• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.3
• /
• pp.10-17
• /
• 2003

In this paper, genetic algorithm (GA)-based Thin Film Bulk Acoustic Resonator (FBAR) RF filter design technique is proposed. Since the BVD(Butterworth-Van Dyke) lumped element model is valid only around the resonance, FBAR filter design technique based on BVD circuit has an approximate error. Instead of using BVD model, optimizing filter design method utilizes an analytical electrical impedance equation of FBAR. The geometry of FBAR such as thickness of the piezoelectric layer and area which significantly affect the filter response is optimized by GA. US-PCS Rx Bandpass filter obtained by the proposed technique shows a better response comparing with the typical and BVD-based filter.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.34 no.6
• /
• pp.347-353
• /
• 2021

In this study, we presented a novel size optimization framework to control the linear buckling temperature and several buckling modes of plates, by optimizing thickness values of composite structures for practical engineering applications. Predicting the buckling temperature and mode shape of structures is a vital research topic in engineering to achieve structural stability. However, optimizing designs of engineering structures through engineering intuition is challenging. To address this limitation, we proposed a method that combines finite element simulation and size optimization. Based on the idea that the structural buckling temperature and mode shape of a plate are affected by the thickness of the structure, the thickness values of the nodes of the target structure were set as the design variables in this optimization method; and the buckling temperature values, and buckling mode shapes were set as the objective functions. This size optimization method enabled the determination of optimal thickness distributions, to induce the desired buckling temperature values and mode shapes. The validity of the proposed method was verified in terms of their buckling temperature values and buckling mode shapes, using several numerical examples of rectangular composite structures.

• Composites Research
• /
• v.24 no.2
• /
• pp.38-45
• /
• 2011

In this paper, we present an optimization method for the single Dallenbach-layer type microwave absorbers composed of E-glass fabric/epoxy composite laminates. The composite prepreg containing carbon nanotubes (CNT) was used to control the electrical property of the composites laminates. The design technology using the genetic algorithm was used to get the optimal thicknesses of the laminates and the filler contents at various center frequencies, for which the numerical model of the complex permittivity of the composite laminate was incorporated. In the optimal design results, the content of CNT increased in proportion to the center frequency, but, on the contrary, the thickness of the microwave absorbers decreased. The permittivity and reflection loss are measured using vector network analyzer and 7 mm coaxial airline. The influence of the mismatches in between measurement and prediction of the thickness and the complex permittivity caused the shift of the center frequency, blunting of the peak at the center frequency and the reduction of the absorbing bandwidth.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.1
• /
• pp.15-20
• /
• 2017

The main purpose of the ball valve ball is to be moved by the rotation of the stem when fully open or completely closed. In this study the heat of the initial model, which used a structure interaction analysis technique, tried to examine the structural safety of the high temperature for the ball valve. In the initial model the stress of the exiting sheet was more than the yield strength. We selected two design shapes with variables of length and thickness for the optimization of the sheet. The Kriging interpolation method was applied to a meta-model-based optimization technique. As a result, it was possible to find a thickness and length for the sheet within the yield strength. This was done by measuring the value of the capacity coefficient of the valve and evaluating the performance of the ball valve.

• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.4
• /
• pp.71-77
• /
• 2011

Main parameters of the screen printing were determined and the printing parameters were optimized for 0402, 0603, and 1005 chips in this study. The solder pastes used in this study were Sn-3.0Ag-0.5Cu and Sn-0.7Cu. The process parameters were stencil thickness, squeegee angle, printing speed, stencil separating speed and gap between stencil and PCB. The printing pressure was fixed at 2 $kgf/cm^2$. From ANOVA results, the stencil thickness and the squeegee angle were determined to be main parameters for the printing efficiency. The printing efficiency was optimized with varying two main parameters, the stencil thickness and the squeegee angle. The printing efficiency increased as the squeegee angle was lowered under 45o for all chips. For the 0402 and the 0603 chips, the printing efficiency increased as the stencil thickness decreased. On the other hand, for the 1005 chip, the printing efficiency increased as the stencil thickness increased.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.253-253
• /
• 2010

유리 기판 상에 시스템 온 패널과 같은 차세대 디스플레이 구현과 평판형 디스플레이의 문제점 해결을 위하여 비휘발성 메모리 소자 등의 전자 소자 집적화와 빠른 구동 속도를 가진 박막트랜지스터가 요구된다. 본 논문에서는 비휘발성 메모리 소자에서 MONOnS 각 layer층의 두께 따른 특성에 대한 연구를 진행하였다. 실험은 ONO 구조를 12.5nm/35nm/2.7nm, 12.5nm/20nm/2.3nm, 8.5nm/10nm/2.3nm, 6.5nm/10nm/1.9nm 의 두께로 증착하였다. ${\Delta}VFB$, Retention time, capacitance을 측정하여 oxide/Nitride/Oxynitride 층의 두께 변화를 통해 최적화된 tunneling layer와 charge storage layer, 그리고 blocking layer의 두께를 알 수 있다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.50.1-50.1
• /
• 2010

