• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.10 no.6
• /
• pp.335-342
• /
• 1985

A planar waveguide model is presented for calculating dispersion characteristics with the frequency dependent effective dielectric constant in microstrip lines and results are compared by the variation of each parameter. It is compared to use a wide range of relative dielectric constants and the strip $h_{width}$strate height, W/h ratios, 0.9$\leq$W/h$\leq$2. As the result of a computer simulation, the normalized phase velocity using a planar waveguide model for each case is more closely approached to 1/$\sqrt{\epsilon_r}$ as the increasing of the frequency than the other method that has already been presented.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.1
• /
• pp.8-15
• /
• 1998

In this paper, to improve the bandwidth of microstrip antenna, we discussed parasitic patch structure coupled capacitively at radiating slot. To reduce the overal size of antenna,$\lambda$/4 short structure is accepted instead of $\lambda$/2 patch. Since ground plane is reduced, backward radiation is occurred. The characteristics of the designed antenna is evaluated, based on the transmission line model and the aperture analysis method. And by computer program the radiation pattern and return loss are evaluated. As simulation results, backward radiation is -15 dB. Bandwidth of constructed antenna is 167 MHz at the resonant frequency of 2.45 GHz, which is very broad, compared to conventional microstrip antennas. Therefore the proposed antenna will be suitable for very wide bandwidth communications.

• Journal of Software Assessment and Valuation
• /
• v.16 no.1
• /
• pp.89-94
• /
• 2020

In this paper, we propose a software algorithm that can configure n-key roll-over that detects all keys without limitation on the number of pressed keys in the dynamic scanning detection of a keyboard composed of a matrix. The proposed algorithm uses the timer interrupt of the microcontroller for computer keyboard control, so that a constant and accurate detection interval can be obtained, and an accurate debounce time can be provided. In order to confirm the effectiveness of the proposed algorithm, a microcontroller was connected to a toy keyboard constructed in the form of a clavier and experiments were conducted. As a result of the experiment, it was confirmed that detection of all keys was performed accurately regardless of the number of keys pressed.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.25 no.2
• /
• pp.95-107
• /
• 2009

The purpose of this research was to examine the fitness of zirconia cores that were made by different sintering methods; generic electricity furnace and microwave furnace. Firstly, 12 cores for each group were made by using each different sintering process and attached them to a metal die with silicon. The internal and marginal gap of sintered zirconia was measured by using Skyscan 1076 micro-CT, then it was reorganized by CT-An software. To each samples, we extracted B-L image, M-D image of cutting side, and cross-sectional side of tooth long axis and calculated the mean value of marginal, axial, and occlusal gap each side. Results: 1. The mean marginal gap of sintered zirconia was $36.20{\mu}m$ for EVE, $47.67{\mu}m$ for LAV, $52.47{\mu}m$ for DEN, and $54.63{\mu}m$ for CER. 2. For the axial wall, the research showed the largest value of $63.49{\mu}m$ for EVE, but there were no statistical significance. 3. In related to the occlusal internal measurement, DEN showed the smallest value ($77.06{\mu}m$), EVE and CER showed significantly high value. From this study, it is suggested that CAD/CAM zirconia core which was made in the process of microwave sintering has clinically acceptable values in marginal and internal gap.

• Journal of the Korea Society of Computer and Information
• /
• v.10 no.5 s.37
• /
• pp.123-132
• /
• 2005

In this Paper, we present an improvement of switch node for wavelength multiplex optical network. Currently because of quick increase of internet traffic a big network capacity is demanded. Wavelength multiplex optical network Provides the data transfer of high speed and the transparent characteristic of the data. Therefore optic network configuration is the most powerful technology in the future. It will be able to control the massive traffic from the optical network in order to transmit the multimedia information of very many quantify. Consequently the node where the traffic control is Possible, is demanded. The optical switch node which manages efficiently the multiple wavelength was Proposed. This switch is composed of a optical switch module for switching and a wavelength converter module for wavelength conversion. It will be able to compose the switch fabric without optical/electro or electro/optical conversion using optical MEMS(Micro Electro Mechanical Switches) module. Finally, we present the good test result regarding the operational qualify of the switch fabric and the performance of optical signal from the switch node. The proposed switch node of the optic network will be able to control the massive traffic with all optical.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.2
• /
• pp.99-107
• /
• 2006

Magnetic nondestructive testing is very useful far detecting a crack on the surface or near of the surface of the ferromagnetic materials. The distribution of the magnetic flux leakage (DMFL) on a specimen has to be obtained quantitatively to evaluate the crack. The magnetic camera is proposed to obtain the DMFL at the large lift-off. The magnetic camera consists of a magnetic source, magnetic lens, analog to digital converters (ADCs), interface, and computer. The magnetic leakage fields or the distorted magnetic fields from the object, which are concentrated on the magnetic lens, are converted to analog electrical signals tv arrayed small magnetic sensors. These analog signals are converted to digital signals by the ADCs, and are stored, imaged, and processed by the interface and computer. However the magnetic camera has limitations with respect to converting and switching speed, full range and resolution, direct memory access (DMA), temporary storage speed and volume because common ADCs were used. Improved techniques, such as those that introduce the operational amplifier (OP-Amp), amplify the signal, reduce the connection line, and use the low pass filter (LPF) to increase the signal to noise ratio are necessary. This paper proposes the exclusive embedded ADC including OP-Amp, LPF, microprocessor and DMA circuit for the magnetic camera to satisfy the conditions mentioned above.

