• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.3
• /
• pp.1-8
• /
• 2000

This paper presents a simulation model of the Quadrature detector to demodulate FSK signal, which is widely used in wireless paging system for its simple hardware implementation and economics of It fabrication. Quadrature detecter has nonlinear phase characteristic for changes linear changes of input signal frequency. So until now Quadrature detector system analysis remained a difficult problem and performance analysis has not been carried out adequately On these backgrounds, this paper presents the FSK signal demodulation process using Quadrature detector and optimal performance derived from digital simulation technique. First, PSN(Phase Shift Network) which is composed of analog RLC tank circuit is transformed into its equivalent digital transfer function using First-order-hold theorem. Though the demodulated outputs of the Quadrature detector for 4FSK are 4-level signals, only 2 comparators are used and it is shown that optimal performance can be obtained by choosing operation parameter Q value and threshold level decision which are proposed herein.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.5 s.120
• /
• pp.530-538
• /
• 2007

An inductor library for efficient low cost RFIC design has been developed based on a standard digital 0.18 ${\mu}m$ CMOS process. The developed library provides four structural variations that are most popular in RFIC design; standard spiral structure, patterned ground shield(PGS) structure to enhance quality factor, stacked structure to enable high inductance values in a given silicon area, multilayer structure to lower series resistance. Electromagnetic simulation, equivalent circuit, and parameter extraction processes have been verified based on measurement results. The extensive measurement and simulation results of the inductor library can be a great asset for low cost RFIC design and development.

• Transactions of the KSME C: Technology and Education
• /
• v.5 no.2
• /
• pp.115-126
• /
• 2017

This paper proposes an accelerated life evaluation of drive shaft for the power train parts of special purpose vehicle. It is necessary the real load data of usage level driving load condition for life evaluation of power train parts, but we can't get the load spectrum data for evaluation in many case of special purpose vehicle. So, in this paper, the road load spectrum data for evaluation is created by modeling and simulation based on vehicle data and special road condition. The inverse power model is used for accelerated life test. The equivalent torque of load spectrum is achieved using the Miner's Rule. This paper also proposes the calibrated acceleration life test method for drive shaft. The fatigue test is performed through three stress levels. The lifetime at normal stress level is predicted by extrapolation, and is verified through comparison of experimental results and load spectrum data.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.1
• /
• pp.51-58
• /
• 2001

Recently, DC-DC converters significantly increase the total losses as rising switching frequency. Trnditional soft switching technique for reducing switching losses even increase voltage/Clment stress of switch In this paper, Resonant circuit for soft switching is connected in parallel with power stage and only operates just before tum-on of the main sWItch. Therefore, ills doesn't affect the total circuit QI'||'&'||'pound;ration. The object of tIns paper is to make the linearized equivalent loss mxleIs. and to analyze the total losses by experiment. ZVT-PWlvI converter designed with 170-260[V] input, 400[V] 5[A] output, and 100[kHz] switching frequency is tested respectively with 500[W], 1[kW], 1.5[kW], and 2[kW] loads. The total losses in input 220[V], 2[kW] load are analyzed by usirm the linearized equivalent loss models.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.10
• /
• pp.5974-5979
• /
• 2014

Lightweight parts with very uniform precision are manufactured by an indent method and the press technique has been improved. Upon assembly with an indent method, a deformation force due to the compressive force occurs between the pin and hole and the contact surface is affected by damage. Therefore, a 3 dimensional model was made using the CATIA program and the damage on the surface contacted with indent was estimated through the ANSYS program in this study. In the analysis result, the maximum load applied at the PCB plate was 21.3 N when the pin goes through the PCB plate. When PCB plate came out of the pin, the maximum load was 19.24 N. As the structural analysis result, the maximum equivalent stress of Pin 1 was 192.96MPa because the maximum stress occurs at Pin 1 among all parts of this study model. By examining the damage property of the contacted indent and applying this study result to the design of real indentation, the damage can be prevented and the durability can be estimated.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.9B
• /
• pp.1527-1533
• /
• 2000

