• Journal of Adhesion and Interface
• /
• v.6 no.1
• /
• pp.11-18
• /
• 2005

The capsules were prepared from a phase change material (PCM) of octadecane as a core material and melamine formaldehyde resin as a shell material. The PCM capsule size was varied in the range of $3{\sim}25{\mu}m$. The core contents and sizes of the PCM capsule, were determined by DSC and SEM, respectively. An acrylic coating material which contains butyl acrylate (BA), methyl metacrylate (MMA) and acrylic acid (AA) were synthesized by emulsion polymerization. The films were prepared from the acrylic emulsion and PCM capsules which have various capsule sizes. From the results of SEM experiment, it was observed that the PCM capsules were well dispersed inside the film and the surface of the film became less rough when the PCM capsule size was small. The swelling ratio of the films were not significantly affected by the PCM capsule size. However, the tensile strength and elongation of the films were greatly decreased with increasing the PCM capsule size.

• Applied Chemistry for Engineering
• /
• v.31 no.6
• /
• pp.635-638
• /
• 2020

We prepared spherical silica by minimizing the amount of oil through water/oil (W/O) emulsion. The spherical silica was successfully synthesized by using 20 to 60 mL of hexane as an oil for 283 g of water glass. The size of silica was dependent on the amount of oil where the size of silica particles increased as the amount of oil increased. The specific surface areas of samples measured using the BET method were 186 to 230 ㎡/g. X-ray fluorescence (XRF) analysis results showed that the SiO2 content was more than 90% while sodium was 3.27~4.5 wt. %. The spherical silica prepared in this study could be optimized for mass synthesis and commercialization because the industrial sodium silicate solution was used as a precursor of Si as well as the minimum amounts of hexane and nonionic surfactant were employed.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.30 no.3 s.47
• /
• pp.399-404
• /
• 2004

Novel GHK-conjugated chitosan was prepared by the solid-phase method using $N^{\alpha}-Fmoc$ amino acids/BOP coupling reagent. For this purpose, the chitosan microbeads which had a mean diameter of 70 um were prepared by the W/O emulsion-phase separation method. The GHK was successfully coupled to the chitosan microbeads by stepwise solid-phase method. The result of amino aid analysis was in good agreement with the theoretical values; $Gly_{1.02}\;of\;His_{1.13}\;Lys_{0.96).$. The cell proliferation effect of the GHK-bound chitosan microbeads was measured by MTT assay. We concluded that GHK-bound chitosan microbeads gave higher cell Proliferation effect than chitosan microbeads.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.21 no.2
• /
• pp.1-21
• /
• 1995

In this context, it should be mentioned that multilamellar vesicles can be prepared with the main compounds of the intercellular lipids, ceramides, cholesterol, cholesteryl ester, squalane, lecithin, wax ester by effect of the wetting. We investigated properties formation of MLV with use of the AHAsomes and Microfluidizer. The multilamellar vesicles are formed merely adding polyol and water phase, followed with the microfluidizer. Formation of a practically pure AHAsomes system, containing the active ingredients directly incorporated without need for preservatives. There were very good encapsulated properties of the active ingredients whether hydrophilic(malic acid, tartaric acid, lactic acid, allantoin, urea) and hydrophobic(vitamin-I acetate, vitamin-A palmitate). Optimum condition (ormatiom of MLV was passed three times in the microfluidizer, particle size of the vesicles should be within range 50-523nm (mean=163.5nm). As application, It was compared that horny layer of the sole of foots removal with the general OM emulsion and the AHAsomes cream. There was used for three months, those got recovery wrinkles about 151.8% and elasticity three times more the AHAsomes than O/W emulsions, It was confirmed with the Image Analyzer and the Cutometer.

• Applied Chemistry for Engineering
• /
• v.24 no.5
• /
• pp.471-475
• /
• 2013

This study is about photosensitive microspheres prepared by coating alginate microspheres with gelatin-cinnamic acid conjugate. Firstly, alginate microspheres was prepared in water-in-oil (W/O) emulsion and then they were coated with gelatin- cinnamic acid conjugate. Herein, gelatin-cinnamic acid conjugate is obtained by the amidation between an amine group of gelatin and a carboxy group of cinnamic acid. Cinnamic acid is widely used as a photo-responsive material easy to dimerize and dedimeriz under UV irradiation at ${\lambda}$ = 254 nm and ${\lambda}$ = 365 nm, respectively. As shown in SEM-EDS, alginate was successfully coated with gelatin-ciannmic acid. By determining the absorbance of coated microspheres at 270nm, the amount of cinnamic acid per microspheres was 0.13/1. The SEM photos showed the size of coated microspheres is around $10{\mu}m$. And the degrees of dimerization and dedimerization were calculated to be 49% and 23% respectively. Then the release of FITC-dextran from the coated micrspheres was studied and release the degree was 42%. As a result, the coated microspheres have potential to be used as a photo-responsive drug carrier to delivery drugs.

