• Proceedings of the Korean Geotechical Society Conference
• /
• 1996.12a
• /
• pp.89-100
• /
• 1996

• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.5
• /
• pp.23-30
• /
• 2007

The effectiveness of a pogo suppression device (PSD) on the response of piping system simulating the propellant supply lines of the rocket engines was investigated experimentally by other researchers. In this study, the simplified analytical model was made, and the key parameters which are difficult to derive theoretically were identified in combination with the previous experimental work. In other words, the flow transient equations for a PSD system and the key parameters used to decide the instability of the system from the linearized transfer function including inertance, compliance, and resistance were derived. From the analysis, the values of key parameters could be determined from the experimental results.

• Proceedings of the Acoustical Society of Korea Conference
• /
• autumn
• /
• pp.375-378
• /
• 2001

천공 요소는 유체 기계의 흡기계나 배기계의 소음기에 널리 사용되고 있으며, 스치는 유동 (grazing flow)과 통과하는 유동 (cross flow)을 접하게 된다. 천공 요소의 임피던스는 소음기의 음향학적인 특성에 영향을 미치게 된다 본 연구에서는 유동이 임피던스에 미치는 영향을 고려하기 위하여, 실험을 통하여 얻은 임피던스 값을 유동 레지스턴스 (flow resistance)와 종단 보정 비 (end correction ratio)로 나타내고, 스트롤 수 (Strouhal number)로 무차원 화하여 분석하였다 이를 난류를 고려하여 제안된 선행 임피던스 모델들과 비교하여 난류가 미치는 영향을 분석하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.5
• /
• pp.516-522
• /
• 2020

Water trees can cause considerable damage to the performance of underground cables. Theymay formwithin the dielectric used in buried or water-immersed high voltage cables. They grow in a bush-like or tree-like form, often taking decades before causing damage to a cable's performance. They are usually found on very old underground cables, often in an inaccessible place. It is costly and time-consuming to detect watertrees in underground cables. Tree detection technology, including mathematical modeling,can reduce the maintenance cost and time necessary for detecting these trees.To simulate detection of water trees in this study, a mathematical model ofan XLPE cable and a water tree were developed. The complex water tree structure was simplified, based on two identified patterns of aventedtree. A Matlab simulation was performed to calculate and analyze the capacitance and resistance of a cable insulation layer,based on growth of a watertree. Capacitance size increased about 0.025×10^-13[Farads/mm] compared to normal when the tree area of the cable was advanced to 95% of the insulation layer. The resistance value decreased by about 0.5×10¹⁶[ohm/m]. These changesand changesshowninaBurkes paper physical modeling simulation are similar.The value of mathematical modeling for detecting water trees and damage to underground cables has been demonstrated.

• Geotechnical Engineering
• /
• v.13 no.2
• /
• pp.39-54
• /
• 1997

Laboratory testings were carried out on plastic board drains (PBDs) using large scale test apparatus to evaluate the physical properties and the drainage performance. The test results reveal that the domestic products of PBDs are well compared with the foreign prod acts as far as the quality and drainage performance are concerned. It has also been confirmed that the discharge capacity decreases with time in such a way that the air bubbles are entrapped inside kinky PBDs and these air bubbles block the water flow through PBDs. It has been found that the vacuum pressure iseffectively applicable to recover the discharge capacity affected by the entrapped air bubbles.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.10
• /
• pp.983-990
• /
• 2010

Reduction of acoustic loads of space launch vehicles can be achieved by acoustic absorbers satisfying strict cleanness requirements. This limited the use of general porous materials and requires non-porous sound absorbers. Micro-perforated panel absorbers(MPPA) is one of promising sound absorbers satisfying the cleanness requirement for launch vehicles. However, its applicability was limited to low sound pressure levels according to the acoustic impedance model of micro-perforated panels. In this paper the applicability of micro-perforated panel absorbers at high incident sound pressure was investigated in experimental ways. The absorption characteristics of a micro-perforated panel absorber was simulated according to its design variables, e.g., minute hole diameters and aperture ratios. It was shown that optimal design can be readily done by using proposed design charts. Experiments were conducted to measure acoustic properties of the designed micro-perforated panel absorbers. The results showed that acoustic resistance increases rapidly as incident sound pressure level does but change of acoustic reactance can be neglected in a practical point of view. This caused the decrease of peak value of absorption coefficient at high incident sound pressure level, but the amount of reduction can be accepted in practice. The major advantage of the micro-perforated panel absorber(wide absorption bandwidth) was still kept at high sound pressure level.

• Journal of the Korea Institute of Building Construction
• /
• v.23 no.6
• /
• pp.727-738
• /
• 2023

In concrete, the interface between the aggregate and cement paste is often the most critical factor in determining strength, representing the weakest zone. Lightweight aggregate, produced through expansion and firing of raw materials, features numerous surface pores and benefits from low density; however, its overall aggregate strength is compromised. Within concrete, diminished aggregate strength can lead to aggregate fracture. When applying lightweight aggregate to concrete, the interface strength becomes critical due to the potential for aggregate fracture. This study involved coating the surface of the aggregate with blast furnace slag fine powder to enhance the interfacial strength of lightweight aggregate. The impedance of test specimens was measured to analyze interface changes resulting from this surface modification. Experimental results revealed a 4% increase in compressive strength following the coating of the lightweight aggregate surface, accompanied by an increase in resistance values within the impedance measurements corresponding with strength enhancement.