• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.333-338
• /
• 2002

자기베어링의 회전정밀도에 영향을 미치는 인자로 PWM 전력증폭기, 위치 센서 등과 같은 자기베어링 구성 장치의 동특성 및 정밀도, 시스템의 정확한 모델링, 제어기법, 런아웃 등이 있다. 본 연구에서는 능동 자기베어링을 제어하기 위해 자기베어링의 PWM 전력증폭기와 회전축을 모델링하고 이를 바탕으로 능동 자기베어링 제어를 위한 PID 제어기를 구성하였으며, 변위 센서의 부착위치 및 회전축의 진원도의 영향으로 발생하는 주기적인 런아웃 요소를 첨가하여 런아웃의 영향을 확인하였으며, 런아웃 (Runout)에 의해 발생하는 에러(Error)를 효과적으로 제어하여 자기베어링의 제어 정밀도를 향상시키기 위한 방법으로 기본적인 PID 제어기에 최소평균자승(Least Mean Square, LMS) 알고리즘을 적용한 적응 피드포워드 제어기를 구성하여 자기베어링의 능동 제어에서 발생하는 주기적인 런아웃을 효과적으로 제어할 수 있음을 MATLAB을 통한 시뮬레이션을 통해 확인하였다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.579-585
• /
• 2003

This paper investigates the whirling, tilting and flying motion of a HDD spindle system supported by FDB experimentally. Experimental setup is built to measure the flying, whirling and tilting motion of the HDD spindle system, and three capacitance probes fixed on the xyz-micrometers measure the displacement of a HDD spindle system in the xyz-directions. This research shows that the tilting and whirling motion is mostly dependent on the centrifugal force and the gyroscopic moment due to the unbalanced mass of a HDD spindle. It also shows that the rotating HDD spindle starts to float to the equilibrium position in the z-direction until the weight of the rotating spindle is equal to the supporting pressure generated in the upper and lower thrust bearing.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.3
• /
• pp.22-29
• /
• 2004

Runout causes severe differences among cutting force waveforms due to changes of rotational radii. Thus a runout model must be included in a cutting force model to simulate cutting force accurately. In this paper, a runout modeling method and a measurement method using a dialgauge were developed, which were easy to apply. To calculate runout parameters, a computer program algorithm which obtained runout parameters from measurement values was developed. Cutting force waveforms simulated from cutting force model considering runout effect and measured from experiments had good agreements for their wave size and order.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.5
• /
• pp.65-71
• /
• 1998

This paper presents in-process compensation methodology to eliminate cutter runout and improve machined surface quality. The cutter runout compensation system consists of the micro-positioning mechanism with the PZT (piezo-electric translator) which is embeded in the sliding table to manipulate the radial depth of cut in real time. For the implementation of cutter runout compensation methodology. cutting force adaptive control was proposed in the angle domain based upon PI (proportional-integral) control strategy to eliminate chip-load change in end milling process. Micro-positioning control due to adaptive acuation force response improves the machined surface quality by compensation or elimination of cutter runout induced cutting force variation. This results will provide lots of information to build-up the precision machining technology.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.10
• /
• pp.1159-1165
• /
• 2011

The recording density of HDD is increasing in ratio of 100% each year. Because the increasing of recording density requires the feature of high rotation, fixation and low-noise, fluid hydrodynamic bearing(FDB) has been paid attention to overcome a limitation in ball bearing. Most of researches related to improving performance of FDB have been studied in Japan which has 80% more market share of HDD spindle motor assembly. Main subject of studies are about for the design of the groove shape, manufacturing process of fluid dynamic bearing, performance evaluation and measurement. In HDD, non-repeatable runout(NRRO) is most important parameter which determines the performance of HDD spindle system because NRRO is unpredictable that cannot be compensated in head/slider servo system. In this study, performance evaluation system can measure dynamic behaviors were designed and methodology for calculating imbalance, RRO, and NRRO were proposed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.3
• /
• pp.41-47
• /
• 2005

This paper deals with a squeal noise in a brake system. It has been proved that the squeal noise is influenced by the angular misalignment of a disk, disk run-out, with the previously experimental study. In this study, a cause of the noise is examined by using FE analysis program(SAMCEF) and numerical analyses with a derived analytical equation of the disk based on the experimental results. The FE analyses and numerical results show that the squeal noise is due to the disk run-out as the experimental results and the frequency component of the noise equals to that of a disk's bending mode arising from the Hopf bifurcation.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.595-600
• /
• 2004

This paper deals with a cause analysis of a squeal noise in a brake system. It has been proved that the squeal noise is influenced by the angular misalignment of a disk, disk run-out, with the previously experimental study. In this study, a cause of the noise is examined by using FE analysis program(SAMCEF) and numerical analyses with a derived analytical equation of the disk based on the experimental results. The FE analyses and numerical results show that the squeal noise is due to the disk run-out as the experimental results and the frequency component of the noise equals to that of a disk's bending mode arising from the Hopf bifurcation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1555-1558
• /
• 2005

In this study, we measured cylindricity and Runout of the air bearing spindle, and tested PCB(printed circuit boards) drilling with 0.4mm micro drill at 90,000rpm and 110,000rpm in order to obtain drilling hole error. Results are as follows; The air bearing spindle's Runout was not so high within $10\mu{m}$ from 20,000rpm to 80,000rpm but it grew after 80,000rpm. Drilling hole size error was 9% at 80,000rpm and 12% at 110,000rpm because of spindle's Run out. Drilled hole shape falsified more 110,000rpm than 90,000rpm.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1248-1252
• /
• 2005

Mold-manufacturing process consists of machining and finishing process that are strongly related in each other. But there are few studies about mold-manufacturing process to control those two processes simultaneously. Especially, runout distorts the machined surface from expected so it changes the finishing process and mold-manufacturing time. In this work, basic analyses and experiments were carried out to study RVAS variation according to runout in HSM. To perform those analyses, firstly surface generation analysis was done including runout in ball end milling and then the RVAS that could relate machining and finishing process was proposed. And the optimal finishing process in HSM according to RVAS was also proposed. Through experiment runout occurrence and above analyses were verified.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.223-228
• /
• 2006

Brake judder of an automotive vehicle is defined as an abnormal vibration of low frequency during braking. Under the assumption that judder occurs due to disc run-out and is a resonance phenomenon with a specific parts of the automobile, computational simulations using SAMCEF software were performed in this paper. The results show that the stabilizer of the car is a possible part which makes the judder vibration due to resonance. And initial braking velocity, the magnitude of run-out, and the friction coefficient between disk and pad are the influential factors to the brake judder.