• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.2
• /
• pp.98-105
• /
• 2005

This paper presents the result of the aeroelastic stability test of the small-scaled hingeless hub system with composite paddle blades in hover and forward flight conditions. Excitation tests of hingeless hub system installed in GSRTS(General Small-scale Rotor Test System) at KARI(Korea Aerospace Research Institute) were carried out to get lead-lag damping ratio of blades with flexures as hub flexure. MBA(Moving Block Analysis) technique was used for the estimation of lead-lag damping ratio. First, blades with metal flexures, then with composite flexures of the same dynamic properties of rotor system as metal one were tested. Tests were done on the ground and in the wind tunnel according to the test conditions of hover and forward flight, respectively. Composite flexures were found to have better damping characteristics over metal ones in the non-rotating vibration test, and it was confirmed that the use of composite flexures would give observable improvement in aeroelastic stability compared to metal ones in all test conditions.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.11
• /
• pp.3110-3114
• /
• 2009

Rotor temperature variation is a significant issue in the design of induction motor controls. In the literature, numerous studies have mentioned significant performance degradation due to rotor temperature variation unless it is taken into account. However, those studies have mainly focused on field-oriented control in terms of tracking performance. There was little research about the influence of rotor temperature variation on performance particularly in the case of optimal controls such as maximum torque per amp (MTPA) control strategy. This work investigates how to affect the performance of maximum torque per amp (MTPA) control strategy as rotor temperature varies in time. To this end, investigation was carried out in two ways to see whether the objective of MTPA control strategy is achieved regardless of rotor temperature variation. It is to produce a desired torque with the minimum possible stator current at the same time. Laboratory experiment shows that tracking performance and maximum torque per amp condition is significantly affected by rotor temperature variation as rotor temperature varies, thus ending up with performance degradation of MTPA control.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.396-401
• /
• 2004

In this paper, a 1MW HAWT(FIL-1000) rotor blade has been designed by BEMT(Blade Element Momentum Theory) with Prandtl's tip loss. Also, a 3-D flow and performance analysis on the FIL-1000 rotor blade has been carried out by using the 3-D Navier-Stokes commercial solver (CFX-5.7) to provide more efficient design techniques to the large-scale HAWT engineers. The rated power and itsapproaching wind velocity at design point (TSR=7.5) are 1MW and 9.99m/s respectively. The rotor diameter is 54.5m and the rotating speed is 26.28rpm. Airfoils such as FFA W-301, DU91-W-250, DU93-W-210, NACA 63418, NACA 63415 consist of the rotor blade from hub to tip. Recent CFX version, 5.7 was adopted to simulate 3-D flow field and to analyze the performance characteristics of the rotor blade. Entire mesh node number is about 730,000 and it is generated by ICEM-CFD to achieve better mesh quality The predicted maximum power occurringat the design tip speed ratio is 931.45kW. Approaching to the root, the inflow angle becomes large, which causesthe blade to be stalled in the region. Therefore, k-$\omega$ SST turbulence model was used to predict the quantitative flow information more accurately. Application of commercial CFD code to optimum blade design and performance analysis was proved to be more effective environment to HAWT blade designers.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.4
• /
• pp.81-88
• /
• 2005

In order to estimate the gas turbine engine performance precisely, the component maps containing their own performance characteristics should be needed. In this study a component map generation method which may identify compressor map conversely from a performance deck provided by engine manufacturer using genetic algorithms was newly proposed. As a demonstration example for this study, the PW 206C turbo shaft engine for the tilt rotor type Smart UAV(Unmanned Aerial Vehicle). In order to verify the proposed method, steady-state performance analysis results using the newly generated compressor map was compared with them performed by EEPP(Estimated Engine Performance Program) deck provided by engine manufacturer. And also the performance results using the identified maps were compared with them using the traditional scaling method. When the performance analysis is performed at far away operation conditions from the design point, in case of use of e component map by the traditional scaling method, the error of the performance analysis results is greatly increasing. In the other hand, if in case of use of the compressor map generated by the proposed GAs scheme, the performance analysis results are closely met with those by the performance deck, EEPP.

• Proceedings of KOSOMES biannual meeting
• /
• 2005.05a
• /
• pp.135-140
• /
• 2005

Currently, ECDIS and GPS plotters are much used as equipment providing operators with route information, but they do not have any function of automatic route creation and route explanation, so available for only experienced operators. Especially, the present situation is tint no study is made of the automatic route creation and route explanation using ENC for ECDIS, substitution system of paper chart. ENC is the electronic navigation chart that is produced using S-52, S-57 standard format required by IHQ. In this paper, an Vessel Operator Support System(VOSS) is proposed to generate an optimal route where ENC and GPS data is fusioned induding the wind direction and speed of an anemometer and tide data. The proposed system was testified by a simulation, and its effectiveness was verified.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.2
• /
• pp.159-163
• /
• 2005

Marine accidents of 70.9% have been caused by small ships less than 100 tons in the past 5 years(1998${\sim}$2002). This is ascribable to the graying and lack in expertise on shipping of small ship operators, and merchant ships are hindered from coastal navigation due to the increase of coastal fishing boats and liners. Currently, ECDIS and GPS Plotters are widely used as navigation equipment providing route information to operators, but it can not give any function of automatic route creation and route explanation, so they are available only experienced operators. Especially, the present situation is that no study is made of the automatic route creation and route explanation using ENC for ECDIS, substitution system of paper chart. In this paper, Navigation Guiding System(NGS) is proposed to generate an optimal route where ENC and GPS data is fusioned including the wind speed and direction of anemometer. The proposed system was testified by a simulation, and its effectiveness was verified.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.3 s.246
• /
• pp.278-286
• /
• 2006

