• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.247-247
• /
• 2004

세라믹의 완전 소결체는 높은 경도와 취성을 가지기 때문에 연삭과 같은 입자가공이 행해지게 되어, 가공능률이 매우 낮고, 복잡한 형상 창성이 어렵다. 완전소결된 세라믹의 절삭가공에서는, 공구수명이 짧고, 가공속도가 매우 늦어 일반의 부품가공에 적용하기 어렵다. 또한 소결이 전혀 행해지지 않은 성형체의 절삭가공은 공작물의 강도가 약하기 때문에 가공속도, 가공능률, 부품의 척킹 및 치수 정밀도 등에 문제가 있다고 할 수 있다 이러한 문제 때문에 엔지니어링 세라믹의 고능률, 고품위 절삭에 관한 연구가 필요하다.(중략)

• Journal of the KSME
• /
• v.25 no.2
• /
• pp.153-157
• /
• 1985

치차의 마찰손실은 일반적으로 낮으나, 치면의 온도상승을 초래하여 마멸을 증대시키거나 치면의 강도를 저하시킨다. 이것은 결과적으로 치차의 강도(부하특성)에 직접적인 관계를 갖고 있기 때문에 마찰손실을 가능한 한 낮게 유지하여야 한다. 치차의 맞물림은 치면의 미끄름속도 미 끄름율, 곡율반경 및 하중이 맞물림중에 순간적으로 변하므로 해석이 간단하지 않다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.1
• /
• pp.154-159
• /
• 1987

In the previously reported Part I, the behavior of the flank wear for carbide tool was studied as a preceeding step to present a simple method for Quick Tool-Life Testing, and the following general equation was obtained $W_{f}$ =(a+bt) $V^{m}$ . In this study the following step-cutting formula for the constants a, b and m in the above general model is derived by using step-cutting data [a numerical formula] To check the validity of the above formula, the comparison is made between the tool-life equation inferred in this method and that inferred in the conventional tool-life testing method, when the wear criterion is 0.3mm. The equation obtained in the present method is V(T')$^{0.57}$=1763 whereas the equation obtained in the conventional tool-life testing method is V(T)$^{0.56}$=1605 The results of the above two formula are satisfactory and also verify the validity of the present research.earch.

• Journal of KSNVE
• /
• v.7 no.6
• /
• pp.1015-1023
• /
• 1997

Rotordynamic analysis of a multistage turbine pump using finite element method is performed to investigate the effects of seal wear on its system behavior. Stiffness and damping coefficents of the 2-axial grooved bearing are obtained as functions of rotating speed. Stiffness and damping coefficients of plane annuler seals are calculated as functions of rotating speed as well as seal clearance of seals become larger, these stiffness and damping coefficients decrease drastically so that there can be significant changes in whirl natural frequencies and damping characteristics of the pump rotor system. Although a pump is designed to operate with a sufficient seperation margin from the 1st critical speed, seal wear due to long operation may cause a sudden increase in vibration amplitude by resonance shift and reduce seal damping capability.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.2
• /
• pp.228-236
• /
• 2002

In this study, the carbon steels, SM20C were machined with the tungsten carbide tipped circular saw to clarify the cutting-off characteristics in terms of tool wear. The results show that an improved performance in view of both the tool wear and the cutting efficiency was obtained by using oil base cutting fluid at the cutting speed of 100m/min with the feed of 0.06mm/tooth. The rake angle of 10$^{\circ}$ , clearance angle of 8$^{\circ}$ , nose radius of R0.1mm, and end cutting edge champer of 0.1mm$\times$25$^{\circ}$ are believed as the best tool geometries. The tool wear decreases due to using the saw of the disk of STS5 and the tool material of P30.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.115-121
• /
• 2001

The wear test has been performed to evaluate the wear mechanism of steam generator (SG) tube materials against ferritic stainless steel in water environment. The wear rates of SG tube materials depend on the change of mechanical properties between contact surfaces during wear test. From the subsurface hardness test, Inconel 690 is more work-hardened than Inconel 600 even though these materials have similar hardness values before the wear test. Main cause is due to the difference of stacking fault energy with the chromium content. In water environment, wear mechanism is closely related with the continuous formation and fracture of deformation layers at the contact surfaces.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1995.06b
• /
• pp.7-13
• /
• 1995

