• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.7
• /
• pp.469-478
• /
• 2019

Multirotor configurations such as VTOL and urban air mobility have been focused on today due to the high maneuverability. Aerodynamic and aeroacoustic characteristics of multirotor have much difference to those of a single rotor. In this study, a numerical analysis based on the free wake vortex lattice method is used for identifying the wake interaction effect. In order to compare the various configurations and operating conditions, the effects of the spacing between the rotors in hovering flight and the effects of the advancing ratio and the formation in forward flight are discussed. In the hovering flight, the unsteady loading of multirotor changes periodically and loading fluctuation increases as decreasing the spacing. It causes the variation in unsteady loading noise and the noise directivity pattern. In the forward flight, the difference in loading fluctuation and noise characteristics are observed according to the diamond and square formation of rotors. By comparing with results of single rotor analysis, multirotor configurations have different directivity pattern and amplitude of loading noise according to the location of each rotor. As a result, wake interaction effect becomes a highly important factor for aerodynamic and aeroacoustic analysis according to multirotor configurations and operating conditions.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.10
• /
• pp.920-927
• /
• 2015

In this paper, numerical results of sectional analysis and stress recovery were compared with the results of VABS through the blade analysis library. The results of recovery analysis for one-dimensional model including the stiffness matrix is compared with the calculated three-dimensional stress results of three-dimensionial FEM based on the principle of virtual work. We discuss the configuration of the blade analysis library and compare verifications of numerical analysis results of VABS. Blade analysis library through dimensional reduction and stress recovery is intended to be utilized in conjunction with pre- and post-processing of the analysis program of the composite blade, high-altitude uav's wing, wind blades and tilt rotor blade.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.04a
• /
• pp.159-166
• /
• 1998

본 연구에서는 공기포일 베어링으로 지지된 로터 베어링 시스템을 구성하고 실험을 수행함으로써 시스템의 진동을 측정하고 그 결과를 해석함으로써 로터 베어링 시스템의 안정성 검토한다. 또, 초기 구동 마찰을 고려하여 공기윤활로만 구동되는 경우와 초기에 베어링 표면에 오일이 도포된 경우를 비교한다. Transient data를 해석 함으로써 로터 베어링 시스템의 startup 및 shutdown에 대한 특성 파악이 가능해지며 시스템의 동적 특성에 대한 더욱 정확한 해석을 가능케한다.

• The Journal of the Acoustical Society of Korea
• /
• v.37 no.2
• /
• pp.83-91
• /
• 2018

The noise sources of a tip-jet driven rotor can be separated by rotor blade noise and jet noise. The rotor blade noise consists of thickness noise, loading noise, nonlinear quadrupole noise, and jet noise is divided into nozzle momentum noise and jet radiation noise. The flow analysis for the prediction of rotor blade noise is performed by CFD (Computational Fluid Dynamics) analysis, and the noise source of the rotor blade noise is identified by simultaneously applying the permeable and impermeable surface based FW-H (Ffowcs Williams-Hawkings) acoustic analogy. The nozzle momentum noise is obtained by permeable surface FW-H, and jet radiation noise is predicted by using empirical method for the fixed-wing jet. Both of jet noises use nozzle exit condition for noise analysis. The accuracy of the technique is verified based on the noise measurements of the tip-jet driven rotor, and the unique noise characteristics of the tip-jet driven rotor is confirmed by spectrum analysis.

• Aerospace Engineering and Technology
• /
• v.7 no.1
• /
• pp.15-23
• /
• 2008

This paper describes the structural analysis results of KARI General Small-scaled Rotor Test System (GSRTS) operated in KARI to verify operational safety. This GSRTS was developed to conduct a froude and mach small-scaled rotor test. This analysis was performed to investigate the structural Factor of Safety for the various small-scale rotor system like articulated or hingeless rotor and to check the operational capability using given operational design load. Specially, drive system has several bearings, mechanical gears, shaft, etc. and these parts must be required to achieve an operational safety. The calculation was done by using geometric data and material properties by analytical method. This rotor test system should be operated within these calculated Factor of Safety. Furthermore, the operational limitation should be defined as applied to small-scale rotor system of KUH in future.

• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.39-44
• /
• 2005

To validate the rotor performance analysis, 3D Computational Fluid Dynamics(CFD) analysis was performed for tilt rotor aeroacoustic model(TRAM). Also, 3D vehicle with rotating rotors was simulated for rotor power effect analysis. Multiple reference frame(MRF) and sliding mesh techniques were implemented to capture the effect of rotor revolution. CFD results were compared with the wind tunnel test results to validate their accuracy. At helicopter mode, CFD analysis predicted lower thrust than the wind tunnel test but CFD results showed good agreement with the test result at cruise mode. Rotor power effect decreased the lift but did not change drag and pitching moment.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.1
• /
• pp.59-65
• /
• 2013

The objective of this paper is to analyze the structure of the wind power tree using a helical type wind turbine. The blades of a helical rotor is designed with a composite material. The structural analyses of a helical rotor have been implemented by finite element method. The structural analyses of the wind power tree which support four helical rotor, have been performed under a wind load, a rotational velocity of a rotor, and dead weight.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.10a
• /
• pp.64-69
• /
• 1997

정격속도 100,000RPM용 원심분리기(centrifuge) 로터베어링계에 대해 회전체동역학 해석이 수행된다. 시스템은 원심분리기 로터, 유연축, 모터 로터와 축, 그리고 모터축 지지용 두 개의 구름베어링으로 구성된다. 설계목표는 정격속도가 위험속도(critical speed)에 대해 충분한 분리여유를 갖고, 위험속도에서 로터의 양호한 불균형응답특성을 이루어 내는 것이다. 후자의 요구조건은, 시스템이 다수의 위험속도를 통과하며 정격속도 주위에서 충분한 분리 여유를 갖지 않을 수도 있기 때문에 특히 중요하다. 시스템에 초유연축(extra-flexible shaft)을 도입함으로써, 비록 1차 위험속도에서 만족스럽지 못한 큰 불균형응답을 가질지라도 고차 위험속도에서 만족스런 작은 불균형응답을 보인다. 1차 위험속도에서 로터의 큰 변위를 억제하기 위해서 범퍼링(bumper ring) 또는 안내베어링(guide bearing)을 유연축의 적절한 위치에 설치할 필요가 있다. 비록 유연축계라 할지라도 정격속도와 가까운 4차 이상의 고차 위험속도를 정확히 규명하기 위해서는 모터의 동역학을 전체시스템에 결합하여야 함을 볼 수 있다. 해석은 유한요소법(finite element method)에 의해 수행된다.

• Composites Research
• /
• v.19 no.6
• /
• pp.8-15
• /
• 2006

In this study, computational rotor dynamic analyses of a composite roller used for large LCD panel manufacturing process have been conducted. The present computational method is based on the general finite element method with rotating gyroscopic effects of rotor systems. General purpose commercial finite element code, SAMCEF which has special rotordynamics analysis module is applied. For the purpose of numerical verification, comparison study for a benchmark dual rotor model with support bearings is also presented. Detailed finite element models for composite roller with optimized lamination angles are constructed and analyzed considering gravity effect in order to investigate vibration characteristics in actual operation environment. As results of the present study, rotor stability diagrams and mass unbalance responses are presented for different rotating conditions.

• Journal of Aerospace System Engineering
• /
• v.17 no.2
• /
• pp.45-55
• /
• 2023

This study conducted aeromechanics modeling and structural load analyses of Tilt Rotor Aeroacoustic Model (TRAM), a 25% scaled V-22 tiltrotor model used in wind tunnel tests. A rotorcraft comprehensive analysis code, CAMRAD II, was used. Analysis results of this study in low-speed forward flights were compared with DNW test and previous analysis results. Blade flap bending moments were in good agreement with measured data. Mean values and oscillatory loads for lead-lag bending and torsion moments were slightly different from measured data. However, when mean values were removed, results of structural loads for one rotor revolution were moderately compared with wind tunnel tests and previous analyses. Total forces and half peak-to-peak forces of the pitch link reasonably well matched with previous analysis results and measured data. Finally, harmonic magnitudes of blade structural loads were investigated.