• Title/Summary/Keyword: 드릴

Search Result 510, Processing Time 0.029 seconds

A Study on Micro Drill-Bit Measurement Using Images (영상을 이용한 미세 드릴비트 측정에 관한 연구)

  • Kwak, Dong-gyu;Choi, Han-go
    • Journal of the Institute of Convergence Signal Processing
    • /
    • v.16 no.3
    • /
    • pp.90-95
    • /
    • 2015
  • This study presents a method to test quite small-sized and light-weighted micro-drill bits which are used to make holes in printed circuit boards(PCB). After getting images of micro-drill bits through the high resolution microscope, we developed image processing algorithms to detect fiducial points, and then measured diverse factors of the drill-bit based on these points. We also developed the window-based inspection system to automatically discriminate normal and abnormal status. For the relative comparison of its performance, the system was compared with an existing inspection system using test images. Experimental results showed that the proposed system slightly improved performance, and also classified correctly some misjudged errors which were occurred in the existing system.

Influences of Air Cavity on the Sensitivity of a Mandrel Type fiber Optic Acoustic Sensor (Air cavity가 맨드릴형 광-음향센서의 감도특성에 미치는 영향)

  • 임종인;노용래
    • The Journal of the Acoustical Society of Korea
    • /
    • v.19 no.2
    • /
    • pp.3-7
    • /
    • 2000
  • This paper is on the sensitivity characteristics of a concentric composite mandrel type fiber optic acoustic sensor with inclusion of an air cavity With the finite element method, we have analyzed sensitivity variation of the sensor in relation to its geometrical factors such as thickness of the air cavity, thickness of the foaming layer, and the ratio of inner diameter/outer diameter of the mandrel. Results of the analysis suggest a thicker air cavity, a thinner foaming layer, and a smaller ratio of the inner diameter/outer diameter of the mandrel to be desirable for higher sensitivity. The sensor structure designed with the above rules provides the sensitivity of about 0.8dB higher than that of a normal concentric composite mandrel sensor without the inherent air cavity.

  • PDF

Characteristics of Delamination Factor and Surface Roughness by Drilling Condition for Glass Fiber Reinforced Plastic Composites (유리섬유복합재의 드릴가공조건에 대한 박리지수와 표면조도 특성)

  • Lee, Ok-Kyu;Ahn, Dae-Keon;Choi, Jin-Ho;Kweon, Jin-Hwe
    • Composites Research
    • /
    • v.26 no.6
    • /
    • pp.380-385
    • /
    • 2013
  • Characteristics of delamination factor and surface roughness by drilling condition for glass fiber reinforced plastic (GFRP) composites were investigated in this paper. An expression to quantify the delamination factor was induced by using image pixels of the entry and the experimental drilling was accomplished by fabricating several GFRP specimens in condition of minimizing the effect of vibration and heat. A method for measuring 6 points average surface roughness was applied to acquire the more reliable roughness values. The experimental results showed that the delamination factor was decreased as the feed rate was increased and it was also slightly decreased as the cutting speed was increased. Also, it was investigated that the surface roughness at inner surface of drilled holes was increased as the feed rate was increased, whereas the roughness values were not affected by the cutting speed variation.

Evaluation of Pull-out Performance of Torsion Control Expansion Anchor According to Drill Bit Diameter (드릴비트 직경에 따른 비틀림 제어 확장 앵커의 인발성능 평가)

  • Kyoung-Hun Chae;Tae-Wo Park;Moo-Won Hur;Yeong-Seung An;Ju-Yeon Han
    • Journal of the Korea institute for structural maintenance and inspection
    • /
    • v.27 no.1
    • /
    • pp.64-70
    • /
    • 2023
  • In this study, reliability tests of torsion control expansion anchors according to drill bit diameters were performed. The standard deviation and coefficient of variation of the anchor were reviewed through the tests for each variable, and the results were compared and evaluated with the standard test results. As a result of the reliability test of the M12 and M16 anchors with 1.04 times the drill bit diameter, they were within 20% of the ultimate tensile load permissible standard coefficient of variation. It was found that the pulling-out performance of the anchor installed in the large hole was sufficiently secured. However, it was found to be about 253% and 210% of the design strength, indicating that the pulling performance of the anchor installed in 1.04 times the drill bit diameter was sufficiently secured. As a result of the reliability test of the M12 and M16 anchors with 1.02 times the drill bit diameter, the value of the coefficient of variation of the ultimate tensile load limit was within 20%, which satisfies the test standard. It was shown to be about 136% and 168% of the design strength, indicating that the pulling-out performance of the anchor installed in 1.02 times the drill bit diameter is sufficiently secured.

The Effects of Seeding Pattern and Rate on the Yield and Agronomic Characters of Barley Under Different Cultural Conditions (대맥의 파종양식 및 파종밀도가 몇가지 재배조건하에서의 수량 및 주요실용형질에 미치는 영향)

  • Pyeong-Ki Yim
    • KOREAN JOURNAL OF CROP SCIENCE
    • /
    • v.21 no.1
    • /
    • pp.136-179
    • /
    • 1976
  • Effects of seeding pattern and rate on the yield and some agronomic characters of barley under different cultural conditions were observed at Suweon, Daejeon and Jinju during the barley growing season from 1972 to 1974. Plant height and culm length were increased by dense seeding, shading, heavy fertilization, moving location down to the lower latitude. The tiller number per plant, dry matter weight, leaf number on main stem, percentage of valid tillers, RGR, NAR, and $R_{A}$ were increased by heavy fertilization, sparse seeding, reduced furrow width and drilling likewise the length, width and angle of leaf. The newer cultivar had higher RGR and NAR. The higher yielding cultivars had higher potential for carbohydrate assimilating ability. Straw weight and grain yield were increased by dense seeding, reduced furrow width, drilling, heavier fertilization and moving the location to the south, and then decreased by shading and late seeding. High yield increase by drilling was found in late seeding. The optimum seeding rate for the yield increase were 15l/10a for furrow and 25l/10a for drilling. The spike number type cultivars were favourable for the sparse seeding and the spike weight type cultivars seemed to be suitable to the dense seeding, The repeatability of days to heading due to location and fertilizer level was higher than that of seeding time and seeding method. Repeatability of culm length was extremly high in seeding method and comparatively high in fertilizer level while low in location. The repeatability of yield due to location and seeding methods was comparatively high, but the tendency was different along with different cultivars. Also the repeatability of yield due to the fertilizer level was generally high except cultivar Haganemngi.

