• Composites Research
• /
• v.18 no.1
• /
• pp.45-54
• /
• 2005

The delamination in the filament-wound composite flywheel rotor often lowers the performance of the flywheel energy storage system. A conventional ring type hub usually causes tensile stresses on the inner surface of the composite rotor, resulting in lowering the maximum rotational speed of the rotor. In this work, the stress and strain distributions within a hybrid composite rotor were derived from the two-dimensional governing equation with the specified boundary conditions, and an optimum pressure at the inner surface of the rotor was proposed to minimize the strength ratio and maximize the storage energy. A split type hub was introduced to apply the calculated optimum pressure at the inner surface, and a spin test was performed up to 40,000 rpm to demonstrate the performance of the split type hub with radial and circumferential strains measured using a wireless telemetry system. From the analysis and the test, it was found that the split type hub successfully generates a compressive pressure on the inner surface of the rotor, which can enhance the performance of the composite rotor by lowering the strength ratio within the rotor.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1991.04a
• /
• pp.111-116
• /
• 1991

주파수 영역에서 로터의 thickness noise는 블레이드의 여러가지 기하학적인 조건, 즉 블레이드 수, 블레이드의 사잇각, 에어포일의 모양 그리고 반경방향의 블레이드 끝모양에 따라서 해석되어진다. 본 논문은 비 등간격 로터의 기하학적 조건에 따른 음신호의 위상간섭 영향을 고찰하기 위해서 등간격을 이루는 로터에 대해서 해석된 Hanson의 방법을 확장하였다. thickness noise를 6개의 블레이드를 가진 로터에 대하여 15.deg., 30.deg., 45.deg., 비 등간격을 이루는 경우와 각각에 45 tip angle로 sweepback되었을 때 먼 거리의 음향학적 음신호와 그 스펙트럼을 계산하였다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.11
• /
• pp.1133-1143
• /
• 2009

Vibro-acoustic characteristics of a simplified disk-brake rotor containing a narrow radial slot are studied using a semi-analytical procedure. First, modal sound radiations for flexural and radial modes of a generic annular disk having identical key dimension and slot(with free boundaries) are defined using pre-developed analytical solutions based on the modal vibrations from finite element model. The analytical solutions are validated by fully computational methods. Second, sound radiation from a simplified brake rotor simulated using sound radiation solution of the generic disk based on the rotor eigensolutions computed using a finite element code. Predictions by the semi-analytical method matched well numerical calculations using finite element and boundary element method. Finally, sound radiation and vibration characteristics for the example rotor due to a harmonic excitation fixed to the rotor or rotating around the rotor are also obtained.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.373-375
• /
• 2003

상반회전 풍력발전 시스템의 경우 전방에 위치한 로터의 후류 효과를 적절히 반영하여 설계에 이용해야 한다. 본 연구에서는 이러한 로터의 후류효과 및 블레이드의 실속후 모델을 고려하여 30kW급 상반회전시스템의 설계형상에 대한 검토연구를 수행하였다 기본공력이론은 모멘텀 이론과 2차원 준정상 공기력 이론을 통합한 형태를 사용하였다. 로터의 후류영향을 고려하기 위해 축소형 풍차 블레이드 모델에 대한 풍동시험 결과를 적절히 이용하며, 이로부터 보조로터를 지난 후류의 축속도 및 각속도 성분을 결정하였다. 최종적으로 상반회전 시스템의 로터 반경 및 상호 이격거리 등을 고려한 성능해석을 수행하고 이로부터 최적 설계형상에 대한 파라미터 연구결과를 제시하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.4
• /
• pp.315-320
• /
• 2008

This paper describes aerodynamic characteristics for the NREL(National Renewable Energy Laboratory) Phase VI rotor using the Fluent which is a commercial flow analysis tool. Aerodynamic analysis results are compared with experimental results by the NREL/NASA Ames wind tunnel tests. For three velocity cases, computed results are compared with experiment results at five spanwise positions. Computed results represented good agreement with the experimental results at low velocity. Otherwise computed results in suction side represents disagreement with the experimental results at high velocity. When interval between wind turbines is 10 times of rotor diameter, CFD research is performed to calculate the wake effect.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.297-301
• /
• 2007

