• Journal of Biosystems Engineering
• /
• v.22 no.4
• /
• pp.391-400
• /
• 1997

Using the soil bin systems, this study was carried out to investigate the tilling load characteristic for the three kinds of Japanese rotary blade and the possibility of common use for power tiller and tractor rotary. The results obtained from the study are summarized as follows : 1. At all tested soils. the average and maximum tilling torque of all tested blades increased as the tillage pitch did. 2. The torque requirements of newly designed and produced blade was less than that of blade which has been used on power tiller and tractor rotary. 3. The maximum tilling torque of new ONE were decreased 7%, 10~11％, 27% in comparing with another blades at clay loam, loam and sandy loam, respectively. 4. According to observation of the extent of soil adhesion on blade and the contact aspect of blade, new ONE is the most excellent of all tested rotary blades and till smoothly not to compress the untilled soil. From the results of this study. the newly developed blade(new ONE) proved to be good tilling load performance and had a conclusion that it is possible to use it on power tiller and tractor rotary in common.

• The KSFM Journal of Fluid Machinery
• /
• v.18 no.3
• /
• pp.12-19
• /
• 2015

As a means of improving cycle performance of a R410A air-conditioning system, a combined structure of compressor and expander was introduced. A vane rotary type expander was designed to share a common shaft with twin type rolling piston rotary compressor in a housing. Numerical simulation on the performance of the combined compressor and expander was carried out. At ARI condition, the volumetric and total efficiencies of the designed vane expander were 69.37% and 30.23%, respectively. With the application of this expander, the compressor input was reduced by 3.91%, and the cooling capacity was increased by 3.98%. As a result, COP of the air-conditioning system was improved by 8.2%. As the pressure difference between the condenser and the evaporator becomes large, COP improvement increases unless the mass flow rate in the expander exceeds that in the compressor.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.171-176
• /
• 2008

As one way of design optimization of two-stage two-cylinder rotary compressor used for R410A heat pump application, displacement volume ratio, being defined by the ratio of the second stage cylinder volume to that of the first stage, has been varied and its effect on the compressor performance has been investigated by a computer simulation program. For simplicity, only the cylinder height of the second stage was varied to change the volume ratio. With increasing the volume ratio in the range of VR=$0.55{\sim}0.9$, volumetric efficiency increased monotonically, but adiabatic efficiency showed a maximum at around VR=0.6. Mechanical efficiency was little influenced by the volumetric ratio. As a consequence, maximum improvement of the compressor performance was found at around VR=0.7. Compared to a one-stage two-cylinder rotary compressor with about the same cooling capacity, COP improvement was about 6.96%.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.6
• /
• pp.497-504
• /
• 2001

A study to improve the accuracy of a map-based compressor model with experiment was performed. Corrections on the effects of suction gas superheat and heat leakage from a compressor shell are required to apply the compressor amp model based on the empirical performance data(map) of compressor manufacturers to the actual system. So experiments to assess the effects of superheat and hat leakage were performed and the corrected equations were made. Compressors and refrigerant used in the experiment were the high pressure type rotary compressor and R-22, experiments were performed by compressor calorimeter. From the experiment, a volumetric efficiency correction factor$(F_ν)$ showed the value of 0.77, slightly higher than 0.75 proposed by Dabiri and Rice for low pressure type reciprocating compressor, and the heat leakage from the compressor shell turned out to be a factor that influenced the discharged mass flow rate. The relation between heat leakage of compressor shell and the variation of discharged mass flow rate from compressor was considered in compressor map modeling as an empirical function. With this function, the prediction accuracy of compressor model in system conditions was improved.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.23 no.8
• /
• pp.549-555
• /
• 2011

For a $CO_2$ one-stage twin rotary compressor, a T-shaped suction port was used to effectively supply the suction gas stream into two individual suction chambers of the twin cylinders. Suction gas pulsations were observed in the pressure sensor signals and these were simulated by using the acoustic modeling of Helmholz resonators in parallel. The module of acoustic modeling was combined to a computer simulation program for the compressor performance. Validation of the simulation program has been carried out for a bench model compressor in a compressor calorimeter. Cooling capacity and the compressor input power were reasonably well compared between the simulation and the calorimeter test. Particularly, good agreement on P-V diagram between the simulation and the test was obtained.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.21 no.1
• /
• pp.55-62
• /
• 2009

Relatively low cycle performance of a conventional $CO_2$ system is partly due to significant increase in friction loss in the expansion process, since the pressure drop across the expansion device is considerably large compared to a conventional refrigeration cycle. To recover friction loss and increase refrigeration effect by providing isentropic expansion, a rotary vane type expander has been designed. Performance of the designed expander has been investigated by numerical simulation. With the pressure condition of 9 MPa/4.5 MPa and inlet temperature of $35^{\circ}C$, volumetric, isentropic, and mechanical efficiencies of the expander are calculated to be 58.1%, 101.1%, and 78.8%, respectively, resulting in total expander efficiency of 46.3%. With this expander, COP of a $CO_2$ refrigeration cycle is estimated to be improved by about 14%.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.8-8
• /
• 2017

