• Journal of Korean Tunnelling and Underground Space Association
• /
• v.10 no.3
• /
• pp.269-282
• /
• 2008

In general, the effects of steel ribs are not considered in the numerical analysis of tunnel design. However, attempts have been increased recently to consider these effects in the analysis of shallow tunnels in soft ground, based on the fact that the steel ribs embedded in the shotcrete take a role to support some portion of the redistributed load due to excavation. In such analyses, the steel ribs can be considered in four different methods: (1) a conventional method where the steel ribs are not considered, (2) a method using the equivalent composite cross section in which the bending moment of shotcrete is not considered, (3) a method using the equivalent composite cross section in which both the compressive stress and the bending moment for the shotcrete and steel rib are considered, and (4) a method using beam elements for the shotcrete and the steel rib, respectively. These methods are adopted in the numerical analysis using FLAC 2D to investigate stresses of both the shotcrete and the steel rib. The overall results show that the analyses are more practical and economical when the effects of steel rib are considered fer the methods (2), (3), and (4). Since the results of those analyses considering steel rib capacity may be different according to the ground condition, it will be necessary to consider the appropriate method among them in accordance with design conditions.

• Journal of the Korea Concrete Institute
• /
• v.15 no.2
• /
• pp.335-343
• /
• 2003

In the previous experimental study, it is verified that the ultimate strain of concrete (${\varepsilon}$$_{cu}$=0.003) and coefficient of equivalent stress block (${\beta}$$_1$) can be used for the analysis of RC beams under biaxial and uniaxial bending moment. However, the characteristics of stress distribution of non rectangular compressed area in the RC columns are different to those of rectangular compressed area. The properties of compressive stress distribution of concrete have minor effect on the pure bending moment such as beams, but for the columns subjected to combined axial load and biaxial bending moment, the properties of compressive stress distribution are influencing factors. Nevertheless, in ACI 318-99 code, the design tables for columns subjected to axial loads with bidirectional eccentricities are based on the parameters recommended for rectangular stress block(RSB) of rectangular compressed areas. In this study the characteristics of stress distribution through both angle and depth of neutral axis are observed and formulated rationally. And the modified parameters of rectangular stress block(MRSB) for non rectangular compressed area is proposed. And the computer program using MRSB for the biaxial bending analysis of RC columns is developed and the results of MRSB are compared to RSB and experimental results respectively.

• Journal of Korean Society of Steel Construction
• /
• v.13 no.5
• /
• pp.493-502
• /
• 2001

This paper describes a seismic design procedure for rib-reinforced RBS(Reduced Beam Section) steel moment connections. Engineers often use rib plates to enhance seismic performance of steel moment connections. thinking that the 2nd moment of inertia is increased so that the tensile stress in the beam flange groove weld is reduced However the force transfer mechanism in the rib connections is completely different from that as predicted by the classical beam theory ; a clear diagonal strut action is present in the rib. By treating the rib as a strut the writer has recently proposed an equivalent strut model that could be used as the basis of a practical design procedure. In this paper the proposed equivalent strut model is briefly presented first. A step-by-step design procedure is then recommended based on the proposed model.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.04a
• /
• pp.354-359
• /
• 1995

회전익의 소재로 복합재료를 선택하게 됨에 따라 헬리콥터의 유지, 보수 및 성능에서 유리하게 되었지만 허브 형태의 간소화로 인하여 해석상의 어려움은 확대 되었다고 할 수 있을 것이다. 따라서 회전익의 단면특성은 더욱 중요한 의미를 갖게 되었다. 회전익의 단면특성을 결정하기 위해서 우선적으로 각 방향운동의 연성항을 소거하는 것이 계산상 유리하고 따라서 관성주축방향을 결정하는 것이 중요하다. 그러나 회전익의 익형이 대칭형이 아니고 복합한 재료로 구성되어 있을 뿐 아니라 효율의 극대화를 위하여 축방향을 따라 비틀림을 부여하고 있기 때문에 관성주축의 방향을 결정하는데 많은 어려움이 존재한다. 따라서 본 연구에서는 실제 회전익을 그 연구 대상으로 회전익 단면의 등가강성행렬을 추출하고 외팔보의 공학이론과 회전행렬을 이용하는 방법으로 관성주축방향을 결정하는 방법을 제시하였다. 해석방법의 타당성을 확보하기 위하여 엄밀해를 알고 있는 간단해 단면을 갖는 외팔보를 이용하여 검증하였다. 이러한 방법은 관성주축방향을 결정하는 새로운 프로그램의 개발이라는 부담을 최소화 하였을 뿐 아니라, 해석방법 자체가 가지는 간편성으로 인하여 많은 시간과 노력을 줄일수 있을 것으로 기대된다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.1 s.92
• /
• pp.78-83
• /
• 2005

