• Journal of the korean Society of Automotive Engineers
• /
• v.18 no.2
• /
• pp.72-92
• /
• 1996

식물유, 어유 및 축산 폐기물을 포함한 동식물성 기름은 어느 연료든지 기관의 연료로서 사용 가능하지만, 이들 연료는 점도가 높고, 저휘발성이어서 착화지연기간동안에 가연성혼합기 생성이 어려워 저 NOx이며, 정숙한 운전이 사능할 뿐 아니라 경유정도의 열소비율 및 배기 매연농도로 디젤기관의 대체 연료로서의 충분한 가능성이 있는 연료임을 확인하였다. 그러나, 고점도에 의한 분무 특성의 악화에 기인한 분무입자의 증대로 미연소분에 의한 carbon deposit 및 piston ring stick 등이 문제점으로 지적되었다. 그러나, 이같은 문제점의 해결책으로 경질유와의 혼합, 에스테르 변환 및 연료의 가열등 여러 해결책을 제시하였고, 배기가스분석결과도 양호함을 확인하였다. 이같은 biomass 연료 일종인 식물유가 아무런 변화없이 이용되기 위해서는 고과급화, 단열 및 연소실의 적절한 설계가 필요할 것으로 생각된다. 따라서, 현재의 실황을 생각한다면 기존기관을 특별하게 개조함이 없이 사용을 전제로 할 때 식물유의 이용은 local 에너지로서, 생산, 전환 또는 이용기술의 개발과 동시에 화석에너지의 보충적인 에너지로 고려하는 것이 유효할 것으로 생각된다.

• Journal of ILASS-Korea
• /
• v.22 no.4
• /
• pp.203-209
• /
• 2017

The International maritime organization(IMO), in an effort to slow down the global warming, proposes reduction in ship's speed as a way to lower the rate emissions from ships. In addition, since ship's fuel cost have been increased, the shipping volumes, fuel-saving technology are being required urgently. Therefore, in this present study, a method of reducing the fuel cost that can improve the performance of the diesel engine was tried by introducing a predetermined amount (0.1~0.3% of the mass amount of fuel used) of hydrogen fuel additive. The experimental conditions of the test engine were 1500rpm and torque BMEP-10b ar. The engine performances (power output, fuel consumption rate, p-max, exhaust temperature) were compared before and after addition of hydrogen fuel additives. This experimental study confirmed reducing at least 2% fuel consumption and 2.19% NOx emission.

• Journal of Power System Engineering
• /
• v.14 no.6
• /
• pp.5-12
• /
• 2010

In this study, an analysis of evaporative diesel spray and an usefulness of a general-purpose program, ANSYS CFX release 11.0, are investigated through the comparison and investigation of the experimental results carried out under an evaporative field, in which there is phase transition, by an exciplex fluorescence method and the results analyzed by the CFX program. The diesel fuel called n-Tridecane, $C_{13}H_{28}$, is injected from a single-hole nozzle (l/d=1.0mm/0.2mm) into a constant volume chamber under a high temperature and pressure. In the same condition as the experimental condition, the analysis was carried out. Both results of the spray tip penetration were almost coincident at each time. The results have validated the usefulness of this analysis. As a result, if the ambient pressure is high, the spray tip penetration will be shortened and move toward the nozzle exit.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.3 s.234
• /
• pp.402-408
• /
• 2005

The instantaneous temperature behaviors on impinging plate in case of ultra high pressure have been measured and analyzed by using the instantaneous temperature probe and ultra high pressure injection equipment. The temperature drop was largest at P1 which is center of impinging spray and decreased with propagation of spray to the radius direction. The temperature drop was bigger in case of higher temperature of impinging plate. The temperature drop decreased with increase of injection pressure. But decreasing rate of temperature drop was slight over 2,500 bars. Therefore, it was predicted that the fuel evaporation versus the increase of injection pressure was maximum at around 2,500 bars.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.6
• /
• pp.23-29
• /
• 2004

This work was conducted to figure out the atomization characteristics of three types of bio-diesel fuels using a common-rail injection system. The process of spray development was visualized by using a spray visualization system composed of a Nd:YAG laser and an ICCD camera, The spray tip penetrations were analyzed based on the frozen images from the spray visualization system. On the other hand, the microscopic atomization characteristics such as the distributions of SMD and axial mean velocity were measured by using a phase Doppler particle analyzer system, It is revealed that the sprays of the bio-diesel fuels have larger SMD than that of diesel fuel mainly due to high viscosity of bio-diesel. Different characteristics of bio-diesel fuels were also measured in spray tip penetrations according to the fuels and mixing ration.

