• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.3
• /
• pp.318-325
• /
• 2019

As satellite communication technology with high efficiency and spatiality evolves, demands of customer for efficient and effective satellite broadcasting services are increasing due to interval reduction of the between satellites, and the limited radio-frequency spectrum resources. Recently, research on antenna that it possible to simultaneously receive multiple signal from various satellites while holding maintain the same number of previous reception channels by using the single reflector has been ongoing. It is necessary to be able to simultaneously receive signals from various satellites in order to maintain the same number of previous reception channels. We suggest a multiband antenna which can be simultaneously and independently receiving Ku band and Ka band satellite broadcasting signals transmitted by three adjacent satellites. We have designed and simulated using commercial design tools TICRA CHAMP and CST MWS to meet the target specifications. It appears that the antenna has -10 dB return loss, and more than 40 dBi directivity gain in Ku band and Ka band respectively.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.17 no.2
• /
• pp.93-98
• /
• 2024

This paper presents the method to extract the ultrawide-band (UWB) signal and proposes the simple impulse radar system for sensing real-based target within close-range area. The proposed impulse radar system consists of impulse generator, ultrawide-band antennas, function generator, and digital oscilloscope. It is verified by experiment that a differentiated Gaussian pulse is generated with 200ps of pulse width and corresponding spectrum from 0.3 to 4.7 GHz once a sinusoidal wave with 10MHz is excited. The Gaussian doublet is received by identical antennas and it is shown that the UWB pule width of 328ps and its spectrum is from 0.9 to 4.4 GHz. It is confirmed that the UWB pulse is extracted when the real-based targets such as circular target with 4cm radius and corner reflector are placed at the close-range area.

• Proceedings of the KSRS Conference
• /
• 2009.03a
• /
• pp.155-158
• /
• 2009

본 논문에서는 DLR(German Aerospace Center)에서 운영하는 TerraSAR-X를 이용하여 2009년 1월 19일 18:28 (Local time) 에 서해 대부도/제부도 및 대부도 남쪽 해안을 촬영한 stripmap mode (Dual-Pol: HH, VV) 화상을 취득하여 향후 고해상도 X-밴드 화상의 활용 방안 및 효용성에 대해 검토해 보았다. 함께 취득된 현장자료와의 비교를 통하여 2010 년에 발사될 예정인 아리랑 5 호의 활용방안을 찾고자 한다. 여기서는, 연안에 설치된 양식시설, 소형 선박 그리고 코너리플렉터에 대해서 해석을 수행하였다. 김 양식시설의 경우, 구조와 설치 각도에 따라 다른 후방산란특성을 보였으며, 같은 시설에 대해서도 HH 편파의 후방산란계수가 VV 보다 2.6 dB 높게 나타났다. 그 이유는 김 양식시설이 TeraSAR-X의 전파전파 방향과 수직하게 되어 후방 산란이 많이 일어나는 반면에, B 지역에 설치된 김 양식시설은 TeraSAR-X의 전파전파방향과 약 45 도 비스듬하게 설치되어 있어, 상대적으로 낮은 후방산란계수를 나타내기 때문이다. 또한 한 변의 길이가 각각 1 m, 0.6 m 인 사각면 삼각 수동 전파반사기 두 개를 제부도 북쪽의 갯벌에 설치하여 TerraSAR-X 의 화상에 나타난 후방산란특성을 분석하였다. TerraSAR-X 의 화상이 X-밴드를 사용하고, 높은 해상도로 인해 power spill이 넓게 분포하는 것을 볼 수 있다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.2 no.4
• /
• pp.643-652
• /
• 1998

This paper presents the characteristics of a relay station antenna with the newly designed back-plate structure which is composed of the U-shaped metal plate for suppression of the back lobe by edge diffraction. The back lobe level of the conventional type was about -20 dB in the -z direction ( 180 ) . In order to improve the characteristics, the U-shaped mesh type metal plate is considered, where the design condition of the model antenna satisfies the wide null point angle range with the back lobe level of -30 dB below in the -z direction. The design parameters with the minimum back lobe level such as the dipole length, the distance between dipole elements and the back plate size have been found by using the released NEC Win Pro code. The calculated and measured back lobe Bevel of model antenna have been obtained 48.48 dB and -45 dB at 325 MHz, respectively.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.24 no.1
• /
• pp.12-16
• /
• 1988

The observation of the tidal current and the bottom contour around the set net fishing ground were carried out at four different regions of the southern part of Korea in order to obtain the basic information on the migrating course of fishes. The bottom contour was surveyed with portable echo sounder, and the tidal current was observed by two different methods at the same time. One was 25 hour observation at the fixed position with self-recording current meter (Inter Ocean Model 135 type) and the other was the drift observation of radar reflectors. Most of the set nets have been set near bottom valleys. It was regarded that the fish school became to dense easily near the valley according to the combined effect of the tidal current and the bottom contour.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.11
• /
• pp.1185-1192
• /
• 2008