LTCC filters have been widely used to wireless terminals. They generally adopt the multilayer structure. Some of multilayer LTCC filters are made of symmetrical parallel-coupled lines and anti-symmetrical parallel-coupled lines to reduce the length of resonators. The equivalent circuit of parallel-coupled lines was analyzed and applied to bandpass filters using multilayer parallel-coupled line resonators. The three-pole bandpass filter with the center frequency of 2.45 GHz is designed by using the proposed equivalent circuit and the measured results have good agreement with the design results.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.21 no.4
• /
• pp.401-410
• /
• 2008

The natural frequency of a beam plays an important role in not only vibration analysis but also understanding its dynamic characteristics. It is complicated to analyse the natural frequency of a stepped beam with discontinuously varying section. Approximate analysis methods such as Rayleigh-Ritz method, FEM, etc. are frequently used for the vibration analysis of stepped beams. In such a case, accuracy of these methods depends upon the number of partitioned elements, the number of the iterations in calculation and the assumed mode shape. This study presents an approximate analysis method for the fundamental natural frequency analysis of stepped cantilever beam, using equivalent beam transformation technique. Validity and usefulness are verified by comparing the proposed method with FEM for several example problems.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.19 no.1 s.71
• /
• pp.55-62
• /
• 2006

The natural frequency of a beam plays a critical role in the dynamic analysis of beams. Especially it is a complicated and difficult task to analyse the natural frequency of a stepped beam with an irregularly varying section. The lumped mass methods, multi-degree of freedom analyses, are mainly used for the analysis of this kind of stepped beams. The accuracy of these methods are determined by the number of the partitions of elements, the number of the iterations in calculation, and the accuracy of assumed mode shapes. This study presents a method of transformation from symmetrically stepped beams to an equivalent beam and a method of the eigenvalue analysis. Appropriateness and utility of this method are demonstrated by comparing examples from other literatures and various models.

• Journal of the Korea Concrete Institute
• /
• v.23 no.6
• /
• pp.781-790
• /
• 2011

This paper contains the experimental results on strengthening effect of RC beams strengthened with NSM CFRP reinforcement and various strengthening details. A total of 14 beams have been tested to analyze strengthening effects of NSMR with various reinforcement details. Variables were cross-sectional shape of CFRP reinforcements, strengthening areas, grooves the number and location etc. Test results revealed that failure modes of NSMR showed two types. One was bond failure at interface between concrete and filler and the other was CFRP rupture. Also, failure mode of specimens with two grooves occurred premature bond failure because of superposition of failure surfaces at concrete around grooves. failure mode of MI specimens considered the equivalent section have changed bond failure to CFRP rupture and CFRP efficiency has improved 83% to 100%.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2001.05a
• /
• pp.492-492
• /
• 2001

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.3A
• /
• pp.227-234
• /
• 2011

Recently, a high strength concrete of more than 40 MPa has been increasingly used in practice. However, use of the high strength concrete may influence on design parameters, particularly stress distribution. This is very true since the current everyday practice employs equivalent rectangular stress distribution that is derived from normal strength concrete. Subsequently, the stress distribution seems to be reevaluated and then a new distribution with new parameters needs to be suggested for the high strength concrete. For this purpose, linear and multiple regression analyses have been carried out in term of using experimental data for the high strength concrete of 40 to 80 MPa available in literatures. Accordingly, new parameters associated with the stress distribution have been proposed and employed for the design of flexural and compressive members. Comparative design examples indicate that designs with new parameters reduce section dimensions compared to those with the current code parameters for concrete strengths of 40 to 70 MPa. In particular, for compressive members, design with new parameters exhibit conservative compressive force compared to those with the current code parameters.