• Journal of ILASS-Korea
• /
• v.22 no.1
• /
• pp.22-28
• /
• 2017

In this study, the effects of intake valve closing timing by using Cam-in-Cam system on combustion and emission characteristics for diesel engine were investigated under GT-POWER simulation environment. As a result, it was found that volumetric efficiency and effective compression ratio were decreased as the intake valve closing(IVC) timing is retarded due to its backflow effect. Also, we found that in-cylinder pressure, heat release rate and NOx emission were decreased as IVC timing was retarded. These show that the LIVC(late intake valve closing) can be effective to control AFR and mixing rate in diffusion combustion of diesel engine.

• Journal of ILASS-Korea
• /
• v.23 no.2
• /
• pp.90-95
• /
• 2018

The goal of this study is to experimentally observe the autoignition phenomena of a diesel/1-butanol mixture droplet in ambient pressure and $700^{\circ}C$ condition. A volume ratio of 1-butanol in the fuel was set to 25, 50 and 75%. A single droplet was installed at the tip of fine thermocouple, and the electric furnace dropped down to make elevated temperature condition. Droplet behavior during the experiment could be divided into 3 stages including droplet heating, puffing and autoignition/combustion. Puffing process intensively observed for the case of 1-butanol volume ratio of 25 and 50%, but did not occur at 75%. Increase of 1-butanol volume ratio hindered rise of the droplet temperature and delayed ignition. In addition, puffing process also affected on autoignition, so the ignition delay of 1-butanol volume ratio of 50% was became longer than that of 75% case.

• Journal of ILASS-Korea
• /
• v.26 no.3
• /
• pp.142-148
• /
• 2021

The objective of this study is to analyze the basic flame behavior characteristics using the single fuel droplet combustion of diesel, palm-based biodiesel, and canola-based biodiesel. The results were compared and analyzed through the post processed image, which was applied the threshold level for removing noise in the raw image. The raw image was taken by a high-speed camera during the entire combustion process. At the same time, the maximum flame length, which was measured by the application code of the MATLAB program, the ignition delay, and the combustion period were compared and analyzed.

• Journal of ILASS-Korea
• /
• v.27 no.2
• /
• pp.101-108
• /
• 2022

Performance and emissions with different diesel injection methods were analyzed in a natural gas-diesel, dual-fuel engine under low-load conditions. Natural gas was supplied to intake port during the intake stoke to form a natural gas-air premixed mixture for all methods. Diesel was injected directly into the cylinder during the compression stroke in three ways: early injections, late injections, and a combination of early and late injections. The early injections had the highest thermal efficiency among the three methods owing to its highest combustion efficiency. The wide dispersion of diesel before the combustion initiation also allowed superior emissions characteristics.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.1
• /
• pp.17-24
• /
• 2005

The characteristics of diesel spray have effect on the engine Performance such as power. fuel consumption and emissions. Therefore, This study was Performed to investigate the effect of various injection parameters. In this study. the experiment is performed by using the high temperature and high pressure chamber. Spray behaviors are visualized by using the high speed camera and spray angle. Penetration etc. are measured. Experimental results are summarized as follows ; 1) Correlations of spray Penetration is expressed as follows $$0 $$t_b 2) Correlations of spray Angle is expressed as follows $$T_a=293K \;;\; tan({\theta}/2)=0.59({\rho}_a/{\rho}_f)^{0.437}$$ $$T_a=473K\;;\; tan({\theta}/2)=0.588({\rho}_a/{\rho}_f)^{0.404}$$ 3) The measured macro characteristics - spray tip penetration and spray angle agreed well with established correlations.