  • PDF

A Study on the PCB(Printed Circuit Board) Drilling by Air Bearing Spindle (공기 베어링 스핀들을 애용한 PCB 드릴링에 관한 연구)

  • Bae Myung-Il;Kim Sang-Jin;Kim Ki-Soo
    • Journal of the Korean Society for Precision Engineering
    • /
    • v.22 no.3 s.168
    • /
    • pp.15-20
    • /
    • 2005
  • This paper describes the PCB drilling using an ultra high-speed air bearing spindle system and micro drill. For this research, we have developed the ultra high-speed air bearing spindle of 125,000 rpm and made an experiment for the application possibility in the PCB drilling. In order to estimate the drilling performance, we have investigated the size and damage of drilled hole, and the wear of drill at 90,000rpm. Results are as follows; we have confirmed the possibility in the PCB drilling of air bearing spindle. In case of micro-drilling PCB at $0.1mm\sim0.3mm$, the increase in the number of drilling has resulted in a bigger size of holes and also a bigger size of damage. It has been found that the wear of micro drill tends to concentrate in the main cutting edge.

Cutting Torque Control in Drilling Part 2 : Drilling Torque Control Using Spindle Motor Current and Its Effect on Drill Flank Wear (드릴 공정시 절삭 토크 제어 제 2 편 : 주축 모터 전류를 이용한 드릴링 토크의 제어와 드릴 플랭크 마모에 대한 영향)

  • O, Yeong-Tak;Kim, Gi-Dae;Ju, Jong-Nam
    • Journal of the Korean Society for Precision Engineering
    • /
    • v.18 no.8
    • /
    • pp.107-115
    • /
    • 2001
  • Drilling torque was measured indirectly using the spindle motor current and controlled in real time through feedrate manipulation in a machining center. The PID controller designed in the previous paper was applied to drilling torque control. A series of cutting experiments were performed for various cutting conditions. Experimental results showed that the drilling torque was well regulated at a given reference level by feedrate manipulation in all cutting conditions. The increase in the cutting torque and temperature according to the increase in machining depth was suppressed and the risk of the drill failure and the drill flank wear were reduced remarkably through cutting torque control. Moreover, the suggested cutting torque control system doesn\`t disturb the cutting process and is practical for industrial environment. Therefore, the proposed culling torque control system will contribute to productivity improvement in drilling process.

  • PDF

Diagnosis of the Drill Wear Based on Fuzzy Logic (퍼지 논리를 이용한 드릴의 마모 상태 진단)

  • 권오진;최성주;조현찬
    • Journal of the Korean Institute of Intelligent Systems
    • /
    • v.11 no.9
    • /
    • pp.833-836
    • /
    • 2001
  • One of the most important technology in Factory Automation and Unmanned Automation is to construct the diagnostic system for manufacturing process. To improve the productivity in cutting process, the state of tools such as bite, drill, endmill should be monitored continuously. In this study, fuzzy logic was used to check the wear of drill in drilling process. The input variables to construct the fuzzy rules are cutting force and the rate of cutting force's change. The experiment was done with the fixed spindle speed and feed rate in cutting condition. The proposed algorithm is verified by comparing Fuzzy wear with real wear measured.

  • PDF

The effect of guided flapless implant procedure on heat generation from implant drilling (수술가이드를 이용한 무피판 임플란트 술식에서 임플란트 드릴링이 열발생에 미치는 효과)

  • Yoo, Je-Hyeon;Jeong, Seung-Mi;Choi, Byung-Ho;Joo, Sang-Don
    • The Journal of Korean Academy of Prosthodontics
    • /
    • v.51 no.1
    • /
    • pp.11-19
    • /
    • 2013
  • Purpose: The aim of this study was to evaluate the heat generation in bone in vitro during the guided flapless drilling procedure and the effect of drilling methods on the heat generation. Materials and methods: A model that has missing the first and second mandibular molars bilaterally was used. In group A, classical flap implant surgery was performed. In group B, flapless implant surgery using surgical guide was performed. In group C, flapless implant surgery using surgical guide without up-and-down pumping motion was performed. Temperature was measured with k-type thermocouple and a real-time digital thermometer. The thermocouples were placed at 0.5 mm away from the osteotomy area at the depths of 3 mm and 6 mm. The measured values were evaluated with independent t-test. Results: The mean temperature generated was $27.2^{\circ}C$ ($SD{\pm}2.1^{\circ}C$) and $27.5^{\circ}C$ ($SD{\pm}2.3^{\circ}C$) for groups A and B, respectively. These differences were not statistically significant. In group C, the mean temperature was $37.0^{\circ}C$ ($SD{\pm}3.4^{\circ}C$). There were statistically significant differences between groups B and C with respect to the mean temperature. Conclusion: These findings suggest that guided flapless drilling with up-and-down pumping motion may not significantly increase the bone temperature.