, 습기의 존재로 인해 마모입자가 볼의 표면에서 엉김으로써 건조공기의 상태에서 보다 높은 마찰저항을 갖게 됨으로 인하여 마찰계수가 높아짐을 알 수 있었다.a)는 as-deposit 상태이며, 그림 1(b)는 45$0^{\circ}C$, 60min 열처리한 plan-view TEM 사진이다.dical의 영향을 조사하였으며 oxygen radical의 rf power에 따른 변화는 OES(Optical emission spectroscopy)를 사용하였다. 너무 적은 oxygen ion beam flux나 oxygen radical은 film의 전도도 및 투과도를 저하시켰고 반면 너무 과도한 flux의 증가 시는 전도도는 감소하였고 투과도는 증가하는 경향을 보였다. 기판에 도달하는 oxygen ion flux는 faraday cup을 이용하여 측정하였으며 증착된 ITO film은 XPS, UV-spectrometer, 4-point probe를 이용하여 분석하였다. 때문으로 생각되어진다. 또한, 성장 온도가 낮아짐에 따라 AlGaN의 성장을 저해하기 때문으로 판단된다. 성장 온도 변화에 따라 성장된 V의 구조적 특성 및 표면 거칠기 변화를 관찰하여 AlGaN의 성장 거동을 논의하겠다.034, 0.005 정도로 다시 감소하였다. 박막의 유전율은 약 35 정도의 값을 나타내었으며 X-선 회절 data로부터 분석한 박막의 변형은 증온도에 따라 7.2%에서 0.04%로 감소하였고 이 이경향은 유전손실은 감소경향과 일치하였다.는 현저하게 향상되었다. 그 원인은 SB power의 인가에 의해 활성화된 precursor 분자들이 큰 에너지를 가지고 기판에 유입되어 치밀한 박막이 형성되었기 때문으로 사료된다.을수 있었다.보았다.다.다양한 기능을 가진 신소재 제조에 있다. 또한 경제적인 측면에서도 고부가 가치의 제품