• Journal of the Korea Society of Computer and Information
• /
• v.14 no.5
• /
• pp.183-193
• /
• 2009

Both On-Line Analytical Processing (OLAF) data cubes and Statistical Databases (SDBs) deal with multidimensional data sets. and both are concerned with statistical summarizations over the dimensions of the data sets. However, there is a distinction between the two that can be made. While SDBs are usually derived from other base data, OLAF data cubes often represent directly the base data. In other word, the base data of SDBs are the macro-data, whereas the core cubiod data in OLAF data cubes are the micro-data. The base table in OLAF is used to populate the data cube with values of the measure attribute, and each record in the base tables is used to populate a cell of the core cuboid. The fact that OLAF data cubes mostly represent the micro-data may make some records be absent in the base table. Some cells of the core cuboid remain empty, if corresponding records are absent in the base table. Wang and others proposed a method for securing OLAF data cubes against privacy breaches. They assert that the proposed method does not depend on specific types of aggregation functions. In this paper, however, it is found that their assertion on aggregate functions is wrong whenever any cell of the core cuboid remains empty. The objective of this study is to design an inference control process in OLAF data cubes which rectifying Wang's error.

• Communications of Mathematical Education
• /
• v.14
• /
• pp.197-215
• /
• 2001

최근 수학적 사고력 연구가 구체적 수학내용에 기반한 활동과 조작에 대한 연구보다는 활동이나 조작을 통한 결과로 수학적 사고력에 접근하는 일회성 연구로 이루어지는 경향이 있다. 본고에서는 교육 내용을 선정하기 위해 학교수학에서 아동들이 어떤 수학적 사고를 하는데 장애을 겪는지에 주목하여, 이러한 장애를 극복하는 것을 통해 수학적 사고력의 신장을 생각해보고자 하였다. 이에 대수에서는 문자도입에 따른 추상적 상징의 수용과 이용부분에서, 기하에서는 논증기하의 증명도입과정에서 형식적, 연역적 사고 시작으로 아동이 수학적 사고에 어려움을 겪는다는 사살에 주목하였다. 특히 논증 기하의 연역적, 형식적 증명은 논리와 추론이 바탕이 되어야 한다. 그런데 논리와 추론은 고등학교 1학년과정 집합과 명제부분에 들어있어 아동은 논리와 추론에 대한 어떤 경험도, 교육도 받지 않은 상태에서 증명을 하게 된다. 이에 교육 내용으로 수학적 사고력을 신장을 위해 가장 필요한 내용이 논증 기하가 도입되기 이전에 초등학교 5,6학년 아동을 대상으로한 논리와 추론교육이라고 본다. 또한 교육 방법으로는 컴퓨터를 이용한 교육공학적 접근을 하고자 하였다. 교육공학적 접근이 적극 권장되는 교육적 현실과 정규교육과정에서 이를 받아들일만한 시간적 여유가 없음을 감안하여, 교과 내용과 연계된 컴퓨터 교육을 제안하는 바이다. 이에 논리 및 추론 교육은 컴퓨터 교육으로 초등학교의 특기적성 시간이나 정규수업 시간에 이용할 것을 제안한다. 논리와 추론교육을 위해 무엇을 어떻게 가르칠 것인가에 대한 답으로 논리와 추론교육에 적합한 수학적 내용으로 크게 이산수학과 중등 기하의 초등화하여 탐구하도록 하는 내용을, 교육 방법 측면에서는 논리와 추론 교육을 위한 LOGO 기반 마이크로월드를 설계, 이용하여 수학적 사고력을 신장시키고자 한다. 여기까지가 수학적 사고력을 위한 가능성을 모색한 것이라면 후속연구로 이러한 가능성을 실험연구로 검증하고자 한다.

• Journal of Educational Research in Mathematics
• /
• v.17 no.2
• /
• pp.111-125
• /
• 2007

In this article, we introduce an example about 'computers and mathematics education' and discuss its educational meaning. First, we survey two microworlds of Logo and DGS, which are two different representation systems for geometric phenomena. And we propose needs of connecting two microworlds with common perspective. And we suggest a mediation model that connects two representations in a microworld. Using this mediation model(Circle model), we construct a circle, a ellipse, and a cardioid with two different representations. It is important that the mediation model makes it possible that we translate descriptions from one representation into the other, and guess perimeters of planar curves. We also discuss roles and mathematical implications of this mediation model by error case in calculating perimeters of ellipses.

• Journal of the Korea Society of Computer and Information
• /
• v.25 no.3
• /
• pp.1-9
• /
• 2020

In this paper, we propose an efficient adaptive write scheme that improves the performance of write operation in MLC STT-MRAM caches. The key idea of the proposed scheme is to perform the write operation fast if the target MLC STT-MRAM cells contain a dead block. Even if the fast write operation on the MLC STT-MRAM evicts a cache block from the MLC STT-MRAM cells, its performance impact is low if the evicted block is a dead block which is not used in the future. Through experimental evaluation with a memory simulator, we show that the proposed adaptive write scheme improves the performance of the MLC STT-MRAM caches by 17% on average.