The blades of supersonic turbines with low aspect ratio are usually designed to have the same cross sectional shape in radial direction. The profile diameter definition of turbines may lead to produce unintended flow passage area variations resulting performance degradation. In this paper, the effects of profile diameter definition on the supersonic impulse turbine performance have been investigated. Computational results of three different profile diameters are compared. It has been found that flow passage area variation can be achieved according to designer's intention when blade profile is defined at rotor tip diameter. Furthermore, the turbine blade profile defined at rotor tip showed better performance than the others.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.9
• /
• pp.3135-3140
• /
• 2010

A 5 kWh composite flywheel rotor was designed and manufactured, and its spin test was performed to monitor strain distribution and burst speed. Strain distribution in radial and circumferential directions of the rotor were measured using a wireless telemetry system based on bluetooth technology for real-time strain measurement. The strains was compared with pre-calculated design values to verify the initial rotor design. We noticed the rotor failed at 19,499 rpm in the spin test, 11 % lower than the predicted burst speed of 22,000 rpm. Failure occurred at the hub which connects the shaft and the composite rotor. The performance of the composite rotor was confirmed in a general sense, and the danger of unexpected failure of composite rotor during high-speed spinning was also demonstrated in this paper. Special attention should be paid to not only composite rotor but also hub when designing a flywheel energy storage system. The telemetry system needs to be further developed, especially enduring the high centrifugal forces, and can be used in a real time monitoring system for the flywheel energy storage system.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.5
• /
• pp.439-446
• /
• 2016

The characteristics of bearingless main rotor of helicopter are investigated through non-rotating tests and rotating tests. The stiffness and natural frequencies of rotor blades, flexbeam, and torque tube which are core components of baearingless rotor are measured to obtain input material properties for rotor analysis. The functional test on ground for assembly of one hub with damper, snubber, and no blade is carried out to check interfaces between components, kinematics of components, and pitch motion ranges under applied loads including centrifugal load. The 4-bladed bearingless rotor with 5.82m of rotor radius is tested on the whirl tower with rotation plane of 9.65m height. The thrust and power are measured to obtain hover performance and the frequencies and dampings of the rotor are obtained by excitation of cyclic pitch by hydraulic actuators.

• Composites Research
• /
• v.15 no.1
• /
• pp.41-52
• /
• 2002

This paper presents the thermo-elastic analysis for searching the behavior of carbon/carbon brake system during the braking period and the 3-D stress analysis to find the shape of the brake disk which is safe to the failure. The mechanical properties of the carbon/carbon brake disk were measured for both in-plane and out of plane directions. The mechanical properties were used as the input of the thermo-elastic analysis and 3-dimensional stress analysis for the brake disk. The gap between rotor clip and clip retainer is an important parameter in the loading transfer mechanism of the rotor disk. The change of gap was considered both the mechanical deformation and thermal deformation. Because the rotor clip and clip retainers were not contacted, they were excluded from the analysis model. Rotor disk was modeled by using the cyclic symmetry condition. The contact problems between rotor clip and key drum as well as between rotor disk and rotor were considered. From the results of the 3-D stress analysis, the stress concentration at the key hole of the brake disk was confirmed. The stress distributions were studied thor the variation of the rotation angle of the contact surface and the radius of curvature at the key hole part.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.8
• /
• pp.598-604
• /
• 2003

In this paper a general solution method is presented to obtain the unbalance response orbit from the finite element based equations of motion of a gear-coupled two-shaft rotor-bearing system, whose shafts rotate at their different speeds from each other. Particularly, are proposed analytical solutions of the maximum and minimum radii of the orbit. The method has been applied to analyze the unbalance response of a 800 refrigeration-ton turbo-chiller rotor-bearing system having a bull-pinion speed increasing gear. Bumps in the unbalance response of the driven high speed compressor rotor system have been observed at the first torsional natural frequency due to the coupling effect of lateral and torsional dynamics. Further, the proposed analytical solutions have agreed well with those obtained by a full numerical approach. The proposed analytical solutions can be generally applied to obtain the maximum and minimum radii of the unbalance response orbits of dual-shaft rotor-bearing systems coupled by bearings as well.