• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.7
• /
• pp.653-660
• /
• 2009

A helicopter rotor brake system stops or reduces the speed of the rotor by transforming the kinetic energy into the heat energy. The frictionally generated heat has a considerable effect on the frictional property of material itself and causes the change of the friction coefficient which may affect the breaking time significantly. In this paper, to take into account the effect of change of friction coefficient according to temperature on braking time, thermo-mechanically coupled analysis is carried out by commercial software ABAQUS. Further, simple theoretical equation is derived considering thermo-mechanical behaviors. The predicted braking times both from theoretical and numerical methods are compared and validity of proposed theoretical equation is investigated.

• Proceeding of EDISON Challenge
• /
• 2017.03a
• /
• pp.351-357
• /
• 2017

차량용 브레이크의 성능은 브레이크 디스크 로터의 냉각 성능과 밀접한 관련이 있다. 냉각 성능 향상을 위해 디스크 로터에 구멍을 뚫거나 홈을 깎아내어 열 전달면을 극대화 시키거나 열 전도도가 높은 재료에 대한 연구가 활발하게 진행되고 있다. 본 연구에서는 각각 형상이 다른 디스크 브레이크 시스템의 방열 및 제동 성능, 패드 압력에 대한 응력을 분석하고 온도장 근사 및 열전도 해석 프로그램(Heat_transfer, KAIST, EDISON)과 Elastic-Plastic Analysis SW(CSD_EPLAST, 서울과학기술대학교, EDISON) 및 ABAQUS를 이용해 각각의 냉각 성능 및 응력 분포를 비교 분석한다.

• Composites Research
• /
• v.15 no.1
• /
• pp.41-52
• /
• 2002

This paper presents the thermo-elastic analysis for searching the behavior of carbon/carbon brake system during the braking period and the 3-D stress analysis to find the shape of the brake disk which is safe to the failure. The mechanical properties of the carbon/carbon brake disk were measured for both in-plane and out of plane directions. The mechanical properties were used as the input of the thermo-elastic analysis and 3-dimensional stress analysis for the brake disk. The gap between rotor clip and clip retainer is an important parameter in the loading transfer mechanism of the rotor disk. The change of gap was considered both the mechanical deformation and thermal deformation. Because the rotor clip and clip retainers were not contacted, they were excluded from the analysis model. Rotor disk was modeled by using the cyclic symmetry condition. The contact problems between rotor clip and key drum as well as between rotor disk and rotor were considered. From the results of the 3-D stress analysis, the stress concentration at the key hole of the brake disk was confirmed. The stress distributions were studied thor the variation of the rotation angle of the contact surface and the radius of curvature at the key hole part.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.236-240
• /
• 2005

This paper deals with friction-induced vibration of disc brake system under constact friction coefficient. A linear, finite element model to represent the floating caliper disc brake system is proposed. The complex eigenvalues are used to investigate the dynamic stability and in order to verify simulations which are based on the FEM model, The comparison of experimental and analytical results shows a good agreement and the analysis indicates that mode coupling due to friction force and geometric instability is responsible fur disc brake squeal. And the Front brake system reduced the squeal noise using design of experiment method(DOE). This helped to validate the FEM model and establish confidence in the simulation results. Also they may be useful during real disk brake model.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.3
• /
• pp.325-331
• /
• 2013

In this study, a complex eigenvalue analysis is implemented to verify the unstable mode of a brake system using ABAQUS software. The component participation factors and component modal participation factors are used to analyze the total contributions from each component and each component mode to a particular unstable system mode. This study shows that the 1.4-kHz unstable system mode comes from mode coupling between the 2nd nodal diametric mode and 3rd lateral axial mode (LAM) in the baseline model. A sensitivity analysis with a linking index is performed to prevent the mode coupling of the component modes. This linking index analysis shows the optimum mass loading position to move away the natural frequency of the 3rd LAM, which contributes to the unstable mode. Finally, a complex eigenvalue analysis is implemented with mass loading in the tie bar position, and no unstable system mode is generated in the low-frequency range (below 2 kHz).