• 한국정밀공학회지
• /
• 제23권9호
• /
• pp.47-53
• /
• 2006

An Experiment was carried out to find the scheme far minimization of burr formation on inclined exit surface in drilling. Several drills with different geometry are used for drilling the workpiece with inclined exit surface. Step drills are specified with step angle and step size. The influence of the inclination angle of exit surface on burr formation was observed, which enables to analyze the burr formation mechanism on inclined exit surface. Along the edge on the inclined exit surface, burrs are formed by the bending deflection to feed direction and also burrs are formed in exit direction of cutting edge. To minimize the burr formed in feed direction, the corner angle which is formed by the inclination angle and step angle must be large enough not to be bent to burr. By decreasing step angle of drill and decreasing the distance between two axes of two holes, burr formation at the intersecting holes can be minimized. Burr formation mechanisms are analyzed according to the drill geometries and cutting conditions. Several schemes far burr minimization on inclined exit surface were proposed.

• 한국정밀공학회지
• /
• 제23권4호
• /
• pp.29-36
• /
• 2006

Micro drilling by high-speed air bearing spindle is very useful manufacturing technology in electronic industry For the design of high speed air bearing spindle, there are considered stability of air bearing spindle, allowable load of air bearing, run out and tooling system design for micro drill's attach and remove. According to suggested details, we designed and manufactured high-speed air bearing spindle and carried out performance estimation such as run out, temperature change in running air bearing spindle, stiffness, chucking torque. Results are follows; Run out was measured under $5{\mu}m$ at air bearing spindle revolution $20,000\sim125,000rpm$. High speed air bearing spindle's temperature rose about $20^{\circ}C$ after 5 minutes from running and then was fixed. Allowable thrust load of spindle was 17kgf. Chucking torque of collet was 15kgfcm.

• Composites Research
• /
• 제16권2호
• /
• pp.1-8
• /
• 2003

본 논문에 한국항공우주연구원에서 개발 중인 KSR-III 로켓의 탑재부 축소형 킥모터 구조 설계와 제작공정 개발 내용을 정리하였다. 경량화를 위해 복합재료를 적용하였으며, 복합재 연소관 제작에 널리 사용되는 필라멘트 와인딩 방법을 도입하였다. 복합재 구조설계에는 망목이론(netting theory)과 적층판 이론을 사용하여 요구되는 내압하중에 적합한 와인딩 두께를 결정하였고, 돔형상은 와인딩 및 맨드렐(mandrel) 제작의 편이성을 고려하여 결정하였다. 재료는 경량화를 목표로 T-800 탄소 섬유와 고온용 수지로 선정하였다. 또한 와인딩 후 맨드렐를 제거하기 위해 조립식 맨드렐을 개발하여 적용하였다.

• 대한기계학회논문집A
• /
• 제29권8호
• /
• pp.1146-1152
• /
• 2005

Recently, multi cell tube which is used for a cooling system of automobiles is mainly manufactured by the conform extrusion but this method is inferior as compared with direct extrusion in productivity per the unit time and in the equipment investment. Therefore, it is essential for the conversion of direct extrusion with porthole die. The direct extrusion with porthole die can produce multi cell tube which has the competitive power in costs and qualities compared with the existing conform extrusion. This study is designed to evaluate metal flow, welding pressure, extrusion load, tendency of mandrel deflection that is affected by variation of porthole shape in porthole die. Estimation is carried out using finite element method under the non-steady state. Also this study was examined into the cause of mandrel fracture through investigating elastic deformation of mandrel during the extrusion.

• 한국기계가공학회지
• /
• 제16권4호
• /
• pp.83-88
• /
• 2017

Recently, the use of advanced materials with light weight significantly increases because of global regulation on CO2 emission. Especially, CFRP (carbon fiber reinforced plastics) one of the most promising advanced materials. Since CFRP has pretty higher strength per unit weight than steel, it is one of most popular materials in aviation industry and its application to automobile rises sharply. Especially, one of the frequent machining processes for CFRP is drilling to make a hole, however, CFRP drilling has troublesome limitations in hole quality and productivity induced due to delamination, splintering and severe tool wear. Particularly, cutting loads increase caused by tool wear makes delamination and splintering even severer. Therefore, tool wear monitoring or reduction in CFRP drilling must be considered seriously. In this study, we measured thrust force, flank wear, and tool surface temperature in drilling using various tools with different sizes and materials. Consequently, it was presented the effects of tool properties on drilled hole quality, thrust force and tool surface temperature.

