• The Journal of the Korea institute of electronic communication sciences
• /
• v.18 no.5
• /
• pp.835-840
• /
• 2023

Compared to 3D FEM, 2D FEM can be analyzed by simplifying the model and conditions. However, with respect to coil conditions, in many cases, direction of coils(upward, downward, entrance, exit, etc.) are sequentially configured and set up the FEM analysis conditions. This paper shows simplification of coil conditions and reduction of analysis time by applying the equivalent winding method composed of one FEM coil even if it has multiple slots, and shows consistency of results by applying it to a winding type magnetic gear.

• Journal of Korean Society of Steel Construction
• /
• v.9 no.3 s.32
• /
• pp.363-375
• /
• 1997

This study encompasses the performance of static and fatigue test for the 8 large scale test specimens to clarify the fatigue behavior of coped stringer and the effect of the repair and strengthening on the damaged stringer of the floor system in steel railway bridges. For the purpose of the research, the actual stress wave for the existing bridge was measured, the basic stress range frequency histogram was made and the equivalent stress range was calculated. Using the result from the equivalent stress range made by adjusting the stress range, the static and fatigue test was carried out by identifying the previous rehabilitation and after. As the result of the static tests, it was revealed that the level of local stress under the S1 specimen test of the real equivalent stress range was similar to tensile strength of the test material, and it was consistent with the requirement of the initiation condition of the fatigue crack. Through the various rehabilitation methods to the damaged specimens, the effects of the repair and reinforcement were analyzed. According to the results of the repair of effect, bolting the high tension bolt over the stop hole was confirmed to be more adequate method than drilling only stop hole to delay the fatigue crack growth. Futhermore, in case of the stringer subjected by bending moment, the reinforcement over the upper flange side was determined to be a useful strengthening method, and the reinforcement to the web of the stringer was not appropriate to accomodate as a adequate strengthening method. Also it was confirmed that the category of the fatigue design for the coped stringer met with the category E specified on the fatigue design criteria of the Highway Standard Specification in Korea.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.7B
• /
• pp.1268-1278
• /
• 1999

In this paper, we propose an analytic method for dimensioning of traffic descriptors at the leaky bucket-based UPC for VBR MPEG video traffic on ATM networks. We analytically derive cell violation probabilities at the UPC by using the proposed scene-based video traffic model, and then we show that it is possible to select sets of traffic descriptors that have the same required violation probability. For two example video traces, numerical results show that our proposed traffic descriptors dimensioning method can approximate well the simulation-based traffic control results of the real video traces. When the effective bandwidth allocation method of an ON/OFF model is used for the call admission control in the networks, we present an efficient traffic descriptor selection method by studying the allocated bandwidth to each possible traffic descriptor set.

• The KSFM Journal of Fluid Machinery
• /
• v.11 no.4
• /
• pp.32-37
• /
• 2008

In this study, we have introduced an improved equivalent modeling technique for large scale composite wind-turbine blade. Conventional or general equivalent modeling procedure may give critical error in the analysis results because of geometric coupling effects. For the analyses of structural vibration and aeroelastic problems, the accuracy of equivalent structural models is very important since it can have high numerical efficiency and various practical applications. Three-dimensional realistic composite wind-turbine blade model is practically considered for numerical study. In order to validate the effect of the mass and the stiffness of the equivalent beam model, comparison study based on the natural vibration analysis has been conducted, and the accuracy levels of the conventional and modified equivalent modeling techniques are presented.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.1
• /
• pp.71-76
• /
• 2008

Nonlinear dynamic system under random excitation was analyzed by using stochastic method. A linearization method was used in order to linearize non-linear structural characteristics but the parametric excitation was used as it was given. An equivalent energy method which equalizes the expectation value of energy of the original nonlinear system and that of quasi-linearized system was proposed. Ito's differential rule was applied to obtain steady state moments. Quasi-linearization coefficients can be obtained the iterative calculation of linearization scheme and steady state moments. Monte Carlo simulation was used to verify the results of the proposed method. Nonlinear vibration of a slender beam was analyzed in this research. The analysis results were compared with Monte Carlo simulation result and showed good agreement. As the spectral density of the given excitation increased, the analysis results showed the better agreement with Monte Carlo simulation.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.1068-1073
• /
• 2007