본 연구는 로타리 작업에 따른 105마력급 농업용 트랙터의 소요동력을 분석하기 위하여 수행되었다. 소요동력 측정 시스템은 차축 토크미터, PTO 토크미터, 주/보조 유압센서, 데이터 수집장치를 이용하여 구성하였다. 시험에 사용된 트랙터는 동양물산 105 HP급 트랙터 (S07, TYM, Korea)이며, 작업기는 로타베이터 (SW 230GL, Sungwoo Industrial Co. Ltd, Korea)를 사용하였다. 포장시험은 전라북도 부안군에 죽림길에 위치한 $4,000m^2$ ($100m{\times}40m$) 크기의 경작지 2곳에서 수행하였다. 포장시험 시 작업 단수는 주행단수 L3단 (2.38 km/h)에서 PTO 단수 1단 (540 rpm)과 2단 (750 rpm)으로 설정하였고, 로타리 작업 시 경심은 13 cm 조건에서 실시하였다. 트랙터 작업은 동양물산의 성능시험 업무를 맡고 있는 숙련된 작업자가 숙달된 방법으로 수행하였다. 포장시험지의 토양환경은 임의의 15곳에서 채취한 시료를 이용하여 토성, 함수율, 원추 관입지수에 대하여 미국 농무부 (USDA)법을 기준으로 분석하였다. 토양환경 분석 결과 토성은 Sandy loam (사양토), 평균 함수율은 35.15%, 평균 원추관입지수는 1,562 kPa로 나타났다. PTO 1단 작업 시 트랙터의 평균 소요동력은 차축, PTO, 주 유압, 보조 유압에 대하여 각각 1.8, 54.0, 1.3, 그리고 1.1 hp로 나타났다. PTO 2단 작업 시 트랙터의 평균 소요동력은 차축, PTO, 주 유압, 보조 유압에 대하여 각각 1.2, 79.4, 1.2, 그리고 1.0 hp로 나타났다. PTO 1단 작업 시 소요동력의 합은 58.2 hp로, 정격 마력 (105 hp) 대비 55.43 % 사용한 것으로 나타났으며, PTO 2단 작업 시 소요동력의 합은 82.8 hp로, 정격 마력 대비 78.85% 사용한 것으로 나타났다. PTO 1단 대비 2단에서는 PTO를 제외한 차축, 주 유압, 보조 유압의 소요동력이 감소하였으나, PTO에서 약 1.47배로 크게 증가하여 전체적으로 소요동력이 증가한 것으로 나타났다. 향후 다양한 작업기 및 작업 단수에 따른 소요동력을 분석하여 농업용 트랙터의 모든 부하 조건에 대한 데이터베이스 구축에 관한 연구를 수행할 예정이다.

• Korean Journal of Soil Science and Fertilizer
• /
• v.18 no.2
• /
• pp.189-193
• /
• 1985

A field experiment was conducted to find out the effects of tillage methods on the changes of soil physical properties and rice yields. Silty clay loam soil was treated with six kinds of different tillage methods, cultivator plow-rotary, rotary, tractor deep plow-rotary, subsoiling-rotary, chisel plow-rotary and no-tillage, and Jinju variety of rice was cultivated. The results were summarized as follows; 1. Working efficiency was highest at chisel plow and the efficiencies were decreased with the order of deep plow, subsoiling, rotary, and cultivator plow. 2. Deep plow and chisel plow were considered as the useful treatments of physical properties to 20 cm depth soil and subsoiling was effective to 40 cm depth soil. 3. Rice yields were decreased 4% by rotary and 11% by no-tillage compare to cultivator plow-rotary but the yields were increased 5% by deep plow, 4% by subsoiling and 3% by chisel plow. As the results of all the data, welting efficiency, soil physical properties and rice yields, tractor deep plow was recommendable tillage method for rice paddy soils.

• Korean Journal of Weed Science
• /
• v.15 no.1
• /
• pp.39-45
• /
• 1995

This experiment was carried out at Yeongnam Crop Experiment Station since 1992 to obtain basic information on ecology of weeds and weedy rice in direct-seeded rice fields. Annual grass weeds of Echinochloa sp., Leptochloa sp., Digitaria sp. and Setaria sp.(C4 plant) and weedy rice(C3 plant) were important species in direct seeded rice compared to transplanted rice field. Period of seedling emergence of barnyard grass was varied from 8 days to 20 days depending on seeding date while it was shorter 4 to 6 days than rice. Weed occurrence and the degree of yield loss were varied by cultivation method. In direct seeding method weeds increased 2 to 3 times compared to manual transplanting. The greatest yield loss was recorded in direct seeding(40 to 100%) followed by mechanical transplanting(25 to 35%) and hand transplanting(10 to 20%), in order. Double cropping of rice-barley was reduced weeds about 30% than rice single crop due to alleopathic effect of barley residue or stubble. Weedy rice(red rice) occurrence was closely related with seeding date and tillage methods. Early seeding and reduced tillage enhanced the growth of weedy rice.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1995.06b
• /
• pp.28-37
• /
• 1995

To protect the ozone layer depeletion the CFC (chlorofluorocarbon). HCFC(hydrochlorofluorocarbon) refrigerants will be replaced with HFCs (hydro-fluorocarbon) as an alternative refrigerant. In recent years a good deal of effort has been made to develop new compressors which are compatible to the new referigent. This paper focused on developing accelerated screening test for predicting tribological characteristics of the rotary compressor in atmosphere of R407C as an alternative refrigerant with polyolester lubricant. Falex wear test machine with high pressure chamber has been used to simulate friction and wear behavior of the common contact geometries found in rotary compressors.