Experiments were conducted to estimate the performance of drag force type vertical axis wind turbine with an opening-shutting rotor. It was operated by the difference in drag force generated on both sides of the blades. The rotational speed was measured by a tachometer in a wind tunnel and the tunnel wind speed was measured by using a pilot-static tube and a micro manometer. The performance test for a prototype was accomplished by calculating power, power coefficient, torque coefficient from the measurement of torque and rpm by a dynamometer controller. Various design parameters, such as the number of blades(B), blade aspect ratio(W/R), angle of blades$(\alpha)$ and drag coefficient acting on a blade, were considered for optimal conditions. At the experiment of miniature model, maximum efficiency was found at N=15, $\alpha=60^{\circ}$ and W/R=0.32. The measured test variables were power, torque, rotational speed, and wind speeds. The data presented are in the form of power and torque coefficients as a function of tip-speed ratio V/U. Maximum power was found in case of $\Omega=0.33$, when the power and torque coefficient were 0.14 and 0.37 respectively. Comparing model test with prototype test, similarity law by advance ratio for vertical axis wind turbine was confirmed.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.22 no.6
• /
• pp.780-785
• /
• 2012

Wind energy is currently the fastest growing source of renewable energy used for electrical generation around the world. Generally, wind turbine systems are designed to be operated for twenty years long, Therefore, various faults in the wind turbine system inevitably occur during their long term period of operation. Especially, rotor shaft, gear-box and generator are installed inside of nacelle, furthermore, some cooling systems for normal operation of these devices are also required. If these cooing systems have failed in their operation, it is impossible for the entire system to be operated normally. In this work, IR(Infra Red) camera based fault detection system for the preventive detection of various cooling systems faults is proposed. To verify the applicability of the proposed system, physical implementation is embodied and various experiments are carried out.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.19-19
• /
• 2010

복합분자펌프는 기존의 터보분자펌프 turbine blade에 spiral grooved를 추가하여 초고진공 ($10^{-8}Pa$)에서 저진공(330Pa)까지 넓은 압력범위에서 사용할 수 있고 이 펌프를 사용함으로서 완전 oil free한 진공시스템을 만들 수 있는 특징을 가지고 있다. 특히, 회전체를 비접촉으로 지지하는 자기베어링 방식을 적용함으로써, 진동은 극히 작고 베어링수명은 길면서 중저진공에 대한 배기속도가 크고 임의의 방향으로 접속이 가능하여 반도체 및 디스플레이 제조 공정과 같은 첨단산업의 다양한 분야에 쉽게 적용되고 있으며, 그 적용 분야와 시장은 계속 성장하고 있다. 고 진공과 배기 속도의 달성을 위해서, 고속으로 이동하는 격면과 기체분자를 충돌시켜, 기체 분자를 원하는 방향으로 유도하는 작동원리를 가지고 있다. 특히 공기분자의 밀도가 매우 낮은 희박가스 상태에서 고속 회전하는 blade로 공기분자를 쳐내면서 작동됨으로써 날개의 상하 압력차에 의한 공기력보다도 날개의 고속회전이 매우 중요시되고 압력으로는 $10^{-1}Pa$ 이하의 분자 영역에서 그 성능을 최고로 발휘할 수 있다. 이러한 복합 펌프의 주요 장점은 다음과 같다. 1. $10^{-8}\;Pa$($10^{-10}torr$)~10 Pa(1 torr) 까지 넓은 영역에서 배기가 가능하다. 2. 탄화수계의 대하여 높은 압축특성을 가지고 있고, 윤활유를 사용하지 않으므로 얻을 수 있는 진공상태가 고청정하다. (oil free) 3. 정밀 5축제어 자기베어링으로 완전히 부상하여 회전함으로서 마모가 없고 진동이 최소화 하였을 뿐 만 아니라, 또한 운전음도 거의 없다. 4. 설치조건에 제한이 없고 고장이 거의 없다. 본 논문에서는 이러한 복합분자펌프의 개발을 위하여, 상기 연구기관에서 수행된 내용을 소개하고 이으며, 진공펌프 블레이트 로터 회전체를 포함한 구조설계 및 해석결과와 5자유도 자기베어링 시스템을 이용한 기본 구동 결과를 나타내었다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.3
• /
• pp.20-28
• /
• 2007

The easiest way to see the phenomena of compressor surge is to show the static and dynamic operation characteristic on the map. Its operation zone will be restricted by the surge limit and, static and transient process must have some margin for it. Effect of rotor moment of inertia, air/gas volumes and heat transfer are factors to cause the transition from the static line. In case a large volume such as heat exchanger exists in the system it will exert a substantial influence to dynamic characteristics. In the present paper, influence of air volume bled from the compressor exit on transient process is investigated with an example of an auxiliary power unit micro-turbine engine. Turbine mass, pressure ratio, rotation speed, power and moment are calculated based on mass and work conservation. Result from the present study can give guidance to design the control system. A computer program is developed to calculate the dynamic process using the MathCAD commercial software.