결정질 실리콘 태양전지의 원가에서 Wafer는 60~70%의 매우 높은 비중을 차지하고 있다. 많은 연구들이 원가 절감을 위하여 Wafer의 두께를 감소시키는 것에 집중하고 있다. 그러나 Wafer 두께의 감소는 태양전지의 효율 감소와 공정 진행 중에 파손율이 상승하는 등의 문제가 발생한다. 이에 본 논문에서는 결정질 태양전지 구조 중에서 24.7% 이상의 최고 변환 효율을 갖는 PERL(Passivated Emitter, Rear Locally diffuse) 구조를 대상으로 wafer 두께 감소에 따른 변환 효율 감소의 원인과 해결 방안을 제시하고자 한다. Simulation으로 확인한 결과 370 um 두께의 wafer에서 24.2 %의 효율은 50 um 두께의 wafer에서는 20.8 %로 감소함을 확인할 수 있었다. 얇아진 wafer에서 감소한 효율을 개선하기 위하여 후면 recombination velocity, 후면 fixed charge density, 후면 산화막 두께 등을 다양화하여, 각각의 경우에 대한 cell의 효율 변화를 살펴보았다. 그 결과 후면 recombination velocity, 후면 fixed charge density, 후면 산화막 두께를 최적화 하여, 각각 2.8 %p, 1.5 %p, 2.8 %p의 효율 개선 효과를 얻었다. 위 세 가지 효과를 동시에 적용하면 50 um wafer에서 370 um wafer 효율의 결과와 근접한 24.2 %의 효율을 얻을 수 있었다. 향후에는 위의 결과를 바탕으로 실제 실험을 통하여 확인할 계획이다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.443-443
• /
• 2008

본 연구에서는 Ga-doped ZnO(GZO)-Ag-GZO 다층 투명전극을 Dual DC magnetron sputtering system을 이용 하여 유리기판 위에 상온에서 제작하여 Ag 두께에 따른 전기적, 광학적, 구조적 특성변화를 조사하였다. Hall effect measurement와 UV/Vis spectrometer로 전기적, 광학적 특성을 분석하였으며, X-ray diffraction(XRD)와FE-SEM분석을 통해 결정성과 표면 특성을 조사하였다. FE-SEM 분석결과 island 형태에서 continuous layer로 박막의 형상이 바뀌면서 다층 투명전극의 전기적, 광학적 특성에 영향을 미치는 것을 알 수 있었다. 본 실험에서 Ag 두께 12 nm에서 가장 최적화되어 유리기판위에 상온에서 증착되었음에도 불구하고 $5.5{\times}{\times}10^{-5}\Omega$-cm, $6\Omega$/sq. 의 매우 낮은 면저항과 비저항을 각각 나타내었고 550 nm 파장에서 87 % 의 높은 광 투과도를 나타내었다. 또한 두께 12 nm의 Ag가 삽입된 다층 투명전극을 polyethylene terephthalate (PET) 기판위에 성막하여 Bending test를 실시하여 0.1% 이하의 매우 낮은 저항변화를 확인함으로써 플렉시블 기반의 디스플레이나 태양전지의 투명 전극으로서의 응용 가능성을 확인하였고 마지막으로 최적화된 다층 투명전극을 유기물태양전지의 애노드에 적용하여 기존 ITO 애노드를 대체할 수 있는 투명전극으로서의 가능성을 제시하였다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.2
• /
• pp.131-135
• /
• 2013

In this study, to develop a light weight duo type aluminum LPG tank in stead of a conventional steel tank optimization technology is used. Two types of optimization method are carried out for internal compression test simulation of a LPG tank. The first is the thickness only optimization of LPG tank components. The second is the thickness and shape optimization. For the case of the thickness only optimization the weight reduction rate of an optimized tank compare to that of the initial design is 42%. Also 48% weight reduction was achieved for the case of the thickness and shape optimization.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.05a
• /
• pp.29-29
• /
• 2015

Al과 Ni이 나노 두께로 적층되어 있는 나노 포일은 외부의 촉발에 의해 원자수준의 상호 확산을 통해 합금화 된다. AlNi 합금이 되서 $-{\Delta}H$의 변화로 인하여, 외부에 열을 공급하게 되어 최대 엔탈피의 변화 일어날 수 있는 Al과 Ni의 혼합비율을 조사하였다. 나노 포일의 제조 공정은 마그네트론 스퍼터링을 이용하였으며, 나노 박막의 두께 및 적층 공정에 대한 공정 최적화를 하였다. 제조된 나노 포일은 금속-세라믹의 상온접합을 실시하여 산업적 응용에 대한 가능성을 고찰하고자 하였다.