현재 교통인구 비중에 큰 비중을 차지하고 있는 철도 차량은 기술의 발전으로 인한 고속화에 성공하여 300km/h대의 속도를 달성하기에 이르렀다. 열차가 고속화됨으로 인하여 열차 주행시 운동에너지가 더욱 커졌고 이를 소산하기 위한 제동 역시 더욱 중요하게 되었다. 열차의 제동시 중요한 점은 wheel의 skidding을 방지함으로 wheel의 편마멸을 줄이는 것이며 이를 위해선 제동장치의 설계시 wheel과 rail간의 점착현상의 이해가 필수적이다. 제동력이 점착력보다 클 경우는 skidding이 발생하며 제동력이 점착력보다 작은 경우는 충분한 제덩을 하지 못한다는 것을 의미한다. 그러므로 열차의 제동장치를 설계함에 있어서 점착계수는 필수적인 요소가 되었으며 미국, 일본, 독일 등의 선진 각국에서는 점착계수를 측정하여 그 특성을 파악하려는 실험이 실험실 및 실차 차원에서 많이 행하여졌다. 각각 다른 접척조건, 속도 등에 따른 실험이 진행되어 왔으나 각 연구의 결과는 조금씩 다른 결향을 나타내었고, 점착현상에 관한 물리적인 설명은 못하고 있는 실정이다. 본 연구에서는 wheel과 rail의 접촉인 경우에 있어 점착현상의 변화를 속도, 하중, 접촉조건에 따른다고 보고 점착현상의 특성을 각각 sliding, pure rolling실험을 통해 파악하고 기타 참고문헌에서 발표된 점착계수와 비교하여 물리적으로 이해하고자 하였다.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2000.06a
• /
• pp.31-36
• /
• 2000

평면연삭은 기계부품의 후가공 공정에 사용되며, 기계부품의 다듬질면은 내마멸성, 피로강도 및 내식성등 품질에 큰 영향을 미친다. 연삭작업중 가장 큰 위험 요소는 고속작업중 연삭숫돌의 파손이다. 연삭숫돌의 파괴되는 주요 원인은 고속 회전중 최고사용 원주속도를 넘어 지나치게 빠를 때 원심력이 결합력보다 커지는 경우와, 숫돌에 균열(crack)이 있을 때이다. 연삭숫돌이 파괴되어 숫돌 파편이 작업자의 머리, 안면등을 강타하여 사망이나 골절등 중대재해가 발생된다. (중략)

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.10
• /
• pp.2597-2605
• /
• 1994

The wear behavior of two types of $Si_3N_4$ exposed to high and low humidity was examined at various sliding speeds, using bearing steel as disk material under pin-on-disk type sliding conditions. Higher wear rates were obtained at a high humidity than at a low humidity. As the sliding speed was increased, the wear rates were decreased and the effect of humidity on the wear rates of $Si_3N_4$ was reduced. The result that the $Si_3N_4$ pin showed higher wear rate under the high humidity condition was explained by the decrease in microhardness of $Si_3N_4$ due to the chemisorbed moisture on the pin and plowing action by the hard particles of $Fe_2O_3$ from the disk. An increase in the sliding speed is supposed to reduce the effect of humidity on the wear rate of $Si_3N_4$ by raising the average temperature of the disk surface and the local temperature at pin-disk contact point.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.1
• /
• pp.1-6
• /
• 2012

The polishing of silicon wafers has an important role in semiconductor manufacturing. Generally, getting a flat surface such as a mirror is the purpose of the process. The wafer surface roughness is affected by many variables such as the characteristics of the carrier head unit, operation, speed, the pad and slurry temperature. Optimum process conditions for experimental temperature, pH value, down-force, slurry ratio are investigated, time is used as a fixed factor. This study carried out a series of experiments at varying platen, chuck rpm and oscillation cpm taking particular note of the difference between the rpm and the affect it has on the surface roughness. In this experiment determine the optimum conditions for polishing silicone wafers.