3D finite element analyses of a corrugated steel web girder and a steel truss web girder are conducted to investigate the static and dynamic behaviour of the hybrid girders. And the analyses results are compared with those by the equivalent beam theory. The equivalent theory is a theory that all section properties of a truss structure are replaced by section properties of a beam including the shear coefficient. When applying the equivalent beam theory, the shear coefficient of the corrugated steel web girder is estimated as the area ratio of total section to web section and that of the steel truss web girder is calculated by the equation proposed by Dewolf. Static deflections and natural frequencies by 3D finite element analyses and the those by the equivalent beam theory are relatively in good agreement.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.12 no.4
• /
• pp.537-549
• /
• 1999

선형탄성 파괴해석은 균열을 갖는 변형률 경화재료의 파괴거동을 예측하는데 불충분하기 때문에 최근에는 균열 선단 부에서 대규모 소성 역을 갖는 균열 체에 적용할 수 있는 많은 파괴역학개념이 제안되고 있다. 따라서, 본 연구에서는 대규모항복 조건하의 연성파괴를 보이는 평판을 정확하게 해석할 수 있는 새로운 유한요소모델을 제시하고자 한다. 균열 선단 부의 응력 장을 정의하는데 가장 지배적인 파괴매개변수인 J-적분 값과 소성 역의 크기 및 형상을 J-적분법과 등가영역적분법을 통해 파괴거동을 설명할 수 있도록 증분소성이론에 기초를 둔 p-version 유한요소해석이 채택되었다. 제안된 유한요소모델에 의한 수치해석결과는 이론 해와 h-version 유한요소해석과 비교되었다.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.310-313
• /
• 2010

본 논문에서는 등가소성힌지길이 개념을 새롭게 개선하여 도입함하여 구조물의 거동특성을 평가하는 프로그램을 개발하였다. 시간의 경과 및 외부환경 변화와 더불어 발생 가능한 지하구조물의 변상은 해당 구조물의 구성재료 및 작용하는 외압의 형태 등에 의해 다르게 나타나게 된다. 즉, 장기적인 지반외력의 변화에 의해 콘크리트 구조체의 천단부에 큰 휨압축응력과 인장을력이 생기는데, 내측에는 압축이 생기고 외측에는 인장균열이 발생한다. 또한 측벽이나 어깨부에서는 인장응력과 전단응력에 의한 균열이 발생하기도 한다. 따라서 개발된 프로그램으로 균열발생단면에 대하여 축력, 휨모멘트, 균열폭을 서로 연관 지을 수 있게 될 뿐만 아니라 균열폭의 확장을 추적해 나갈 수 있다. 해석기법을 토대로 개발된 해석모듈을 이용하여, 본 해석 기법의 타당성에 대한 검증을 실시하였다. 검증을 위해서는 수평보구조와 터널구조에 대해 각각 해석을 수행하였다. 그 결과, 구조물 내에서의 균열의 진전이 점차적으로 확장되어 가는 것이 표현 가능한 것을 확인하였으며, 해석결과의 타당성을 확인하였다.

• Journal of the Society of Naval Architects of Korea
• /
• v.31 no.1
• /
• pp.102-110
• /
• 1994

The roll response of ships to the narrow band random exciting moment is investigated based on the multiple time scale technique. The results are compared with those calculated from statistical equivalent linearization method. The calculation results have shown that the results calculated from multiple time scale technique eve wider range of multiple values. Numerical simulations of rolling motion of ship are performed to confirm the results.

• Journal of IKEEE
• /
• v.8 no.1 s.14
• /
• pp.136-144
• /
• 2004

From the AC analysis results utilizing a two dimensional device simulator, the ac equivalent-circuit modeling of the ESD protection devices is executed. It is explained that the ac equivalent circuit of the NMOS protection transistor is modeled by a rather complicated form and that, depending on the frequency range, the error can be large if it is modeled by a simple RC serial circuit. It is also shown that the ac equivalent circuit of the thyristor-type pnpn protection device can be modeled by a simple RC serial circuit. Based on the circuit simulations utilizing the extracted equivalent circuits, the effects of the parasitics in the protection device on the characteristics of LNA are examined when the LNA, which is one of the important RF circuits, is equipped with the protection device. It is explained that a large error can result in estimating the circuit characteristics if the NMOS protection transistor is modeled by a simple capacitor. It is also confirmed that the degradation of the LNA characteristics by incorporating the ESD protection device can be reduced a lot by adopting the suggested pnpn device.