• Korean Journal of Optics and Photonics
• /
• v.14 no.1
• /
• pp.92-96
• /
• 2003

Dielectric apertures in vertical cavity laser have been used for improved device performance. Numerical analysis is used to estimate the optical losses as the aperture diameter is reduced. The optical losses depend on the aperture size, thickness and location. The optical loss strongly depend on the aperture size and thickness when the aperture size is similar or smaller than the emitted wavelength. The optical loss is negligible and not depend on the aperture thickness when the aperture size is larger than 5 times emitted wavelength.

• Proceedings of the KIEE Conference
• /
• 2002.11a
• /
• pp.130-133
• /
• 2002

엑시머 레이저를 이용한 저온($450^{\circ}C$ 이하) 다결정 실리콘 박막 트랜지스터 제작 시, 소오스/드레인 이온 주입에 의한 실리콘 박막의 격자 손상은 엑시머 레이저 어닐링(Excimer Laser Annealing; ELA) 방법으로 치유한다. 그러나 게이트 전극 모서리에서의 레이저광 회절 현상으로 인해 소오스/드레인 접합부에 도달하는 레이저 에너지 밀도가 감소하여 다량의 결정 결함이 치유되지 못한 채 남게 된다. 이러한 결정 결함은 박막 트랜지스터의 전계 효과 이동도를 저하시키는 요인이 된다. 새롭게 제안한 사선 입사 엑시머 레이저 어닐링(Oblique Incidence Excimer Laser Annealing; OI-ELA) 방법으로 소오스/드레인 접합부의 결정 결함을 제거하고 다결정 박막 트랜지스터의 특성을 향상시켰다.

• Korean Journal of Optics and Photonics
• /
• v.7 no.3
• /
• pp.238-243
• /
• 1996

We have developed XeCl laser pumped double-resonator Dye laser and two-stage amplifier system, and generated simultaneously of alternatively two wavelengths suitable in DIAL system. The developed double-resonator is composed of 1st and 2nd diffraction orders on light incidence angle in grazing-incidence grating method with 1200 g/mm. We have obtained spectral linewidth below 10 pm and the total efficiency dependent on pump energy over 6%. The tuning ranges dependent on 1st and 2nd diffraction orders are 434~470 nm and 436~468 nm, respectively. The amplification gain and rine-450 dye laser by using the double-resonator laser system and measured the distribution of $NO_2$ concentration over Suwon as the result of transmission of laser output of 6 mJ in this DIAL system. Consequently, we have confirmed that the developed dye laser system is very useful as the tunable source for DIAL.

• Korean Journal of Optics and Photonics
• /
• v.10 no.5
• /
• pp.391-395
• /
• 1999

We present the measurement of the diffraction efficiency and response time of the photorefractive grating recorded in $LiNbO_3$ photorefractive crystal doped with 4%-mole MgO. Two laser sources were used in the experiments; frequency-doubled Q-switched Nd:YAG laser ($\lambda$=532 nm) and cw Ar-ion laser ($\lambda$=514.5 nm). The same optical geometry was also used in both experiments in order to maintain the experimental consistency. Using the two-wave mixing scheme in both experiments we measured the maximum diffraction efficiency in the range of beam intensity of 1.6~100 W/ $\textrm{cm}^2$, and the response times for both cases of recording and erasing. Two sets of results obtained from the experiments are compared and analyzed.

• Korean Journal of Optics and Photonics
• /
• v.8 no.2
• /
• pp.107-110
• /
• 1997

We generated a diffraction free beam from Nd:YAG laser with an NBUR (negative branch unstable ring) resonator. The field inside the resonator had a plane wavefront and a homogeneous intensity distribution and the output beam through a scraper mirror of an annular type was used as a source. The outpur beam had an inner radius of 2.5 mm and an outer radius of 5 mm. In this experiment, we used a Fourier transformation lens with the focal length of 5 m to observe the far-field pattern. The lens was placed at a distance of the focal length from the scraper mirror and we found that the beam did not show any noticable diffraction over the distance of 13 m from the lens.

• Korean Journal of Optics and Photonics
• /
• v.6 no.4
• /
• pp.331-336
• /
• 1995

The steady-state absorption saturation of the photodarkend SDG was investigated. The absorption saturation intensity was observed to increase for the photodarkened sample. The diffraction efficiency of the permanent grating due to photodarkening was also measured using the backward DFWM technique. For the low backward pump intensity, the diffraction efficiency was proportional to the intensity of the pump beam. The origin of increasing diffraction efficiency is attributed to the difference in absorption between the permanent gratings created by photodarkening. ening.

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2006.06a
• /
• pp.97-100
• /
• 2006

Picosecond (ps) laser micro-machining has emerged as an attractive method of fabricating high-precision microstructures, especially in metals. In this paper, a metallic mold for diffraction gratings is fabricated with a mode-locked 12 ps $Nd:YVO_4$ laser. Laser pulses with a wavelength of 355nm are irradiated on the surface of NOK 80, a mold material, to generate line patterns. In order to minimize the line width, laser power is set just above the ablation threshold of NOK 80. Results show that the spectrum from the fabricated mold is good enough for some industrial application.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.7
• /
• pp.80-91
• /
• 1999

We present various optimal grating structures which give the low threshold gain, good modulation characteristics, small effective linewidth enhancement factor, and large fabrication tolerance in complex-coupled MQW DFB lasers with absorptive gratings. To obtain these, we calculate the complex coupling coefficients using the extended additional layer method and the threshold gain including the modal loss in the absorptive grating region for rectangular and trapezoidal gratings. Based on the comparison of the results for various possible absorptive grating structures, the design guidelines are presented to obtain the low threshold gain or large fabrication tolerance. Among the grating structures studied, the double grating structure consisting of the absorptive grating on the index grating has the largest fabrication tolerance for the threshold gain and the coupling strength. The fabrication tolerance for the coupling ratio is very large for all the grating structures studied.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.9
• /
• pp.624-633
• /
• 2001

Influence of the grating half-period fluctuation on the normalized coupling coefficient has been studied by an effective index transfer matrix method in quarter wavelength shifted(QWS) DFB lasers. The laser facets are assumed to be perfectly antireflection coated, and the period fluctuation is modeled by two correlated Gaussian random variables. In the presence of the random fluctuation in the grating period, effective normalized coupling coefficient is reduced because the in-phase feedback strength Is weakened. We have shown that the normalized coupling coefficient determined from the side mode spacing is less than the effective coupling coefficient, and the normalized coupling coefficient determined from the mode spacing or spontaneous emission spectrum does not properly represent the feedback strength of the grating.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.10
• /
• pp.845-850
• /
• 2016

A direct laser lithography system is widely used to fabricate various types of DOEs (Diffractive Optical Elements) including lenses made as CGH (Computer Generated Hologram). However, a parametric study that uniformly and precisely fabricates the diffractive patterns on a large area (up to $200mm{\times}200mm$) has not yet been reported. In this paper, four parameters (Focal Position Error, Intensity Variation of the Lithographic Beam, Patterning Speed, and Etching Time) were considered for stabilization of the direct laser lithography system, and the experimental results were presented.