In this paper, a wideband LC oscillator which is composed of a high voltage switch and a fat dipole antenna was designed and radiation characteristics are analyzed. A Marx generator was used as a high voltage pulse generator of the proposed wideband LC oscillator and $90^{\circ}$ corner reflector was used to obtain high directivity. According to simulated and measured results, 3 dB bandwidth of high voltage switch without fat dipole based on the received power is about 9%(${\lambda}_1=0.7\;m$) and bandwidth Is about 30%(${\lambda}_2=1\;m$) by using the LC oscillator containing high voltage switch and fat dipole. Consequently, fat dipole affects not only radiating power but also operating frequency and bandwidth of the LC oscillator. This study will be useful to determine operating frequency and radiating power when we design LC oscillator which uses a high voltage switch and a fat dipole.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.10
• /
• pp.758-765
• /
• 2018

This paper presents a 24-GHz frequency-modulated continuous wave(FMCW) radar transceiver with two Rx and one Tx channels in 65-nm complementary metal-oxide-semiconductor(CMOS) process and implemented it on a radar system using the developed transceiver chip. The transceiver chip includes a $14{\times}$ frequency multiplier, low-noise amplifier, down-conversion mixer, and power amplifier(PA). The transmitter achieves >10 dBm output power from 23.8 to 24.36 GHz and the phase noise is -97.3 GHz/Hz at a 1-MHz offset. The receiver achieves 25.2 dB conversion gain and output $P_{1dB}$ of -31.7 dBm. The transceiver consumes 295 mW of power and occupies an area of $1.63{\times}1.6mm^2$. The radar system is fabricated on a low-loss Duroid printed circuit board(PCB) stacked on the low-cost FR4 PCBs. The chip and antenna are placed on the Duroid PCB with interconnects and bias, gain blocks and FMCW signal-generating circuitry are mounted on the FR4 PCB. The transmit antenna is a $4{\times}4$ patch array with 14.76 dBi gain and receiving antennas are two $4{\times}2$ patch antennas with a gain of 11.77 dBi. The operation of the radar is evaluated and confirmed by detecting the range and azimuthal angle of the corner reflectors.

• Journal of Energy Engineering
• /
• v.28 no.4
• /
• pp.35-41
• /
• 2019

In order to overcome these disadvantages, the halogen light source, which was previously used as a vehicle fog light, has increased power consumption and a short lifetime, and thus, an automobile light source is gradually being replaced with an LED. However, when the vehicle LED fog light is turned on, there is a disadvantage in reducing the life of the fog lamp due to the high heat generated from the LED. The heat generated by the LED inside the fog lamp is mainly emitted by the heatsink, but most of the remaining heat is released to the outside through convection. When cooling efficiency decreases due to convection, thermal energy generates heat to lenses, reflectors, and bezels, which are the main parts of lamps, or generates high temperatures in LED, thereby shortening the life of LED fog lights. In this study, we tried to improve the heat dissipation performance by convection in addition to the heat dissipation method by heat sink, and to determine the installation location of vents that can discharge the internal air or intake the external air of LED fog lamp for vehicle. Thermal fluid analysis was performed to ensure that the optimal data were reflected in the design. The average velocity of air increased in the order of Case3 and Case2 compared to Case1, which is the existing prototype, and the increase rate of Case3 was relatively higher than that of other cases. This is because the vents installed above and below the fog lamps induce the convective phenomena generated according to the temperature difference, and the heat is efficiently discharged with the increase of the air speed.

• Journal of the Microelectronics and Packaging Society
• /
• v.16 no.1
• /
• pp.13-19
• /
• 2009

A 440MHz wireless and passive surface acoustic wave (SAW) based chemical sensor was developed on a $41^{\circ}YX\;LiNbO_3$ piezoelectric substrate for simultaneous measurement of $CO_2$ gas and relative humidity (RH) using a reflective delay line pattern as the sensor element. The reflective delay line is composed of an interdigital transducer (IDT) and several shorted grating reflectors. A Teflon AF 2400 and a hydrophilic $SiO_2$ layer were used as $CO_2$ and water vapor sensitive films. The coupling of mode (COM) modeling was conducted to determine optimal device parameters prior to fabrication. According to simulation results, the device was fabricated and then wirelessly measured using the network analyzer. The measured reflective coefficient $S_{11}$ in the time domain showed high signal/noise (S/N) ratio, small signal attenuation, and few spurious peaks. In the $CO_2$ and humidity testing, high sensitivity ($2^{\circ}/ppm$ for $CO_2$ detection and $7.45^{\circ}/%$RH for humidity sensing), good linearity and repeatability were observed in the $CO_2$ concentration ranges of $75{\sim}375ppm$ and humidity levels of $20{\sim}80%$RH. Temperature and humidity compensations were also investigated during the sensitivity evaluation process.