• 한국기계가공학회지
• /
• 제17권4호
• /
• pp.1-8
• /
• 2018

In drilling Inconel 601, which is used for compressor cases in aircraft engines, a lot of cutting oil must be supplied. This prevents tools from wear and fracture due to the heat buildup resulting from the high-temperature resistance and toughness of this alloy. However, the cutting oil supply has compromised the machining environment. This has caused attention to shift to an environmentally friendly cutting fluid supply system called the Minimum Quantity Lubrication(MQL) system. The aim of this study was to find a more efficient drill processing method using MQL and to verify its performance. To that end, the properties of Inconel that make it difficult -to -drill were studied by a comparison with the drilling of SM45C. Specific factors (i.e., cutting force and tool wear) were examined in relation to the conditions in the MQL-based drilling system. Based on these results, a sealed cover and step feed were proposed as measures to increase the effectiveness of the MQL system. The efficiency of the proposed method was established.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제50권11호
• /
• pp.575-582
• /
• 2001

This paper presents a calculating method of switching angle for adaptive switched reluctance motor (SRM) drive of a drill. The operation of the SRM is completely characterized by the flux linked by one phase winding which depends only on the current in that same phase winding and the rotor position. An efficiently adaptive SRM drive is possible on appropriately scheduling the commutation angles with accurate rotor position, supplied current value and speed information. An adaptive SRM drive with reduction torque ripple should be controlled by an optimized phase current control along with rotor position. Therefore, we are suggested a computing method of switching turn-on and off angles for adaptationally SRM operation with varied rotor speed and load. To probe the computing method, we have some simulation and experiment, it is shown a good result that can be computing the optimized switching angles for an electric drill motor.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.479-484
• /
• 1996

This paper describes a method of measuring tilt motion. This method measures the tilt motion of drilling machines using a laser interferometer, a simple sliding linear bearing, measurement of the probe and the LSC(least square center) method. The next order of business is discussing the procedure of measurement. First, The measured position is considered to be the point of contact between the drill shank and the probe. The revolution of the drill axis delivers the point of contact to the probe. Second, because the laser interferometer is attached on the sliding linear bearing, any movement of probe influences laser reflector. Thus, the laser program displays the moving factor of laser reflector. Namely, this is tilt factor. Third. the points of measurement are a full circle which has 8 points (each are 45$^{\circ}$), After it is finished measuring the 8 points, let the spindle of the drilling machine move down about 5 cm. Repeating this procedure three times, we can get tilt motion's values which are calculated by LSC method. Many error factors affect the accurate measurement of tilt motion. However in this paper we ignore some error factors because they are less significant than tilt motion.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 춘계학술대회논문집; 경주코오롱호텔; 22-23 May 1997
• /
• pp.146-152
• /
• 1997

This paper deals with a study of striker type impact hammer drill for improving the drilling performance. The study was performed through a numerical simulation of the impact hammer mechanism, an experimental comparison of the numerical simulation results and an optimization of the impact mechanism. The numerical model of the impact hammer drill takes into account the striker motion and the effects of the pressure in the cylinder as well as the friction acting on the striker. The equation of motion is solved with the pressure equation in the cylinder and the friction force. At the moment of impact, an ideal impact model that uses restitutiion codfficient is used to calculate the sudden change of the striker motion. The impact force numerically simulated shows a good agreement with the experimental results and thus, the validity of the numerical model is proven. Based upon the proposed model, an optimization was performed to improve the impact force of the hammer drill. The objective function is to maximize the impact force and the design variables are striker mass, frequency of piston, bit guide mass, cylindrical diameter and dimensions of the mechanism components. Each design variable and some other conditions that are essential to maintain normal operation of the hammer drill are considered as constraints. The optimized result shows remarkable improvement in impact force and an experimental proof was investigated.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.303-303
• /
• 2011

최근 세포 포집 소자 제작에 있어 세포의 종류와 크기의 다양성을 고려하여 정확하게 포집하기 위한 고정밀화, 소형화 된 도구 제작 기술 개발이 중요한 현안으로 떠오르고 있다. 본 연구에서는 선행 기술에서의 세포 포집 한계를 극복하기 위한 방안으로 펨토초 레이저 가공을 통한 미세 세포 포집 장치 제작에 관한 실험을 진행하였다. 펨토초 레이저의 짧은 파장의 대역 범위와 전력 특성이 미세 소자 제작을 가능하게 함에 따라 수백, 수천 개의 세포 포집에 있어 보다 안정적이고 신뢰도 높은 포집 장치 구현을 실현시킬 수 있다. 실험에서는 펨토초 레이저의 가공 조건을 가변하며 MEMS 소자에 홀(hole)을 형성시켰다. flatness 200인 Polycarbonate 재질의 기판 위에 CNC공작기계를 사용하여 유로를 제작하고 상부에 젤라틴 코팅 부분 2를 포함한 총 두께 12의 membrane 필름을 부착하였다. 이후 775 nm 파장의 펨토초 레이저를 사용하여 10${\times}$10 개수의 홀을 형성 한 후 홀 주위의 thermal damage와 레이저의 파워에 따른 홀의 형태와 크기 변화를 비교하였다. 실험 결과 membrane 막의 젤라틴 코팅 측면 홀의 평균 직경은 레이저의 파워와 비례하여 증가하였으며, 레이저 파워가 일정한 임계치에 도달하면 특정 시점에서 수렴됨을 확인하였다. 또한 PET 측면의 직경은 서서히 증가하고 빠르게 일정한 값으로 수렴됨을 확인하였다. 본 실험에서는 펨토초 레이저의 특성 파라미터와 레이저의 가공 조건을 수립함으로써 실험에서 사용 된 레이저를 이용한 드릴링 방안을 제시한다.