• Clean Technology
• /
• v.15 no.3
• /
• pp.194-201
• /
• 2009

Reductive reactivity of zero-valent iron nanoparticles was investigated for removal of nitrate-nitrogen which is considered one of the major water pollutants. To elucidate the difference in reactivity between preparation methods, iron nanoparticles were synthesized respectively from microemulsion and aqueous solution of ferric ions. Iron nanoparticles prepared from microemulsion were deposited on aluminum by electrophoretic method, and their reaction kinetics was compared to that of the same nanoparticles suspended in aqueous batch reaction. With an approximation of pseudo-first-order reaction, rate constants for suspended nanoparticles prepared from microemulsion and dilute aqueous solution were $3.49{\times}10^{-2}min^{-1}$ and $1.40{\times}10^{-2}min^{-1}$, respectively. Iron nanoparticles supported on aluminum showed ca. 30% less reaction rate in comparison with the identical nanoparticles in suspended state. However, supported nanoparticles showed the superior effectiveness in terms of nitrate-nitrogen removal per zero-valent iron input especially when excess amounts of nitrates were present. Iron nanoparticles deposited on aluminum maintained reductive reactivity for more than 3 hours, and produced nitrogen gas as a final reduction product of nitrate-nitrogen.

• Journal of the Korean Magnetics Society
• /
• v.16 no.1
• /
• pp.60-65
• /
• 2006

In order to investigate the dependence of the particle size on the cation distribution in the spinel structure, Mossbauer spectra were taken in the presence of an external magnetic field f3r the magnetic nanoparticles prepared by using a microemulsion method. The crystals are found to have a cubic structure. The results show that as the particle sizes decrease, $Fe^{3+}$ ions migrate from the octahedral site to tetrahedral site.

• Elastomers and Composites
• /
• v.44 no.3
• /
• pp.222-231
• /
• 2009

Shirasu-porous-glass (SPG) membrane emulsification is highly attractive in the field of toner industries, foods and drug delivery systems because of its easy control of particle size in micro-scale, narrow size distribution and multiple emulsion. The particle size and morphology of emulsion droplets can be controlled by changing the type of initiators, additives, monomers, crosslinkers and inhibitors in SPG membrane emulsification. In this paper, principles of SPG membrane emulsification, influence of process parameters and industrial applications have been addressed.

• Journal of the Korean Applied Science and Technology
• /
• v.21 no.1
• /
• pp.17-23
• /
• 2004

Silver bromide particles from 50 to 200${\AA}$ in diameter are prepared by mixing two microemulsions contaning the precursor salts $AgNO_3$ and KBr. The microemulsions are composed of AOT(bis(2-ethylhexyl) sodium sulfosuccinate), n-heptane and water. The particle diameters are measured on photomicrographs obtained by transmission electron microscopy. The size of the particles is generally larger than that of the water cores. The influence of both the concentration of precursor salts in the water cores of the microemulsoin and the size of these water cores on the size of the particles has been studied.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.400-401
• /
• 2008

전기영동형 전자종이 디스플레이의 새로운 소재로써 $C_{60}$(fullerene)와 같은 나노 입자를 포함하는 새로운 전기영동 입자를 제조하였다. 본 연구에서는 안정제로 poly(vinyl pyrrolidone)(PVP)를 사용하여 fullerene을 포함하는 styrene emulsion을 안정화 한 후 라디칼 중합을 통해 fullerene이 포함된 polystyrene microemulsion particles을 제조 합으로써 입자의 분산안정성을 높이고 전기영동에 따른 입자의 움직임을 최적화하도록 하였다. 이 실험에서는 fullerene의 양에 따라 제조된 입자의 크기와 입자 분포를 관찰하였다. 입자의 크기와 입자 분포는 주사형 전자현미경 (SEM) 을 이용하여 확인하였다. 또한 fullerene-PS 입자의 구조 분석과 특성평가를 위해서 FT-IR를 측정하였고, 입자의 열적 성질을 위해 TGA를 측정하였다.