Basically, a general characterization procedure based on the extraction of the characteristic impedance and propagation constant for analyzing a single MIS(Metal-Insulator-Semiconductor) transmission line is used. In this paper, an analysis for a new substrate shielding MIS structure consisting of grounded cross-bars at the interface between Si and SiO2 layer using the Finite-Difference Time-Domain (FDTD) method is presented. In order to reduce the substrate effects on the transmission line characteristics, a shielding structure consisting of grounded cross bar lines over time-domain signal has been examined. The extracted distributed frequency-dependent transmission line parameters and corresponding equivalent circuit parameters as well as quality factor have been examined as functions of cross-bar spacing and frequency. It is shown that the quality factor of the transmission line can be improved without significant change in the characteristic impedance and effectve dielectric constant.

• Tunnel and Underground Space
• /
• v.15 no.2 s.55
• /
• pp.145-156
• /
• 2005

MODFLOW, 3-D finite difference code, is widely used to model groundwater flow and has been used to assess the effect of excavations on the groundwater system due to construction of subways and mountain tunnels. The results of numerical analysis depend on boundary conditions, initial conditions, conceptual models and hydrogeological properties. Therefore, its accuracy can only be enhanced using more realistic and field oriented input parameters. In this study, SA(simulated annealing) was used to integrate hydraulic conductivities from a few of injection tests with geophysical reference images. The realizations of hydraulic conductivity random field are obtained and then groundwater flows in each geostatistically equivalent media are analyzed with a numerical simulation. This approach can give probabilistic results of groundwater flow modeling considering the uncertainty of hydrogeological medium. In other words, this approach makes it possible to quantify the propagation of uncertainty of hydraulic conductivities into groundwater flow.

• The KIPS Transactions:PartB
• /
• v.11B no.3
• /
• pp.345-352
• /
• 2004

This paper deals a method to deliver more realistic sound by cancelling the cross-talk which is inherent to the 5.1 channel speaker system. The acoustical model for cross-talk cancellation is the free field model. This model minimizes distortion of sound. 1 used the bark scale sound quality compensation which based on psycho-acoustic. For the surround channels, band-limited sound quality compensation is performed in the frequency domain. I also performed the sound qualify assessment test on the traditional 2 channel stereo and 5.1 channel system. This test is performed in the tort chamber which satisfies the ITU-R specifications. 1 uses the IACC(Inter-Aural Cross-Correlation) to determine the preferences of the amateur and the golden ear experts to asses the trans-aural filter. According to the result from the proposed method, I got more the 38dB separation rates with the Dolby standard speaker array. The results on the diffusion by the subjective test with the experts shows 0.4∼0.5 point Increased then before.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.22 no.6
• /
• pp.700-705
• /
• 2012

This paper addresses an intelligent digital redesign (IDR) technique for observer-based output-feedback control systems, in order to efficiently convert a pre-designed Takagi-Sugeno fuzzy model-based analog controller into a sampled-data one in the sense of state matching. A delta operator is used to get an asymptotic relation between the analog and the sampled-data control systems. The IDR problem is viewed as a minimization problem of the norm distances between linear operator to be matched. The condition is represented as linear matrix inequalities, and the separation principle on the IDR is shown.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.5
• /
• pp.857-862
• /
• 2008

This paper evaluate the performance using a simulated 490KHz narrow band filter based on characteristic parameters appropriately extracted from 490KHz band-pass filter after considering each characteristic, which is modeled on equivalent circuit and applied to NAVTEX receiver using crystal oscillator. The evaluation results show that the value of a series capacitor of crystal oscillator has only little capacity by Cs=21.094fF and the bandwidth characteristics of filter go worse as the capacity value of crystal oscillator grow increase. Moreover, the series inductance value of crystal oscillator has a relatively big value by L=5H, therefore the bandwidth characteristic according as inductance's capacity shows more little effect than the capacity.